[RC3] Configuration GPIO

acris · 9 Apr 2019, 16:27

Bonjour @ViRuS-MaN
un bon formatage en régle avec uniquement les roms bios saves à sauvegarder car vue tous tes messages je pense que tu dois avoir des corruptions de fichiers.

Voici la procédure à suivre : https://forum.recalbox.com/topic/17011/a-lire-processus-de-mise-à-jour

ViRuS-MaN · 9 Apr 2019, 16:29

j ai deja fais un mise a jour clean j avais tout effacer mais je vais en refaire une et tester sur microsd et apres je testerais avec la cles usb et je vois dis quoi

ViRuS-MaN · 9 Apr 2019, 16:59

voila installation toute clean y a que ma carte microsd avec recalbox et rien d autre et mes manette gpio ne fonctionne pas fichier support ici je n ai mis que ma connextion wifi pour faire un fichier support et rien d autre

GDEHON · 9 Apr 2019, 19:24

active le GPIO (ON) via recalbox manager
Ensuite dans l'option des manettes, vérifie que tes boutons sont détectés...
Si c'est le cas configure boutons et joysticks pour les deux players puis pour chacun d'eux indique GPIO (#1 et #2)
Sinon redemarre et reçois ce GPIO sur ON dans Recalbox manager
Chez moi c'est ce GPIO ON dans Recalbox manager qui n'était pas pris en compte... Je ne sais pas pourquoi mais à force ça a fonctionné !

ian57 · 10 Apr 2019, 07:56

@ViRuS-MaN @GDEHON @acris J'ai fais un test à partir de la RC3 sur Pi3 ce matin :

mon recalbox.conf :

 # ------------ D2 - GPIO Controllers ------------ #
## GPIO Controllers
## enable controllers on GPIO with mk_arcarde_joystick_rpi (0,1)
controllers.gpio.enabled=1
## mk_gpio arguments, map=1 for one controller, map=1,2 for 2 (map=1,map=1,2)
controllers.gpio.args=map=1,2

manette free connectée + clavier pour être a peu près dans les mêmes conditions. reboot et ensuite configuration sans soucis de mon panel GPIO

du coup je vois pas trop d'ou peut venir le soucis...

GDEHON · 10 Apr 2019, 08:58

Pour ma part j'avais le même soucis de non reconnaissance du GPIO...
Je l'activais par Recalbox Manager mais visiblement ce n'était pas reconnu en ON...
Apres plusieurs essais et des passages de l'ancienne version (GPIO fonctionnel) à la RC (2 pour moi lors de ce problème), de OFF/ON sur Recalbox Manager, ça a finalement fonctionné...
Ensuite j'ai fait comme sur tes photos pour configuration et choix du GPIO/player
Par contre je n'ai pas compris pourquoi ça ne reconnaissait pas le GPIO! Ni ce qui a résolu le problème...

ian57 · 10 Apr 2019, 09:49

@GDEHON peut être un petit soucis d'enregistrement du recalbox.conf. Il me semble que sur la RC2 j'ai été obligé de l'activé 2x.
par contre je passe toujours par ssh jamais par l'interface web

acris · 10 Apr 2019, 09:56

@ian57
l archive de support de virusman indique que les gpio sont activées

ViRuS-MaN · 10 Apr 2019, 11:14

oui tout est bon mais si je mets pas le inputconfig de @GDEHON je ne vois pas les 3 manettes , la sans rien changer je vois une manette connecter

ian57 · 10 Apr 2019, 11:24

@ViRuS-MaN peux tu poster le inputconfig de @GDEHON stp;;

