Recalbox sur TV CRT en RGB
-
Bon ça fonctionne pas et en plus le raspberry ne se lance plus. J'ai dû toucher un truc qui fallait pas..
Je regarderai ça à tête reposée demain. -
Ian57, le Raspberry est branché en hdmi et PI2SCART (péritel), quand les 2 câbles sont branchés simultanément, le son sort de mon trinitron TV mais l'image et affiché sur mon écran de PC. Recalbox fonctionne correctement, mais l'image et sur l'un et le son sur l'autre...
Quant le Raspberry est branché uniquement en PI2SCART donc cable hdmi enlevé, le son sort de mon trinitron TV mais pas d'image sur l écran du PC.
-
@ian57 après avoir mis toutes les lignes que tu me donnes pour le fichier conf.txt voici une copie du fichier (recalbox fonctionne) mais aucune image sur le CRT.
Je précise que l'image de recalbox 6.1.1. à été installé sur une micro SD, et j'utilise une clé USB pour tout ce qui est roms et émulateur, tous les tests que je fais sont donc sans clé usb, une fois que tout fonctionnera bien avec la micro sd , je m'attaquerai a la clé pour configurer les émulateurs, voici mon fichier conf.txt :
il est de plus en plus long ...
uncomment if you get no picture on HDMI for a default "safe" mode #hdmi_safe=1 disable_overscan=1 uncomment to force a specific HDMI mode (this will force VGA) dpi_group=2 dpi_mode=8 # dpi_output_format=6 dpi_mode=87 # audio_pwm_mode=2 # hdmi_cvt=1920 240 60 1 1 0 0 # hdmi_timings=320 1 10 20 54240 1 6 8 10 0 0 0 60 0 6400000 1#240 # Sound output. Set to 0 or comment for autodetect, 1 for DVI, 2 to force HDMI. hdmi_disable_edid=0xa5000080 # display_default_lcd=1 hdmi_drive=2 hdmi_pixel_encoding=2 # Using /etc/modules is deprecated and no longer supported on 4.4 kernel So manually enable audio dtparam=audio=on force hdmi while the tv can take time before sending the signal on the hdmi output hdmi_force_hotplug=1 uncomment for composite PAL #sdtv_mode=2 uncomment for lirc-rpi enable_dpi_lcd=1 # avoid_safe_mode=1 dtoverlay=vga666 hdmi_group=1 # hdmi_mode=6 # hdmi_force=1 #if you plug your tv at the same time as your rpi and that the rpi switches from the hdmi or give a low resolution because tv had no enough time to initialize it boot_delay=3 dtparam=i2c_arm=off dtparam=spi=off uncomment if you don't want the rainbow at startup disable_splash=1 default CEC name cec_osd_name=recalbox Overclock gpu_mem_256=128 gpu_mem_512=256 gpu_mem_1024=448 avoid_safe_mode=1 kernel=zImage
-
@link71 il est tout pourri ton config.txt d'après ce que je lis, pas étonnant que ça boote pas. Il faut faire attention à la syntaxe
-
@Link71
merci de ne pas multiplier les demandes de support dans différents sujets
https://forum.recalbox.com/topic/19939/tutoriel-pi2scart-tv-crt -
@Link71 Bon ben ya surement un truc que tu ne fais pas bien!
