Overclocking Pi4 with recalbox 7

[sergioad]

This post is deleted!

[sergioad]

Ok friends, I fixed my ES hang ups, I dialed back my pi to 1950 MHz and incremented the over voltage to 9 while keeping GPU the same at 750 and this far I have not had any ES hang up.

If you want my troubleshooting script package from when ES was failing that much HERE it is.

I hope with the findings of the community something could be made to solve the over 2000 issues, I prefer by much Recalbox to the other solutions and not being tied by this bugs would be awesome.

Here are my settings:

arm_freq=1950
gpu_freq=750
over_voltage=9

[rollbrett]

@sergioad i'm not familiar with overclocking the pi 4, but in the documentation i found this about the overvoltage

CPU/GPU core voltage adjustment. The value should be in the range [-16, 8] which equates to the range [0.8V, 1.4V] with 0.025V steps. In other words, specifying -16 will give 0.8V as the GPU/core voltage, and specifying 8 will give 1.4V. For defaults see table below. Values above 6 are only allowed when force_turbo is specified: this sets the warranty bit if over_voltage_* is also set.

if this is correct, the maximum value of overvoltage is 8?

and what about force turbo do you have enable it?

[sergioad]

https://transfer.sh/NZCXK/recalbox-support-d3a5c3b5-7e27-a40d-d23e-2b454077d09e.tar.gz

[sergioad]

@rollbrett no, there are people running pis at over voltage 11, I use 9 on mine because the 8 GB model of the pi needs even more than the usual be 6 because it needs to acomidate the larger amount of RAM, in a 4 or 2 GB model 6 or 7 is more than enough, I have not enabled turbo

[LapinFou]

@sergioad said in Overclocking Pi4 with recalbox 7:

@rollbrett no, there are people running pis at over voltage 11, I use 9 on mine because the 8 GB model of the pi needs even more than the usual be 6 because it needs to acomidate the larger amount of RAM, in a 4 or 2 GB model 6 or 7 is more than enough, I have not enabled turbo

If you didn't enable the force_turbo, maybe your voltage 9 is seen as a 6?

[sergioad]

@LapinFou Ip sincerely doubt it

[Kruton]

I did not tested it by myself. But from official documentation and some forum posts by official staff, over_voltage bigger than 6 can be only activated when force_turbo is enabled. It is even possible to go over official limits by using parameter current_limit_override. But you are risking voiding your warranty if anything goes terribly wrong...

Source: https://www.raspberrypi.org/forums/viewtopic.php?f=29&t=6201&start=325#p170793

[deneme]

@ian57 said in Overclocking Pi4 with recalbox 7:

@phimjohn config.txt file only but be very carreful... be sure tu have a good cooling heatsink fan system, because Pi4 heats up a lot.

so whers this config.txt file in recalbox can you help me ???

[Zing]

@deneme Please read the topic, this is described a few posts above, you just have to read...

@Zing said in Overclocking Pi4 with recalbox 7:

To edit the config.txt file, you must connect via SSH:

• https://recalbox.gitbook.io/documentation/v/francais/tutoriels/systeme/modification/editer-le-fichier-config.txt

To login via SSH:

• https://recalbox.gitbook.io/documentation/v/francais/tutoriels/systeme/acces/acces-root-via-terminal
• https://recalbox.gitbook.io/documentation/v/francais/tutoriels/systeme/acces/acces-reseau-via-winscp

To access a partition in write mode:

• https://recalbox.gitbook.io/documentation/v/francais/tutoriels/systeme/acces/acceder-a-une-partition-en-ecriture