pour que tu puisse comparer voici des eléments. c'est ce que j'ai sur ma config

dmesg

 [    5.681446] mk_arcade_joystick_rpi: loading out-of-tree module taints kernel.
[    5.682964] mk_arcade_joystick_rpi: pad type : 1
[    5.682976] mk_arcade_joystick_rpi: pad type : 1
[    5.682994] GPIO = 4
[    5.682997] GPIO = 17
[    5.682999] GPIO = 27
[    5.683001] GPIO = 22
[    5.683005] GPIO = 10
[    5.683007] GPIO = 9
[    5.683009] GPIO = 25
[    5.683011] GPIO = 24
[    5.683013] GPIO = 23
[    5.683015] GPIO = 18
[    5.683018] GPIO = 15
[    5.683021] GPIO = 14
[    5.683024] GPIO = 2
[    5.683048] GPIO configured for pad0
[    5.683607] input: GPIO Controller 1 as /devices/virtual/input/input1
[    5.683883] mk_arcade_joystick_rpi: pad type : 2
[    5.683885] mk_arcade_joystick_rpi: pad type : 2
[    5.683898] GPIO = 11
[    5.683901] GPIO = 5
[    5.683903] GPIO = 6
[    5.683905] GPIO = 13
[    5.683907] GPIO = 19
[    5.683910] GPIO = 26
[    5.683912] GPIO = 21
[    5.683915] GPIO = 20
[    5.683917] GPIO = 16
[    5.683919] GPIO = 12
[    5.683921] GPIO = 7
[    5.683923] GPIO = 8
[    5.683925] GPIO = 3
[    5.683948] GPIO configured for pad1
[    5.685031] input: GPIO Controller 2 as /devices/virtual/input/input2

es_log

[2019/04/10 09:37:45.028] (INFO ) : Added unconfigured joystick GPIO Controller 1 (GUID: 15000000010000000100000000010000, instance ID: 0, device index: 0).
[2019/04/10 09:37:45.030] (INFO ) : Added unconfigured joystick GPIO Controller 2 (GUID: 15000000010000000200000000010000, instance ID: 1, device index: 1).

es_input.cfg

 	<inputConfig type="joystick" deviceName="GPIO Controller 2" deviceGUID="15000000010000000200000000010000" deviceNbAxes="2" deviceNbHats="0" deviceNbButtons="9">
		<input name="a" type="button" id="0" value="1" code="304" />
		<input name="b" type="button" id="1" value="1" code="305" />
		<input name="down" type="axis" id="1" value="1" code="1" />
		<input name="hotkey" type="button" id="8" value="1" code="316" />
		<input name="left" type="axis" id="0" value="-1" code="0" />
		<input name="pagedown" type="button" id="5" value="1" code="311" />
		<input name="pageup" type="button" id="4" value="1" code="310" />
		<input name="right" type="axis" id="0" value="1" code="0" />
		<input name="select" type="button" id="6" value="1" code="314" />
		<input name="start" type="button" id="7" value="1" code="315" />
		<input name="up" type="axis" id="1" value="-1" code="1" />
		<input name="x" type="button" id="2" value="1" code="307" />
		<input name="y" type="button" id="3" value="1" code="308" />
	</inputConfig>
	<inputConfig type="joystick" deviceName="DragonRise Inc.   Generic   USB  Joystick  " deviceGUID="03000000790000000600000010010000" deviceNbAxes="5" deviceNbHats="1" deviceNbBu
ttons="12">
		<input name="a" type="button" id="1" value="1" code="289" />
		<input name="b" type="button" id="2" value="1" code="290" />
		<input name="down" type="hat" id="0" value="4" code="16" />
		<input name="hotkey" type="button" id="8" value="1" code="296" />
		<input name="joystick1left" type="axis" id="0" value="-1" code="0" />
		<input name="joystick1up" type="axis" id="1" value="-1" code="1" />
		<input name="joystick2left" type="axis" id="3" value="-1" code="3" />
		<input name="joystick2up" type="axis" id="4" value="-1" code="5" />
		<input name="l2" type="button" id="6" value="1" code="294" />
		<input name="left" type="hat" id="0" value="8" code="16" />
		<input name="pagedown" type="button" id="5" value="1" code="293" />
		<input name="pageup" type="button" id="4" value="1" code="292" />
		<input name="r2" type="button" id="7" value="1" code="295" />
		<input name="right" type="hat" id="0" value="2" code="16" />
		<input name="select" type="button" id="8" value="1" code="296" />
		<input name="start" type="button" id="9" value="1" code="297" />
		<input name="up" type="hat" id="0" value="1" code="16" />
		<input name="x" type="button" id="0" value="1" code="288" />
		<input name="y" type="button" id="3" value="1" code="291" />
	</inputConfig>
	<inputConfig type="joystick" deviceName="GPIO Controller 1" deviceGUID="15000000010000000100000000010000" deviceNbAxes="2" deviceNbHats="0" deviceNbButtons="9">
		<input name="a" type="button" id="0" value="1" code="304" />
		<input name="b" type="button" id="1" value="1" code="305" />
		<input name="down" type="axis" id="1" value="1" code="1" />
		<input name="hotkey" type="button" id="8" value="1" code="316" />
		<input name="left" type="axis" id="0" value="-1" code="0" />
		<input name="pagedown" type="button" id="5" value="1" code="311" />
		<input name="pageup" type="button" id="4" value="1" code="310" />
		<input name="right" type="axis" id="0" value="1" code="0" />
		<input name="select" type="button" id="6" value="1" code="314" />
		<input name="start" type="button" id="7" value="1" code="315" />
		<input name="up" type="axis" id="1" value="-1" code="1" />
		<input name="x" type="button" id="2" value="1" code="307" />
		<input name="y" type="button" id="3" value="1" code="308" />
	</inputConfig>