voici mon config.txt :
# uncomment if you get no picture on HDMI for a default "safe" mode #hdmi_safe=1 disable_overscan=1 # uncomment to force a specific HDMI mode (this will force VGA) #hdmi_group=1 #hdmi_mode=1 # Sound output. Set to 0 or comment for autodetect, 1 for DVI, 2 to force HDMI. #hdmi_drive=2 # Using /etc/modules is deprecated and no longer supported on 4.4 kernel # So manually enable audio dtparam=audio=on config_hdmi_boost=0 # force hdmi while the tv can take time before sending the signal on the hdmi output hdmi_force_hotplug=1 # uncomment for composite PAL #sdtv_mode=2 # uncomment for lirc-rpi #dtoverlay=lirc-rpi # if you plug your tv at the same time as your rpi and that the rpi switches from the hdmi or give a low resolution because tv had no enough time to initialize it boot_delay=3 # uncomment if you don't want the rainbow at startup disable_splash=1 # default CEC name cec_osd_name=recalbox # Overclock gpu_mem_256=128 gpu_mem_512=256 gpu_mem_1024=448 avoid_safe_mode=1 kernel=zImage # Raise the first security limit up to 70° instead of 60° temp_soft_limit=70 #HDMI-VGA-SCART config commented #force to jack audio at boot #hdmi_ignore_edid_audio=1 #hdmi_drive=1 #increase jack sound quality #audio_pwm_mode=2 #hdmi_cvt=1920 240 60 1 1 0 0 #hdmi timings ironic #hdmi_timings=460 1 22 51 80 282 1 6 6 19 0 0 0 51 0 9600000 1 #hdmi_group=2 #hdmi_mode=87 #hdmi_cvt=1920 288 50 1 1 0 0 #hdmi_cvt=1920 288 60 1 1 0 0 #hdmi_disable_edid=0xa5000080 #Enables the ignoring of EDID/display data if your display doesn't have an accurate EDID. #hdmi_pixel_encoding=0 default (limited for CEA, full for DMT) #hdmi_pixel_encoding=1 RGB limited (16-235) #hdmi_pixel_encoding=2 RGB full ( 0-255) #hdmi_pixel_encoding=3 YCbCr limited (16-235) #hdmi_pixel_encoding=4 YCbCr full ( 0-255) #hdmi_pixel_encoding=2 #Force the pixel encoding mode. By default it will use the mode requested from edid so shouldn't need changing. #avoid_safe_mode=1 # uncomment this if your display has a black border of unused pixels visible # and your display can output without overscan #disable_overscan=1 # uncomment the following to adjust overscan. Use positive numbers if console # goes off screen, and negative if there is too much border ##overscan_left=32 ##overscan_right=32 #overscan_top=18 #overscan_bottom=4 #hdmi_drive=2 #hdmi_group=1 #hdmi_mode=6 #hdmi_force=1 #overclocking deactivated for test #arm_freq=1350 #core_freq=500 #sdram_freq=575 #force_turbo=0 #over_voltage=4 #over_voltage_sdram_p=6 #over_voltage_sdram_i=4 #over_voltage_sdram_c=4 #gpu_freq=500 #sdram_schmoo=0x02000020 #overscan_scale=1 #PiSCART config dtparam=i2c_arm=off dtparam=spi=off disable_audio_dither=1 dtparam=audio=on dtoverlay=vga666 enable_dpi_lcd=1 display_default_lcd=1 dpi_group=2 dpi_mode=87 hdmi_timings=320 1 16 30 34 240 1 2 3 22 0 0 0 60 0 6400000 1 #240
et mon recalbox.conf dans lequel j'ai juste changé
global.videomode=default
# System Variable # You can configure your recalbox from here # To set a variable, remove the first ; on the line # ------------ A - System Options ----------- # # Uncomment the system.power.switch you use ;system.power.switch=ATX_RASPI_R2_6 # http://lowpowerlab.com/atxraspi/#installation ;system.power.switch=MAUSBERRY # http://mausberry-circuits.myshopify.com/pages/setup ;system.power.switch=REMOTEPIBOARD_2003 # http://www.msldigital.com/pages/support-for-remotepi-board-2013 ;system.power.switch=REMOTEPIBOARD_2005 # http://www.msldigital.com/pages/support-for-remotepi-board-plus-2015 ;system.power.switch=WITTYPI # http://www.uugear.com/witty-pi-realtime-clock-power-management-for-raspberry-pi ;system.power.switch=PIN56ONOFF # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN) ;system.power.switch=PIN56PUSH # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN) ;system.power.switch=PIN356ONOFFRESET # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN) ;system.power.switch=PIN356PUSHRESET # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN) ## fbcp FrameBuffer Copy Program ## For small TFT screen on GPIO and SPI ## See https://github.com/recalbox/recalbox-os/wiki/Utility---Use-of-fbcp-for-small-TFT-screen-%28EN%29 for details ## Needed for Waveshare 3.2" 3.5" TFT screen, 2.8" Adafruit screen ## See https://github.com/recalbox/recalbox-os/wiki/TFT-Screen-SPI-Bus-%28EN%29 ## for support and configuration details needed by /boot/config.txt system.fbcp.enabled=0 ## Splash screen duration ## 0: Video will be played for 20 seconds (default) ## -1: All the video will be played (it won't be stopped automatically) ## >0 : Time before the video will be stopped (in seconds) system.splash.length=0 ## Recalbox Manager (http manager) system.manager.enabled=1 ## Currently, only version 2 is available system.manager.version=2 ## Recalbox security # enforce security # samba password required # disable virtual gamepads system.security.enabled=0 ## Recalbox API (REST) system.api.enabled=0 ## Allow a specific resolution for ES only from the command : tvservice -m [MODE] ## Leave commented for the default usual behaviour #system.es.videomode=CEA 4 HDMI #system.es.videomode=DMT 87 HDMI system.es.videomode=CEA 6 HDMI ## EmulationStation ### menu style ### default -> default all options menu ### none -> no menu except the game search menu ### bartop -> less menu, only needed for bartops emulationstation.menu=default ### Select a system to show on boot (use rom directory name) (string) emulationstation.selectedsystem=favorites ### Show the gamelist of the first or selected system on boot (0,1) emulationstation.bootongamelist=0 ### Disable system view. ES will boot and show ONLY the first or selected system (0,1) emulationstation.hidesystemview=0 ### Pa**e Gamelists only. Show only games listed in gamelist.xml files (0,1) emulationstation.gamelistonly=0 ### Force basicgameList view to be displayed, even if your game systems are scraped (0,1) emulationstation.forcebasicgamelistview=0 ## Videosnaps ### Delay before videosnaps start, in millisecond. Default: 2s ;emulationstation.videosnaps.delay=2000 ### Video loop times. 0 = no video. 1 or more = the video loops x times before fading out ;emulationstation.videosnaps.loop=1 ## Scrapers ### ScreenScraper.fr ### Force media region - if not defined, region is taken from system.language. Default: us ;scraper.screenscraper.region=eu ### Force text language - if not defined, region is taken from system.language. Default: en ;scraper.screenscraper.language=fr ### Choose the media to download among: ### screenshot: game screenshot ### title : game title screenshot ### box2d : Front case ### box3d : 3D rendered case ### mixv1 : Recalbox special mix image V1 (default) ### mixv2 : Recalbox special mix image V2 ;scraper.screenscraper.media=mixv1 ### ScreenScraper account ;scraper.screenscraper.user= ;scraper.screenscraper.password= ## Emulator special keys ## default -> default all special keys ## nomenu -> cannot popup the emulator menu ## none -> no special keys in emulators system.emulators.specialkeys=default ## Show or hide kodi in emulationstation (0,1) kodi.enabled=1 ## Start kodi at launch (0,1) kodi.atstartup=0 ## set x button shortcut (0,1) kodi.xbutton=1 ## Allow a specific resolution for Kodi only from the command : tvservice -m [MODE] ## By default is using the default resolution of your screen kodi.videomode=default ## Kodi can wait for a network component before starting ## waithost is the ip or hostname that must answer to a ping to validate the availability ## waittime is the maximum time waited when kodi