Unsolved Script to turn off cooler

[lackyluuk]

@azvarel you could do something like I did some time ago..and then if you shut down your recalbox, just set the GPIO of the transistor to LOW.

But..a big BUT..I think the gpio has an undefined logic level if the software is shut down. Just try it out. I also need to check how mine is behaving its a long time ago

https://forum.recalbox.com/topic/3704/push-button-on-off-script-problems/10

[Substring]

@azvarel Setting a GPIO to a logical 1 level means outputting 3.3V i think. Beware of the current level, a GPIO can't deliver much

[azvarel]

@lackyluuk said in Push button (ON/OFF) script problems?:

@PenPen: I am sorry for this way too late answer. Not sure if you need an answer anymore

Here is an example with GPIO pin 14 for controlling the fan. The indents might not be correct I had a little trouble with copy/paste the code
Hope I can help you with this

#!/usr/bin/env python

import os
import time
import RPi.GPIO as GPIO

GPIO.setwarnings(False)
GPIO.setmode(GPIO.BCM)
#Set max. temperature of CPU
TEMP_MAX = 67
ON_TIME = 200
#Set pin 14 as transistor gate
GATE = 14
#Set pin 14 as an output and shut down
GPIO.setup(GATE, GPIO.OUT)
GPIO.output(GATE, False)

def getCPUtemperature():
res = os.popen('vcgencmd measure_temp').readline()
return(res.replace("temp=","").replace("'C\n",""))

while True:

  	temp_float = float(getCPUtemperature())

  try:
  	if (temp_float > TEMP_MAX):
  		# ein
  		GPIO.output(GATE, True)
  		time.sleep(ON_TIME)
  		# aus
  		GPIO.output(GATE, False)
  	else:
  		GPIO.output(GATE, False)

except KeyboardInterrupt:
print float(getCPUtemperature())
print "power off fan..."
GPIO.output(GATE, False)
print "cancelling..."

Forgot to attach a short drawing. I used the official RaspberryPI 5V DC fan.

@lackyluuk
I will ask the questions here instead of being there.

So I understood your script when it reaches a temperature it turns on the cooler, when it cools it turns off. it is?

@Substring I'm not a programmer, I'm afraid to do something and go wrong.

[ian57]

A more simple solution is to plug the fan cooler on the USB Connector. These one are stopped when the system stops.

[lackyluuk]

@azvarel yes exactly, this script controls the fan depending on the temperature. If you don't need this you can just turn the fan ON at startup and OFF at shutdown.

Or as @ian57 alrrady mentioned, to use a USB slot if you have one free. They deliver also 5V DC.

[azvarel]

@ian57 This idea is great, but I use the other ports for usb controllers, xbox360 receiver and are on the front of SNES

If I soldered the wires at the voltage points of the USB, would it have problem when plugging a controller or a usb key? If it does not give you trouble, I do it even easier for me.

If I do not have to follow the script of @lackyluuk, I just did not understand there in the diagram the why of having a transistor, for safety?

[ian57]

@azvarel; the transitor is for switch and safety. I don't think that standard GPIO can supply enough power to run your fan correctly. So we use the +5V directly from the power supply to power the fan, and the GPIO + transitor are making the script controllable switch.

Soldering to get only the power supply is a bit risky for the plugged element I think. A fan, is a motor, and it can have bad effects on it's power circuit. And the usb deliver at max 500mA. If you try to do that .. not on an usb key slot... try it on the usb snes controller slots... it uses less current ...

If someone elsehas an idea about that?

[azvarel]

@ian57 so we went back to the script.

[Substring]

@azvarel the script looks like it takes 100% CPU, but it looks logically correct.
The electronic schematic is very simple and could help someone like @ian57 who wants to drive a 12V power supply

[lackyluuk]

@azvarel @Substring just add a time.sleep(1) or (2) into the while() loop

[tikiandskull]

Well, maybe i say a stupidity but with a thermal switch? It avoids the question of the script and you can choose one with a temperature of closing and opening of your choice.

[azvarel]

@tikiandskull nothing is stupid, any idea is valid, where would you find this thermal switch?

[tikiandskull]

@azvarel maybe something like this link text It can be found on amazon, conrad, etc some works in 5v others in 12v.

Afterwards, I do not know how it could be positioned, but probably with the probe as close as possible to cpu

(sorry for my poor English )

[Pdagarcia]

#!/usr/bin/env python3

import os
from time import sleep
import signal
import sys
import RPi.GPIO as GPIO

pin = 27 # The pin ID, edit here to change it
maxTMP = 50 # The maximum temperature in Celsius after which we trigger the fan
sleepTime = 30 # The time to sleep between temp checks

def setup():
GPIO.setmode(GPIO.BCM)
GPIO.setup(pin, GPIO.OUT)
GPIO.setwarnings(False)
return()

def getCPUtemperature():
res = os.popen('vcgencmd measure_temp').readline()
temp =(res.replace("temp=","").replace("'C\n",""))
print("temp is {0}".format(temp)) #Uncomment here for testing
return temp

def fanON():
print("Fan on ...")
setPin(True)
return()

def fanOFF():
print("Fan off ...")
setPin(False)
return()

def getTEMP():
CPU_temp = float(getCPUtemperature())
if CPU_temp > maxTMP:
fanON()
sleep(sleepTime) # Sleep additional time in order to ensure that we stay below max temp ...
else:
fanOFF()
return()

def setPin(mode): # A little redundant function but useful if you want to add logging
GPIO.output(pin, mode)
return()

try:
setup()
while True:
getTEMP()
sleep(sleepTime) # Read the temperature every x amount of seconds ...
except KeyboardInterrupt: # trap a CTRL+C keyboard interrupt
GPIO.cleanup() # resets all GPIO ports used by this script

[Pdagarcia]

With this transistor 2N4401 600 mA, 40V and 5v fan Works perfectly.

[azvarel]

@Pdagarcia where would you put this script?

[lackyluuk]

@azvarel I would place the script into /recalbox/scripts and call the script as a background process from the startup directory /etc/init.d for example as S32StartFanControl
This could look like this (just one proposal, you can do it however you like it):

#!/usr/bin/python

import subprocess

try:
    subprocess.Popen(["python","/recalbox/scripts/fanControl.py"])

except KeyboardInterrupt:
    print "Quit"

I have called my script that I start as fanControl.py

[azvarel]

@lackyluuk thanks

[marcelogarbin]

@azvarel I'm with the same problem, did you work? which method did you use?