ev_test

# evtest
No device specified, trying to scan all of /dev/input/event*
Available devices:
/dev/input/event0:	CHICONY HP Basic USB Keyboard
/dev/input/event1:	GPIO Controller 1
/dev/input/event2:	GPIO Controller 2
/dev/input/event3:	DragonRise Inc.   Generic   USB  Joystick  
Select the device event number [0-3]: 1
Input driver version is 1.0.1
Input device ID: bus 0x15 vendor 0x1 product 0x1 version 0x100
Input device name: "GPIO Controller 1"
Supported events:
  Event type 0 (EV_SYN)
  Event type 1 (EV_KEY)
    Event code 304 (BTN_SOUTH)
    Event code 305 (BTN_EAST)
    Event code 307 (BTN_NORTH)
    Event code 308 (BTN_WEST)
    Event code 310 (BTN_TL)
    Event code 311 (BTN_TR)
    Event code 314 (BTN_SELECT)
    Event code 315 (BTN_START)
    Event code 316 (BTN_MODE)
  Event type 3 (EV_ABS)
    Event code 0 (ABS_X)
      Value      0
      Min       -1
      Max        1
    Event code 1 (ABS_Y)
      Value      0
      Min       -1
      Max        1
Properties:
Testing ... (interrupt to exit)
Event: time 1554895427.113731, type 3 (EV_ABS), code 1 (ABS_Y), value -1
Event: time 1554895427.113731, -------------- SYN_REPORT ------------
Event: time 1554895427.233746, type 3 (EV_ABS), code 1 (ABS_Y), value 0
Event: time 1554895427.233746, -------------- SYN_REPORT ------------
Event: time 1554895427.593773, type 3 (EV_ABS), code 1 (ABS_Y), value 1
Event: time 1554895427.593773, -------------- SYN_REPORT ------------
Event: time 1554895427.693787, type 3 (EV_ABS), code 1 (ABS_Y), value 0
Event: time 1554895427.693787, -------------- SYN_REPORT ------------
Event: time 1554895428.033742, type 3 (EV_ABS), code 0 (ABS_X), value -1
Event: time 1554895428.033742, -------------- SYN_REPORT ------------
Event: time 1554895428.133745, type 3 (EV_ABS), code 0 (ABS_X), value 0
Event: time 1554895428.133745, -------------- SYN_REPORT ------------
Event: time 1554895428.413740, type 3 (EV_ABS), code 0 (ABS_X), value 1
Event: time 1554895428.413740, -------------- SYN_REPORT ------------
Event: time 1554895428.533749, type 3 (EV_ABS), code 0 (ABS_X), value 0
Event: time 1554895428.533749, -------------- SYN_REPORT ------------
Event: time 1554895429.453739, type 1 (EV_KEY), code 305 (BTN_EAST), value 1
Event: time 1554895429.453739, -------------- SYN_REPORT ------------
Event: time 1554895429.553753, type 1 (EV_KEY), code 305 (BTN_EAST), value 0
Event: time 1554895429.553753, -------------- SYN_REPORT ------------
Event: time 1554895429.773753, type 1 (EV_KEY), code 304 (BTN_SOUTH), value 1
Event: time 1554895429.773753, -------------- SYN_REPORT ------------