boots ## if waitmode is required, kodi will not start if the component is not available ## if waitmode is wish, kodi will start if the component is not available ## if waitmode is not set or has another value, kodi will start immediately ;kodi.network.waitmode=required ;kodi.network.waittime=10 ;kodi.network.waithost=192.168.0.50 ## Hyperion ## Hyperion allows you to use an ambilight like led system on your recalbox ## Use hypercon to create your configuration file, and copy it in /recalbox/share/system/configs/hyperion/hyperion.config.json hyperion.enabled=0 # ------------ B - Network ------------ # ## Set system hostname system.hostname=RECALBOX ## Activate wifi (0,1) wifi.enabled=0 ## Set wifi region ## More info here: https://github.com/recalbox/recalbox-os/wiki/Wifi-country-code-(EN) wifi.region=US ## Wifi SSID (string) ;wifi.ssid=new ssid ## Wifi KEY (string) ## after rebooting the recalbox, the "new key" is replace by a hidden value "enc:xxxxx" ## you can edit the "enc:xxxxx" value to replace by a clear value, it will be updated again at the following reboot ## Escape your special chars (# ; $) with a backslash : $ => \$ ;wifi.key=new key ## Wifi - static IP ## if you want a static IP address, you must set all 3 values (ip, gateway, and netmask) ## if any value is missing or all lines are commented out, it will fall back to the ## default of DHCP ;wifi.ip=manual ip address ;wifi.gateway=new gateway ;wifi.netmask=new netmask # secondary wifi (not configurable via the user interface) ;wifi2.ssid=new ssid ;wifi2.key=new key # third wifi (not configurable via the user interface) ;wifi3.ssid=new ssid ;wifi3.key=new key ## Samba share system.samba.enabled=1 ### Virtual Gamepads system.virtual-gamepads.enabled=1 ### SSH system.ssh.enabled=1 # ------------ C - Audio ------------ # ## Set the audio device (auto, hdmi, jack) audio.device=auto ## Set system volume (0..100) audio.volume=90 ## Enable or disable system sounds in ES (0,1) audio.bgmusic=1 # -------------- D - Controllers ----------------- # # Enable support for standard bluetooth controllers controllers.bluetooth.enabled=1 # Enable ERTM controllers.bluetooth.ertm=0 ## Please enable only one of these # -------------- D1 - PS3 Controllers ------------ # ##Enable PS3 controllers support controllers.ps3.enabled=1 ## Choose a driver between bluez, official and shanwan ## bluez -> bluez 5 + kernel drivers, support official and shanwan sisaxis ## official -> sixad drivers, support official and gasia sisaxis ## shanwan -> shanwan drivers, support official and shanwan sisaxis controllers.ps3.driver=bluez # ------------ D2 - GPIO Controllers ------------ # ## GPIO Controllers ## enable controllers on GPIO with mk_arcarde_joystick_rpi (0,1) controllers.gpio.enabled=0 ## mk_gpio arguments, map=1 for one controller, map=1,2 for 2 (map=1,map=1,2) controllers.gpio.args=map=1,2 ## Custom mk_gpio arguments, ## map=5 gpio1=Y-,Y+,X-,X+,start,select,a,b,tr,y,x,tl,hk for one controller, ## map=5 gpio1=pin1,pin2,pin3,.....,pin12,pin13 ## map=5,6 gpio1=Y-,Y+,X-,X+,start,select,a,b,tr,y,x,tl,hk gpio2=Y-,Y+,X-,X+,start,select,a,b,tr,y,x,tl,hk for 2 (map=5,map=5,6) ## map=5,6 gpio1=gpiox,gpioy,gpioz,.....,gpiou,gpiov gpio2=gpiox,gpioy,gpioz,.....,gpiou,gpiov # where gpiox,gpioy,gpioz ... are NOT pin numbers on the connector, BUT location gpio numbered as in # https://www.raspberrypi-spy.co.uk/wp-content/uploads/2012/06/Raspberry-Pi-GPIO-Layout-Model-B-Plus-rotated-2700x900.png ## Set pin to -1 to disable it # controllers.gpio.args=map=5,6 gpio=4,17,27,22,10,9,25,24,23,18,15,14,2 gpio2=11,5,6,13,19,26,21,20,16,12,7,8,3 ## MCP configuration : GPIO and MCP can be used together. You can mix them. ## map=0x20,0x21 for 2 mcp23017 on i2c bus #controllers.gpio.args=map=0x20,0x21,5,6 