[SOFT] dynquee: dynamic marquee for Recalbox

[poppadum]

@leew said in [SOFT] dynquee: dynamic marquee for Recalbox:

*the pictures that should display on the marquee are shown on the main screen on and off.

On a Pi, both displays share the same framebuffer so usually the dynquee display is briefly visible on the main screen when an emulator launches or exits. A bit annoying, but we can't do much about it.

*my display is 1920x360 and i have set this up correctly

OK, that's good; just to double check, if you run the commandfbset it should confirm that the framebuffer is indeed set to 1920x360.

still has black bars top and bottom of the screen

What size of the images are you using for your marquee? 1920x360 is a common size so I suggest you start from an existing set (see e.g. the Super Pixelcade set).

To check how your images display on the marquee, stop dynquee with
/etc/init.d/S32dynquee stop
then try displaying one of your marquee images with e.g.
fbv2 /recalbox/share/dynquee/media/mame/1942.jpg (replace with a path to a marquee image).

You can experiment with the --enlarge and --ignore-aspect options, but personally I just resize all my marquee images to be 360 pixels high (my marquee is also 1920x360).

*The dynquee picture displays on the marquee for a very short time and then shows a recalbox picture with the 4 pacmen

I'm not 100% sure why that is. Make sure that in your /etc/recalbox.conf (section J) you have
system.secondminitft.enabled=0
or the line commented out.

You could also try disabling the intro video with
system.splash.length=0
(section A)

[leew]

@poppadum Thanks for the very detailed response and the time you have taken out of your free time to respond to me. Firstly i am a very inexperienced on the software side, but i love to learn. Unfortunately that might generate a lot more questions. I hope you don't mind and let me know if i become a pain.

I didn't know i needed to add any images, it just seemed to be working out of the box so to speak. I will look at the guide and see if i can add some images with the correct size and see if that works.

i don't have a lot of free time this week so there might be a delay getting back to you with questions or to let you know it is working

Thanks again and thanks for putting this project out there for everyone to use.

Lee

[poppadum]

@leew said in [SOFT] dynquee: dynamic marquee for Recalbox:

@poppadum Thanks for the very detailed response and the time you have taken out of your free time to respond to me. Firstly i am a very inexperienced on the software side, but i love to learn. Unfortunately that might generate a lot more questions. I hope you don't mind and let me know if i become a pain.

No problem at all - I'll try my best to help.

I didn't know i needed to add any images, it just seemed to be working out of the box so to speak. I will look at the guide and see if i can add some images with the correct size and see if that works.

It can use scraped images as a last resort, but I always intended to use images sized roughly to my marquee screen, so I just assumed everybody else would do too.

The are some docs in English (no other languages yet but I'm happy to add them if anyone wants to translate): see the README and probably the config guide.

[leew]

@poppadum
I have uploaded some images with the correct aspect and i still see black bars top and bottom. with a very o

running the command fbset comes back with this

Not sure where to go from here?? Any help greatly received.

[leew]

@poppadum ok so some more playing

by un hashing this line i got the resolution to show 1920x360 but it now pushes the image to the top of the screen
framebuffer_resolution_cmd = /usr/sbin/fbset -g ${global:marquee_width} ${global:marquee_height} ${global:marquee_width} ${global:marquee_height} 16

this is how a 1920x360 image is showing

frustration is that the start up video is running full screen on this screen.

[poppadum]

@leew said in [SOFT] dynquee: dynamic marquee for Recalbox:

@poppadum ok so some more playing

by un hashing this line i got the resolution to show 1920x360 but it now pushes the image to the top of the screen
framebuffer_resolution_cmd = /usr/sbin/fbset -g ${global:marquee_width} ${global:marquee_height} ${global:marquee_width} ${global:marquee_height} 16

That looks good - I get exactly the same output.

this is how a 1920x360 image is showing

Bizarre: that looks like it's taking up exactly one-third of the height which is what it would do if it thought the resolution was 1920x1080.

Could you try stopping dynquee with
/etc/init.d/S32dynquee stop
double check your framebuffer resolution with fbset
then manually displaying that image with
fbv2 path/to/your/image

You could also try with another 1920x360 image such as:
https://virginia.byf.org/wp-content/uploads/2017/03/pexels-photo-358483-1920x360.jpg

[leew]

@poppadum Thanks for your help on this. it seems to be an issue with the driver board for the screen. purchased another board and this seems to fix the image size issue but has created a white line down the middle of the screen. It seems i have two faulty boards! Have emailed the manufacturer to see if they can help.