Event: time 1554895429.893764, type 1 (EV_KEY), code 304 (BTN_SOUTH), value 0
Event: time 1554895429.893764, -------------- SYN_REPORT ------------
Event: time 1554895430.153744, type 1 (EV_KEY), code 311 (BTN_TR), value 1
Event: time 1554895430.153744, -------------- SYN_REPORT ------------
Event: time 1554895430.273760, type 1 (EV_KEY), code 311 (BTN_TR), value 0
Event: time 1554895430.273760, -------------- SYN_REPORT ------------
Event: time 1554895430.513745, type 1 (EV_KEY), code 310 (BTN_TL), value 1
Event: time 1554895430.513745, -------------- SYN_REPORT ------------
Event: time 1554895430.633743, type 1 (EV_KEY), code 310 (BTN_TL), value 0
Event: time 1554895430.633743, -------------- SYN_REPORT ------------
Event: time 1554895430.873777, type 1 (EV_KEY), code 307 (BTN_NORTH), value 1
Event: time 1554895430.873777, -------------- SYN_REPORT ------------
Event: time 1554895430.953753, type 1 (EV_KEY), code 307 (BTN_NORTH), value 0
Event: time 1554895430.953753, -------------- SYN_REPORT ------------
Event: time 1554895431.253738, type 1 (EV_KEY), code 308 (BTN_WEST), value 1
Event: time 1554895431.253738, -------------- SYN_REPORT ------------
Event: time 1554895431.353748, type 1 (EV_KEY), code 308 (BTN_WEST), value 0
Event: time 1554895431.353748, -------------- SYN_REPORT ------------
Event: time 1554895431.733743, type 1 (EV_KEY), code 316 (BTN_MODE), value 1
Event: time 1554895431.733743, -------------- SYN_REPORT ------------
Event: time 1554895431.833740, type 1 (EV_KEY), code 316 (BTN_MODE), value 0
Event: time 1554895431.833740, -------------- SYN_REPORT ------------
Event: time 1554895432.053740, type 1 (EV_KEY), code 314 (BTN_SELECT), value 1
Event: time 1554895432.053740, -------------- SYN_REPORT ------------
Event: time 1554895432.153745, type 1 (EV_KEY), code 314 (BTN_SELECT), value 0
Event: time 1554895432.153745, -------------- SYN_REPORT ------------
Event: time 1554895432.333744, type 1 (EV_KEY), code 315 (BTN_START), value 1
Event: time 1554895432.333744, -------------- SYN_REPORT ------------
Event: time 1554895432.453742, type 1 (EV_KEY), code 315 (BTN_START), value 0
Event: time 1554895432.453742, -------------- SYN_REPORT ------------

GDEHON · 10 Apr 2019, 12:27

@ian57 said in [RC3] Configuration GPIO:

@GDEHON peut être un petit soucis d'enregistrement du recalbox.conf. Il me semble que sur la RC2 j'ai été obligé de l'activé 2x.
par contre je passe toujours par ssh jamais par l'interface web

Ok pour le problème d'enregistrement...
Par contre pour le ssh c'est putty ou juste winscp ?