gpio=4,17,27,22,10,9,25,24,23,18,15,14,-1 gpio2=11,5,6,13,19,26,21,20,16,12,7,8,-1 # ------------ D3 - Steam Controllers ------------ # ## Enable steam controller service controllers.steam.enabled=0 ## DB9 Controllers ## Enable DB9 drivers for atari, megadrive, amiga controllers (0,1) controllers.db9.enabled=0 ## db9 arguments controllers.db9.args=map=1 ## Gamecon controllers ## Enable gamecon controllers, for nes, snes, psx (0,1) controllers.gamecon.enabled=0 ## gamecon_args controllers.gamecon.args=map=1 ## XGaming's XArcade Tankstik and other compatible devices controllers.xarcade.enabled=1 # ------------ F - Language and keyboard ------------ # ## Set the language of the system (fr_FR,en_US,en_GB,de_DE,pt_BR,es_ES,it_IT,eu_ES,tr_TR,zh_CN) system.language=fr_FR ## set the keyboard layout (fr,en,de,us,es) system.kblayout=fr ## Set you local time ## Select your timezone from : ls /usr/share/zoneinfo/ (string) ;system.timezone=Europe/Paris # ------------ G - UPDATES ------------ # ## Automatically check for updates at start (0,1) updates.enabled=1 # Update type : default to stable updates.type=stable # ------------ H - HERE IT IS - GLOBAL EMULATOR CONFIGURATION ------------ # ## The global value will be used for all emulators, except if the value ## is redefined in the emulator ## Set game resolution for emulators ## select your mode from the command : tvservice -m [MODE] ## CEA 5 HDMI : 1920x1080 @ 60Hz 16:9, clock:74MHz interlaced ## CEA 4 HDMI : 1280x720 @ 60Hz 16:9, clock:74MHz progressive ## use 'default' for using the default resolution ## use 'auto' : switches to CEA 4 HDMI if supported, else keep the current resolution ## (string) #global.videomode=CEA 4 HDMI #global.videomode=DMT 87 HDMI global.videomode=default ## Shader set ## Automatically select shaders for all systems ## (none, retro, scanlines) global.shaderset=none ## Once enabled, your screen will be cropped, and you will have a pixel perfect image (0,1) global.integerscale=0 ## Set gpslp shader for all emulators (prefer shadersets above). Absolute path (string) global.shaders= ## Set ratio for all emulators (auto,4/3,16/9,16/10,custom) global.ratio=auto ## Set smooth for all emulators (0,1) global.smooth=1 ## Set rewind for all emulators (0,1) global.rewind=1 ## Set autosave/load savestate for all emulators (0,1) global.autosave=0 ## Enable retroarchievements (0,1) ## Set your www.retroachievements.org username/password ## Escape your special chars (# ; $) with a backslash : $ => \$ global.retroachievements=0 global.retroachievements.hardcore=0 global.retroachievements.username= global.retroachievements.password= ## Set retroarch input driver (auto, udev, sdl2) ## If you don't have issues with your controllers, let auto global.inputdriver=auto ## If you do not want recalboxOS to generate the configuration for all emulators (string) ;global.configfile=/path/to/my/configfile.cfg ## Demo screensaver parameters ## Set the system list from which ES will run random games. ## Empty list or unexisting key means all available systems global.demo.systemlist=3do,amigacd32,atari2600,atari5200,atari7800,daphne,fba_libretro,fds,gamegear,gba,lynx,mame,mastersystem,megadrive,neogeo,nes,ngpc,pcengine,sega32x,sg1000,snes ## Default demo game sessions last 90s. Change this value if you want shorter or longer sessions ;global.demo.duration=90 ## Default game info screen duration lasts 6s. Change this value if you want shorter or longer info screens. ;global.demo.infoscreenduration=6 ## Retroarch AI Translation service ## Comment out or set to 0 the following key if you don't want the AI service global.translate=1 ## Set the source and the target languages. ## Allowed language list: