@shad0wware69 Found a better script that was made for the official fan in mind. https://github.com/tedsluis/raspberry-pi-pwm-fan-control. Disregard the above post.

@lumpy

It looks like there's a setting in fba2x.cfg called maintain_aspect_ratio.

I don't have a Gpi case and I can't test it, have you read the documentation for this emulator?
https://wiki.recalbox.com/en/emulators/consoles/neo-geo/fba2x

@caboose hello
hardware, recalbox version ?
https://forum.recalbox.com/topic/3647/before-posting

I may have misunderstood some of the translation. I mixed the files and this worked for me.

This boot.ini

ODROIDXU-UBOOT-CONFIG # U-Boot Parameters (DO NOT MODIFY) setenv version 4.14 setenv zimage boot/linux setenv fdtbin boot/exynos5422-odroidxu4.dtb setenv uInitrd boot/uInitrd # --- Screen Configuration for HDMI --- # # --------------------------------------- # Uncomment only ONE line! Leave all commented for automatic selection. # Uncomment only the setenv line! # --------------------------------------- # ODROID-VU forced resolution # setenv videoconfig "video=HDMI-A-1:1280x800@60" # ----------------------------------------------- # ODROID-VU forced EDID # setenv videoconfig "drm_kms_helper.edid_firmware=edid/1280x800.bin" # ----------------------------------------------- # 1920x1080 (1080P) with monitor provided EDID information. (1080p-edid) setenv videoconfig "video=HDMI-A-1:1920x1080@60" # ----------------------------------------------- # 1920x1080 (1080P) without monitor data using generic information (1080p-noedid) # setenv videoconfig "drm_kms_helper.edid_firmware=edid/1920x1080.bin" # ----------------------------------------------- # 1920x1080 50hz (1080P) with monitor provided EDID information. (1080p 50hz-edid) # setenv videoconfig "video=HDMI-A-1:1920x1080@50" # ----------------------------------------------- # 1920x1080 50hz (1080P) without monitor data using generic information (1080p 50hz-noedid) # setenv videoconfig "drm_kms_helper.edid_firmware=edid/1920x1080_50hz.bin" # ----------------------------------------------- # 1440x900 with monitor provided EDID information. # setenv videoconfig "video=HDMI-A-1:1440x900@60" # ----------------------------------------------- # 1440x900 without monitor data using generic information # setenv videoconfig "drm_kms_helper.edid_firmware=edid/1440x900.bin" # ----------------------------------------------- # 1280x1024 without monitor data using generic information # setenv videoconfig "drm_kms_helper.edid_firmware=edid/1280x1024.bin" # ----------------------------------------------- # 1280x720 (720P) with monitor provided EDID information. (720p-edid) # setenv videoconfig "video=HDMI-A-1:1280x720@60" # ----------------------------------------------- # 1280x720 (720P) without monitor data using generic information (720p-noedid) # setenv videoconfig "drm_kms_helper.edid_firmware=edid/1280x720.bin" # ----------------------------------------------- # 1024x768 without monitor data using generic information # setenv videoconfig "drm_kms_helper.edid_firmware=edid/1024x768.bin" # ----------------------------------------------- # 1024x600 without monitor data using generic information (ODROID VU7+) # setenv videoconfig "drm_kms_helper.edid_firmware=edid/1024x600.bin" # ----------------------------------------------- # 800x600 without monitor data using generic information # setenv videoconfig "drm_kms_helper.edid_firmware=edid/800x600.bin" # ----------------------------------------------- # 800x480 without monitor data using generic information (ODROID 7") # setenv videoconfig "drm_kms_helper.edid_firmware=edid/800x480.bin" # ----------------------------------------------- # 720x576 without monitor data using generic information # setenv videoconfig "drm_kms_helper.edid_firmware=edid/720x576.bin" # ----------------------------------------------- # 720x480 without monitor data using generic information # setenv videoconfig "drm_kms_helper.edid_firmware=edid/720x480.bin" # ----------------------------------------------- # 640x480 without monitor data using generic information # setenv videoconfig "drm_kms_helper.edid_firmware=edid/640x480.bin" # --- HDMI / DVI Mode Selection --- # ------------------------------------------ # - HDMI Mode setenv vout "hdmi" # - DVI Mode (disables sound over HDMI as per DVI compat) # setenv vout "dvi" # --- CPU Governor Setup --- # Uncomment only one line. New governor is set after 90secs after boot. # ------------------------------------------ # - Performance (Keep all the CPU's at Maximum frequency) setenv governor "performance" # ------------------------------------------ # - Ondemand # setenv governor "ondemand" # ------------------------------------------ # - Interactive (Pretty much just like ondemand with more possible customization via sysfs.) # setenv governor "interactive" # ------------------------------------------ # - Conservative (Like ondemand, but do the frequency transitions more slowly, great for battery powered applications) # setenv governor "conservative" # ------------------------------------------ # - Powersave (Keeps the CPU's to the lowest possible temps) # setenv governor "powersave" # --- HDMI CEC Configuration --- # ------------------------------------------ setenv cecenable "false" # false or true # set to true to enable HDMI CEC #------------------------------------------------------------------------------ # # HDMI Hot Plug detection # #------------------------------------------------------------------------------ # # Forces the HDMI subsystem to ignore the check if the cable is connected or # not. # false : disable the detection and force it as connected. # true : let cable, board and monitor decide the connection status. # # default: true # #------------------------------------------------------------------------------ setenv HPD "false" setenv hdmi_phy_control "HPD=${HPD} vout=${vout}" if test "${cecenable}" = "false"; then fdt rm /soc/cec@101B0000; fi setenv dtb_addr_r "0x44000000" setenv dtbo_addr_r "0x48000000" setenv zimage_addr_r 0x40008000 setenv uInitrd_addr_r 0x42000000 setenv fdtbin_addr_r 0x44000000 setenv config_addr_r "0x4B000000" setenv fdt_high "0xffffffff" # load config.ini load mmc 0:1 ${config_addr_r} config.ini \ && ini generic ${config_addr_r} # DRAM Frequency (lpddr3 available frequency list - 933/825/728/633) setenv ddr_freq 933 # set DDR frequency dmc ${ddr_freq} # Default boot arguments setenv bootrootfs "label=RECALBOX" setenv console "console=ttySAC2,115200n8 consoleblank=0 vt.global_cursor_default=0" # boot commands fatload mmc 0:1 ${zimage_addr_r} ${zimage} fatload mmc 0:1 ${uInitrd_addr_r} ${uInitrd} fatload mmc 0:1 ${fdtbin_addr_r} ${fdtbin} fdt addr ${dtb_addr_r} if test "${cecenable}" = "false"; then fdt rm /cec@101B0000; fi setenv bootargs "${bootrootfs} ${console} governor=${governor} ${videoconfig} ${hdmi_phy_control}" # load overlays from config.ini if test "x${overlay_profile}" != "x"; then ini overlay_${overlay_profile} ${config_addr_r} fi if test "x{overlays}" != "x"; then fdt resize ${overlay_resize} for overlay in ${overlays}; do load mmc 0:1 ${dtbo_addr_r} overlays/${overlay}.dtbo \ && fdt apply ${dtbo_addr_r} done fi bootz ${zimage_addr_r} ${uInitrd_addr_r} ${fdtbin_addr_r}