@acris said in [RC3] Configuration GPIO:

@ian57
l archive de support de virusman indique que les gpio sont activées

Donc ce n'est pas le même soucis que moi c'est ça ?

@ian57 said in [RC3] Configuration GPIO:

@ViRuS-MaN peux tu poster le inputconfig de @GDEHON stp;;

Je l'ai posté [ici]https://forum.recalbox.com/topic/15946/rc-version-support-archives-with-pad-configurations-needed/9)

Voici ma config via GPIO (boutons hotkey en place)
https://file.ac/NLBMc8j36wU/

 <inputConfig type="joystick" deviceName="GPIO Controller 1" deviceGUID="15000000010000000100000000010000" deviceNbAxes="2" deviceNbHats="0" deviceNbButtons="9">
<input name="a" type="button" id="1" value="1" code="305" />
	<input name="b" type="button" id="0" value="1" code="304" />
	<input name="down" type="axis" id="1" value="1" code="1" />
	<input name="hotkey" type="button" id="8" value="1" code="316" />
	<input name="left" type="axis" id="0" value="-1" code="0" />
	<input name="pagedown" type="button" id="5" value="1" code="311" />
	<input name="pageup" type="button" id="4" value="1" code="310" />
	<input name="right" type="axis" id="0" value="1" code="0" />
	<input name="select" type="button" id="6" value="1" code="314" />
	<input name="start" type="button" id="7" value="1" code="315" />
	<input name="up" type="axis" id="1" value="-1" code="1" />
	<input name="x" type="button" id="2" value="1" code="307" />
	<input name="y" type="button" id="3" value="1" code="308" />
</inputConfig>
<inputConfig type="joystick" deviceName="GPIO Controller 2" deviceGUID="15000000010000000200000000010000" deviceNbAxes="2" deviceNbHats="0" deviceNbButtons="9">
	<input name="a" type="button" id="1" value="1" code="305" />
	<input name="b" type="button" id="0" value="1" code="304" />
	<input name="down" type="axis" id="1" value="1" code="1" />
	<input name="hotkey" type="button" id="8" value="1" code="316" />
	<input name="left" type="axis" id="0" value="-1" code="0" />
	<input name="pagedown" type="button" id="5" value="1" code="311" />
	<input name="pageup" type="button" id="4" value="1" code="310" />
	<input name="right" type="axis" id="0" value="1" code="0" />
	<input name="select" type="button" id="6" value="1" code="314" />
	<input name="start" type="button" id="7" value="1" code="315" />
	<input name="up" type="axis" id="1" value="-1" code="1" />
	<input name="x" type="button" id="2" value="1" code="307" />
	<input name="y" type="button" id="3" value="1" code="308" />
</inputConfig>

ViRuS-MaN · 10 Apr 2019, 14:22

voila mes configuration a moi dans emulationstation configuration desole mais je n arrive pas a faire ce que vous faites pour les afficher

ian57 · 10 Apr 2019, 14:56

@ViRuS-MaN je n'ai rien vu de particulier mis à part que ton es_input ne contient pas les gpio. mais normalement c'est pas un soucis.
La version 6.0 sort ce vendredi normalement. je viens de la tester et pas de soucis avec mes GPIO.
Attends 2 jours et on refara des tests avec cette nouvelle version

ViRuS-MaN · 10 Apr 2019, 15:15

c est ce que je vais faire et on veras bien ce que ca va donner , la tester la rc3 c est deja top car elle marche tres bien

ViRuS-MaN · 13 Apr 2019, 14:37

@ian57 j ai refait un sujet [6.0] probleme gpio et j ai toujours ce probleme

[RC3] Configuration GPIO

Want to support us ?