EN, ES, FR, IT, DE, JP, NL, CS, DA, SV, HR, KO, ZH_CN, ZH_TW, CA, BG, BN, EU, AZ, AR, SQ, ## AF, EO, ET, TL, FI, GL, KA, EL, GU, HT, IW, HI, HU, IS, ID, GA, KN, LA, LV, LT, MK, MS, ## MT, NO, FA, PL, PT, RO, RU, SR, SK, SL, SW, TA, TE, TH, TR, UK, UR, VI, CY, YI ## Setting the translate.from key to a specified language may speed up or give more accurate results ## If translate.to key is commented, the default value is extracted from system.language or, if system.language is ## undefined, set to auto (=EN). global.translate.from=auto global.translate.to=auto ## zTranslate API Key ## go to https://ztranslate.net and create an account. ## validate your account, then log in and go to the settngs page ## Look for the API Key at the bottom of the page, then uncomment the following key and paste your API Key: ;global.translate.apikey=YOUR_API_KEY_HERE ## Other translation service ## If you want to use another translation service or a custom API call, use this key to ## specify the url to call. If the key is not empty, it is used instead of zTranslation's API Key ;global.translate.url= ## Arcade metasystem ## Activate the Arcade metasystem to group all games from piFBA, FBN (libretro), MAME and optionally Neogeo ## into a single "Arcade" system. ;global.arcade=1 ## You may want to specify its position in the system list. (Default: 0) ## Negatives values may be used to tart from the end (-1 = last position) ;global.arcade.position=0 ## Include NeoGeo or not (default: 1) ;global.arcade.includeneogeo=1 ## Hide included system or leave them in the system list (default: 1) ;global.arcade.hideoriginals=1 # ------------ I - EMULATORS CHOICES ----------- # ## You can override the global configurations here ## Here is the snes example ;snes.videomode=CEA 4 HDMI snes.core=snes9x2010 ;snes.shaders=/recalbox/share/shaders/shaders_glsl/mysnesshader.gplsp ;snes.ratio=16/9 ;snes.smooth=0 ;snes.rewind=1 ;snes.autosave=0 ;snes.emulator=libretro ;snes.integerscale=0 ## If you do not want recalboxOS to generate the configuration for the emulator: ;snes.configfile=/path/to/my/configfile.cfg ## Default cores for RPi3 snes.core=snes9x2010 ## NeoGeo emulator ## You can use pifba or a libretro core (fba2x,libretro) neogeo.emulator=libretro ## If you set libretro as neogeo.emulator, the line below sets the retroarch core (fbneo, mame2000) neogeo.core=fbneo ## N64 emulator is configured to display a screen with a 640x480 resolution (native n64 resolution) ## So you must use one of these video modes (DMT 4 HDMI,CEA 1 HDMI). ## If your screen is not compatible with one of these video modes, please check the recalbox's wiki. n64.videomode=DMT 4 HDMI ## If you are using a CRT screen, please change the setting above with this one : # n64.videomode=default ## Dreamcast emulator ## Like N64, such a CPU intensive emulator needs a small resolution ## Consider DMT 4 HDMI (640*480) or DMT 9 HDMI (800*600). If you have a black screen on dreamcast, try DMT 9 HDMI here dreamcast.videomode=DMT 4 HDMI ## Demo screensaver parameters ## Include or exclude a particular system from the demo screensaver ## You may change the global.demo.systemlist key or include/exclude every single system ;snes.demo.include=0 ## Set the session duration for a particular system ;snes.demo.duration=90 # ------------ J - NETPLAY PARAMETERS ----------- # ## All these values are handled by Recalbox itself global.netplay=1 global.netplay.nickname= global.netplay.port=55435 global.netplay.relay= global.netplay.systems=fba_libretro,mame,mastersystem,megadrive,neogeo,nes,pcengine,sega32x,sg1000,snes,supergrafx global.netplay.lobby=http://lobby.libretro.com/list/ ## Configurations generated by Recalbox
Si ça marche pas vérifie ton cable péritel, certain sont des "fake" et n'utilise pas le rgb mais le composite, ouvre les prises peritel et verifie que le rgb soit cablé.