This config.ini

[generic] ; Device Tree Overlay overlay_resize=16384 ; uncomment next line to enable Odroid XU4 OGST overlay_profile=hktft_cs_ogst overlays="spi0 i2c0 i2c1 uart0" [overlay_hktft_cs_ogst] overlays="hktft-cs-ogst i2c0"

And these settings in recalbox.conf

# ------------ J - TFT SECONDARY SCREEN ----------- # #Second miniTFT screen as marquee to display scrapes and videos #Enable it with system.secondMiniTFT.enabled=1, disable with system.secondMiniTFT.enabled=0 #this configuration is REQUIRED system.secondminitft.enabled=1 #Type of mini TFT : OGST, unknown #Most of spi tft screen are enabled thanks to overlays in /boot/config.txt in rpi and /boot/config.ini on odroidxu4 #please check the specific configuration of your screen #Some examples are available on the page ..... # values are : # - overlay : screen configured through overlays in /boot/config.txt or /boot/config.ini (odroidxu4/ogst) # - default : the rest of the world #this configuration is REQUIRED if system.secondminitft.enabled=1 system.secondminitft.type=overlay #Choose the resolution of your screen #miniTFT resolution 320x240 -> 240p, 480x320 -> 320p #this configuration is REQUIRED if system.secondminitft.enabled=1 system.secondminitft.resolution=240p #Scraped image aspect on tft screen : fbv display option # options available : stretch, ignore-aspect, enlarge. # stretch : Strech (using a simple resizing routine) the image to fit onto screen if necessary # alpha : use the alpha channel (if applicable) # ignore-aspect : Ignore the image aspect while resizing # enlarge : Enlarge the image to fit the whole screen if necessary # 1 = enabled, 0 = disabled #this configuration is REQUIRED if system.secondminitft.enabled=1 system.secondminitft.imagestretchenabled=1 system.secondminitft.imageenlargeenabled=0 system.secondminitft.imagealphaenabled=1 system.secondminitft.imageignoreaspectenabled=1 #When activating the second TFT screen, you may want to display #game scraped video only on the second screen. This variable #allows you to disable scraped video playing in ES during game browsing #system.secondminitft.disablevideoines=1 disable video playing in ES #system.secondminitft.disablevideoines=0 enable video playing in ES #this configuration is OPTIONAL if system.secondminitft.enabled=1 ;system.secondminitft.disablevideoines=1 #if the backlight of your your screen can be manage by PWM, #indicates the GPIO value of your PWM control #WiringPi and its gpio program will be used to control the backlight #when RB goes in SLEEP mode, and when it wakes up. #On raspberry pi, PWMs cannot be used simultaneously with Jack sound output. #If your are using HDMI or a Audio hat you can use backlight PWM control for the second screen #If you are using Jack output please leave commented. #The Screen will be switch down in Sleep mode, and switch on when it wakes up. #On OGST, only this mode is available. #this configuration is OPTIONAL if system.secondminitft.enabled=1 ;system.secondminitft.backlightcontrol=18 # system.secondminitft.usemarquee variabla allows you to display a different # image during running game. just creat a directory named "marquees" in media # aside videos and images and put new images with the same name as in images # example : # - /recalbox/share/roms/neogeo/media/marquees/alpham2.png # - /recalbox/share/roms/neogeo/media/images/alpham2.png # if set to 1, in game the marquee images will be displayed # if set to 0, in game the scraped images will be displayed ;system.secondminitft.usemarquee=0 #system.secondminitft.sleepenabled allows you to enable/disable #sleep mode for the second TFT. If set to 1 sleep mode is enabled and #backlight of the screen will be OFF. If set to 0, sleep mode is #disabled and the backlight of the screen will be always On ;system.secondminitft.sleepenabled=0

Thank you for the help

@deruesch

Why is it not possible to update KODI by itself?

Because that's not the Recalbox philosophy. Recalbox is as plug an play as possible, and everything is tested before releasing to users.

When could we get an update in Recalbox?

We have a small team of developers who do as much as possible to fix bugs and make improvements, it is not possible to give release predictions until most of the tested changes are in place, when possible the release date is announced publicly, not in individual threads .

You can follow the changelog here:
https://gitlab.com/recalbox/recalbox/blob/master/CHANGELOG.md

@borg357 Sorry, I've never used FTP on Recalbox, I use WinSCP or I transfer over the network via file explorer.
The documentation specifies that you can use Cyberduck for SFTP connections:

https://recalbox.gitbook.io/documentation/v/francais/tutoriels/systeme/acces/acces-sftp-ssh-via-cyberduck-macos-win

See if these threads help you, they mention the use of FTP (if you use the forum search system, you will find even more mentions of FTP that can help you):

https://forum.recalbox.com/topic/24266/jeux-ports-avec-la-7-2-1/15 https://forum.recalbox.com/topic/23811/xbox-series-s-x-controller-not-pairing-with-recalbox-7-1/3

@zing Thanks! I will trie it.

@digitalumberjack thanks for the help, i got the download now!! greetings

@edwinsources It would be of great help if someone could share the 3 files already modified for me just to replace the files config.txt, user_confing.txt and recalbox.conf

I got it to work! I re-installed Recalbox 7.2.2 again and re-added all the content and it works now. No idea why. Thanks for trying to help me figure this whole thing out, I really appreciate it!

@zing Many thanks again for more info. I guess ill have a dive into whats possible with the event scripts in EmulationStation.

Thanks for helping me understand more about the system, hopefully I can work something out after some reading.

Fingers crossed.

@hez83 said in login fail:

hey
try to login per terminal .root and recalboxroot.
than only a #.
nthing happens..
just a #.
recalbox works..
but i need to acces via terminal to install an 3.5 tft

thanks

Hi @hez83

Actually, the # means you are logged in.

David