81
Online

98.0k
Users

28.0k
Topics

186.9k
Posts

	# ------------ D2 - GPIO Controllers ------------ #
	## GPIO Controllers
	## enable controllers on GPIO with mk_arcarde_joystick_rpi (0,1)
	controllers.gpio.enabled=1
	## mk_gpio arguments, map=1 for one controller, map=1,2 for 2 (map=1,map=1,2)
	controllers.gpio.args=map=1,2

	[ 5.681446] mk_arcade_joystick_rpi: loading out-of-tree module taints kernel.
	[ 5.682964] mk_arcade_joystick_rpi: pad type : 1
	[ 5.682976] mk_arcade_joystick_rpi: pad type : 1
	[ 5.682994] GPIO = 4
	[ 5.682997] GPIO = 17
	[ 5.682999] GPIO = 27
	[ 5.683001] GPIO = 22
	[ 5.683005] GPIO = 10
	[ 5.683007] GPIO = 9
	[ 5.683009] GPIO = 25
	[ 5.683011] GPIO = 24
	[ 5.683013] GPIO = 23
	[ 5.683015] GPIO = 18
	[ 5.683018] GPIO = 15
	[ 5.683021] GPIO = 14
	[ 5.683024] GPIO = 2
	[ 5.683048] GPIO configured for pad0
	[ 5.683607] input: GPIO Controller 1 as /devices/virtual/input/input1
	[ 5.683883] mk_arcade_joystick_rpi: pad type : 2
	[ 5.683885] mk_arcade_joystick_rpi: pad type : 2
	[ 5.683898] GPIO = 11
	[ 5.683901] GPIO = 5
	[ 5.683903] GPIO = 6
	[ 5.683905] GPIO = 13
	[ 5.683907] GPIO = 19
	[ 5.683910] GPIO = 26
	[ 5.683912] GPIO = 21
	[ 5.683915] GPIO = 20
	[ 5.683917] GPIO = 16
	[ 5.683919] GPIO = 12
	[ 5.683921] GPIO = 7
	[ 5.683923] GPIO = 8
	[ 5.683925] GPIO = 3
	[ 5.683948] GPIO configured for pad1
	[ 5.685031] input: GPIO Controller 2 as /devices/virtual/input/input2

	<inputConfig type="joystick" deviceName="GPIO Controller 2" deviceGUID="15000000010000000200000000010000" deviceNbAxes="2" deviceNbHats="0" deviceNbButtons="9">
	<input name="a" type="button" id="0" value="1" code="304" />
	<input name="b" type="button" id="1" value="1" code="305" />
	<input name="down" type="axis" id="1" value="1" code="1" />
	<input name="hotkey" type="button" id="8" value="1" code="316" />
	<input name="left" type="axis" id="0" value="-1" code="0" />
	<input name="pagedown" type="button" id="5" value="1" code="311" />
	<input name="pageup" type="button" id="4" value="1" code="310" />
	<input name="right" type="axis" id="0" value="1" code="0" />
	<input name="select" type="button" id="6" value="1" code="314" />
	<input name="start" type="button" id="7" value="1" code="315" />
	<input name="up" type="axis" id="1" value="-1" code="1" />
	<input name="x" type="button" id="2" value="1" code="307" />
	<input name="y" type="button" id="3" value="1" code="308" />
	</inputConfig>
	<inputConfig type="joystick" deviceName="DragonRise Inc. Generic USB Joystick " deviceGUID="03000000790000000600000010010000" deviceNbAxes="5" deviceNbHats="1" deviceNbBu
	ttons="12">
	<input name="a" type="button" id="1" value="1" code="289" />
	<input name="b" type="button" id="2" value="1" code="290" />
	<input name="down" type="hat" id="0" value="4" code="16" />
	<input name="hotkey" type="button" id="8" value="1" code="296" />
	<input name="joystick1left" type="axis" id="0" value="-1" code="0" />
	<input name="joystick1up" type="axis" id="1" value="-1" code="1" />
	<input name="joystick2left" type="axis" id="3" value="-1" code="3" />
	<input name="joystick2up" type="axis" id="4" value="-1" code="5" />
	<input name="l2" type="button" id="6" value="1" code="294" />
	<input name="left" type="hat" id="0" value="8" code="16" />
	<input name="pagedown" type="button" id="5" value="1" code="293" />
	<input name="pageup" type="button" id="4" value="1" code="292" />
	<input name="r2" type="button" id="7" value="1" code="295" />
	<input name="right" type="hat" id="0" value="2" code="16" />
	<input name="select" type="button" id="8" value="1" code="296" />
	<input name="start" type="button" id="9" value="1" code="297" />
	<input name="up" type="hat" id="0" value="1" code="16" />
	<input name="x" type="button" id="0" value="1" code="288" />
	<input name="y" type="button" id="3" value="1" code="291" />
	</inputConfig>
	<inputConfig type="joystick" deviceName="GPIO Controller 1" deviceGUID="15000000010000000100000000010000" deviceNbAxes="2" deviceNbHats="0" deviceNbButtons="9">
	<input name="a" type="button" id="0" value="1" code="304" />
	<input name="b" type="button" id="1" value="1" code="305" />
	<input name="down" type="axis" id="1" value="1" code="1" />
	<input name="hotkey" type="button" id="8" value="1" code="316" />
	<input name="left" type="axis" id="0" value="-1" code="0" />
	<input name="pagedown" type="button" id="5" value="1" code="311" />
	<input name="pageup" type="button" id="4" value="1" code="310" />
	<input name="right" type="axis" id="0" value="1" code="0" />
	<input name="select" type="button" id="6" value="1" code="314" />
	<input name="start" type="button" id="7" value="1" code="315" />
	<input name="up" type="axis" id="1" value="-1" code="1" />
	<input name="x" type="button" id="2" value="1" code="307" />
	<input name="y" type="button" id="3" value="1" code="308" />
	</inputConfig>