Normalement au boot du pi, ta tv doit passer automatiquement en mode AV, si ce n'est pas le cas force en mode AV avec la télécommande ou les boutons.
Si tout est ok, et que tu n'as toujours pas d'affichage alors peut être que le module piscart a un souci...
-
et tu crois que je peux abuser pour avoir un config.txt et recalbox.conf pour le hdmi vga peritel ?
d'ailleurs pourquoi il n’apparaît plus directement le recalbox.conf, y a le config et le reste mais pas ce fichier, il n'y a que recalbox-backup.
j'ai pourtant pas hiberné pendant un siècle... -
-
@ian57 alors le problème, c'est pour ça que j'ai l'impression que je suis une quiche, c'est que je sais pas s'il faut supprimer le reste ou le rajouter à un endroit précis.
Pourquoi je n'ai pas de recalbox.conf ?
Quand je lance tv service pour les dmt ou les CEA je n'ai ni le CEA 8 ni le dmt 87.
Désolé de faire mon boulet mais à l'époque je mettais pas autant pris la tête -
Le fichier recalbox.conf se situe
/recalbox/system/
'Il n a jamais ete dans la partition de boot.Il faut regarder si les valeurs existent
Si c est le cas remplace par celle indiqué dans le wiki.
Si elles sont manquantes ajoutes les.
Il ne faut surtout pas supprimer des lignes. -
-
@retrobricoleur l'utilisation de rb avec un cathodique necessite quelques connaissances de base en système linux et sur l'architecture de recalbox, ce n'est pas une utilisation standard de la distro. Du coup il est très difficile de proposer ce genre de support "out of the box" sachant que chaque cathodique est différent quelque soit la méthode : vga66 ou hdmi-scart
Par exemple je pense que tu essaies de modifier les fichiers de conf de RB sous windows... en inserant la carte SD. Malheureusement Windows ne verra que la partition de /boot en fat et pas les partitions recalbox et share en ext4 propre aux systèmes linux/unix. et malheureusement le fichier
recalbox.conf
à modifier se trouve sur la partition/share/system
-
@ian57 oui je sais tout ça même si ça fait un petit moment que j'avais laché l'affaire.
j'utilise winscp pour avoir accès à la partition de recalbox.
mais je ne sais pas pourquoi j'avais zappé certains trucs, comme quoi quand tu restes pas la tête dedans ça a vite fait de partir.
merci pour votre aide. -
@ian57
Bonjour, GENIAL !!!! Ca marche ;-), un grand grand merci, je vous êtes des super pro
Par contre l'image de certains jeux n'est pas complète, j'ai vu mais je ne sais plus oû que l'on définir la dénition pour chaque émulateur ...! -
@ian57
MAGNIFIQUE !!! -
@ian57 said in Recalbox sur TV CRT en RGB:
@retrobricoleur un debut de wiki https://github.com/recalbox/recalbox-os/wiki/Connect-your-recalbox-to-a-CRT-with-HDMI-and-SCART-(EN)
C'est dans le tuto il faut créer une config pour chaque système et ça rend super bien.
Ça rend bien sur ton écran ^_^
-
@Link71
merci de faire un effort de lecture par les liens fournis -
@acris
Oui, c'est vrai mais on est tellement impatient ... -
oui, et encore c'est une photo prise par un smartphone, les scalines sont superbes (aucun fitres biensûr)
-
@acris
Bonjour, je poste cette photo car je n'avais pas fait attention mais au démarrage de RECALBOX, il manque une petite partie de l'ecran en bas et sur la gauche du téléviseur.Idem pour tout les jeux que je lance. J'ai donc cherché dans les réglages le mode "costum" car j'ai vu des vidéos youtube de RECALBOX les tutos d'explication de tous les menus recalbox 4.1, mais dans les formats proposés (auto, 1/1, 16/9, etc) il n'y a pas ou plus le mode costum (j'ai la dernière version)