I didn't managed to make it work, too much errors with the commands inside the install.sh.
I will wait a future compatible version of Recalbox, for now I will try to use it for another project. Thank you for your help !
Alors j'ai trouvé une solution, mais je ne comprends pas trop pourquoi ça fonctionne :p
J'ai dans un premier temps mis : global.videomode=default
Mais surtout (car ça ne fonctionnait tjrs pas) j'ai réglé le Shader Sets en mode Retro... et ça fonctionnait !
Alors j'ai dû également mettre un peu plus bas dans recalbox.conf, dans Emulators choices : snes.videomode=default, sinon les jeux snes ne fonctionnait pas non plus.
@ian57 Hey, thank you for answering, this is my configuration:
It's the same as the one in that link but I used Notepad ++ to edit the config.txt instead of that SSH thing which I don't understand much, is that the problem?
By default the Recalbox image works perfectly on my 24" Monitor, i don't know what could be the problem...
@mediccby please give details about your hardware and the release of recalbox you are running.
If you have very little skills in linux, you should try the unstable recalbox 4.1 release. The 3.2 tft waveshare is supported out of the box thanks to a simple configuration in the recalbox.conf file and config.txt file (fbcp at startup is managed)
## fbcp FrameBuffer Copy Program
## For small TFT screen on GPIO and SPI
## See https://github.com/recalbox/recalbox-os/wiki/Utility---Use-of-fbcp-for-small-TFT-screen-%28EN%29 for details
## Needed for Waveshare 3.2" 3.5" TFT screen, 2.8" Adafruit screen
## See https://github.com/recalbox/recalbox-os/wiki/TFT-Screen-SPI-Bus-%28EN%29
## for support and configuration details needed by /boot/config.txt
Ahh I see comments right sounds good thanks man :) have been searching all over the place and no good results now that I fee confident in this and especially changing the config text on RecalBox I'm going to purchase it to finish off my Arcade prototype.
Sorry for reviving this topic, but I think the information about this is few, and some more wouldn´t hurt. So, first of all, I am using Putty, notepad++ and FileZilla. I am following the steps shown on: https://github.com/recalbox/recalbox-os/wiki/TFT-Screen-SPI-Bus-(EN) in order to get a 2.8" tft display from waveshare to work. Why am I following the steps to the 3.2" tft if mine is a diferent version? Well, waveshare says "2.8inch RPi LCD (A) and 3.2inch RPi LCD (B) are compatible with each other (the only differences are screen size and keys count), and can be mutually substituted in most cases." (the website: https://www.waveshare.com/product/2.8inch-rpi-lcd-a.htm) So, I want to verify it by managing my 2.8" display to work with recalbox as well, but I am running into some problems, back to the github guide, (sorry for the newbie language and questions) what does " after getting the binary" means? Should I wait for something after making the change to the file? Well, that´s not the question I want to make. What should I do if the comand (chmod 755 fbcp) shows up as "No such file or directory"? I tried and moved the file from my computer to the directory that was ahead of that comand, that was supposed to run. Then, after that, I tried the command again and guess what, it gave me answer! I was like, ok, it was the wrong order, but then, I tried to run fbcp by writing on Putty: fbcp. No such file... Bla bla. So, the screen as well didn´t change from white. I don´t know what to do. I am a student and wanted to use it as a " console" for a project. I guess I will try again tomorrow but I would apreciatte as much help as possible, so that, after I am sucessful I can post on every forum this in order to people as me don´t have so much work and I can test if the 2.8" works as the 3.2". Thanks again, I will post this on other forums too.