	<inputConfig type="joystick" deviceName="GPIO Controller 1" deviceGUID="15000000010000000100000000010000" deviceNbAxes="2" deviceNbHats="0" deviceNbButtons="9">
	<input name="a" type="button" id="1" value="1" code="305" />
	<input name="b" type="button" id="0" value="1" code="304" />
	<input name="down" type="axis" id="1" value="1" code="1" />
	<input name="hotkey" type="button" id="8" value="1" code="316" />
	<input name="left" type="axis" id="0" value="-1" code="0" />
	<input name="pagedown" type="button" id="5" value="1" code="311" />
	<input name="pageup" type="button" id="4" value="1" code="310" />
	<input name="right" type="axis" id="0" value="1" code="0" />
	<input name="select" type="button" id="6" value="1" code="314" />
	<input name="start" type="button" id="7" value="1" code="315" />
	<input name="up" type="axis" id="1" value="-1" code="1" />
	<input name="x" type="button" id="2" value="1" code="307" />
	<input name="y" type="button" id="3" value="1" code="308" />
	</inputConfig>
	<inputConfig type="joystick" deviceName="GPIO Controller 2" deviceGUID="15000000010000000200000000010000" deviceNbAxes="2" deviceNbHats="0" deviceNbButtons="9">
	<input name="a" type="button" id="1" value="1" code="305" />
	<input name="b" type="button" id="0" value="1" code="304" />
	<input name="down" type="axis" id="1" value="1" code="1" />
	<input name="hotkey" type="button" id="8" value="1" code="316" />
	<input name="left" type="axis" id="0" value="-1" code="0" />
	<input name="pagedown" type="button" id="5" value="1" code="311" />
	<input name="pageup" type="button" id="4" value="1" code="310" />
	<input name="right" type="axis" id="0" value="1" code="0" />
	<input name="select" type="button" id="6" value="1" code="314" />
	<input name="start" type="button" id="7" value="1" code="315" />
	<input name="up" type="axis" id="1" value="-1" code="1" />
	<input name="x" type="button" id="2" value="1" code="307" />
	<input name="y" type="button" id="3" value="1" code="308" />
	</inputConfig>

[RC3] Configuration GPIO

Want to support us ?

81Online

98.0kUsers

28.0kTopics

186.9kPosts

81
Online

98.0k
Users

28.0k
Topics

186.9k
Posts