[daniel6984]

@poppadum bonjour,

Sur la version 9.1 de recalbox , il y a la possibilité d'afficher des systèmes virtuels par genre en passant par les paramètres avancés\systèmes virtuels\systèmes virtuels par genre.

Quand je choisis par exemple le systèmes virtuels shoot em up, il apparait bien sur le menu de navigation mais j'arrive pas a afficher le marquée, comment dois-je renommé l'image .logo.png pour qu'il apparaissent ?
Merci par avance.
Cordialement

[poppadum]

@daniel6984 said in [SOFT] dynquee: dynamic marquee for Recalbox:

@poppadum Quand je choisis par exemple le systèmes virtuels shoot em up, il apparait bien sur le menu de navigation mais j'arrive pas a afficher le marquée, comment dois-je renommé l'image .logo.png pour qu'il apparaissent ?

Il faut nommer les fichiers <SystemId>.<quelque-chose>.png/.jpg
par exemple: actionshootemup.01.png

Liste des SystemIds pour les systèmes virtuels:

favorites
lightgun
multiplayer
action
actionplatformer
actionplatformshooter
actionfirstpersonshooter
actionshootemup
actionshootwithgun
actionfighting
actionbeatemup
actionstealth
actionbattleroyale
actionrythm
adventure
adventuretext
adventuregraphics
adventurevisualnovels
adventureinteractivemovie
adventurerealtime3d
adventuresurvivalhorror
rpg
rpgaction
rpgmmo
rpgdungeoncrawler
rpgtactical
rpgjapanese
rpgfirstpersonpartybased
simulation
simulationbuildandmanagement
simulationlife
simulationfishandhunt
simulationvehicle
simulationscifi
strategy
strategy4x
strategyartillery
strategyautobattler
strategymoba
strategyrts
strategytbs
strategytowerdefense
strategywargame
sports
sportracing
sportsimulation
sportcompetitive
sportfight
pinball
board
casual
digitalcard
puzzleandlogic
party
trivia
casino
compilation
demoscene
educative

[daniel6984]

@poppadum said in [SOFT] dynquee: dynamic marquee for Recalbox:

actionshootemup

Merci infiniment je comprend pourquoi ça ne s'affichai pas , je mettais action-shootemup a la place de actionshootemup

[daniel6984]

@POPPADUM Bonjour,

J'ai une question pour un ami, il a un rpi4 avec un RGB DUAL qui ce branche via les GPIO, il est brancher en péritel sur une petite télévision crt 14 pouces d'une résolution de 320x240 fréquence 15khz, il a voulu tester les marquees sur un écran lcd brancher en hdmi , mais les images apparaisse que sur la télévision crt, avez une astuce pour faire apparaitre les images marquee sur le lcd ?
Je vous remercie

[poppadum]

@daniel6984 said in [SOFT] dynquee: dynamic marquee for Recalbox:

il a un rpi4 avec un RGB DUAL qui ce branche via les GPIO... il a voulu tester les marquees sur un écran lcd brancher en hdmi, mais les images apparaisse que sur la télévision crt

Pour le raspberry pi 4, les deux écrans HDMI partagent le framebuffer, mais il semble qu'avec un RGB Dual le framebuffer ne s'affiche que sur le CRT.

Pour Recalbox PC dynquee utilise mpv --screen=2 pour afficher les images sur l'écran 2. Pourrait-il tester si cela fonctionne avec:

mpv --screen=2 --loop <image.png>

[daniel6984]

@poppadum Bonjour,
merci beaucoup de nous avoir repondu.
Nous voulons tester la ligne que tu nous a donnée, nous somme que sur rpi4 , dans le .ini , ou faut-il insérer la ligne mpv --screen=2 --loop <image.png> ?
Merci encor pour ton aide

[poppadum]

@daniel6984 Pour tester c'est plus facile d'accéder au cli et d'entrer

mpv --screen=2 --loop /recalbox/share/dynquee/media/startup/startup.01.png

Ou modifiez dynquee.ini lignes 169-170:

viewer = /usr/bin/mpv
viewer_opts = --screen=2 --loop {file}

[daniel6984]

@poppadum Bonjour
Merci beaucoup pour l'aide ,
ont a essayer par le .ini, ont a bien l'image du startup sur l'écran lcd mais plus d'image sur le CRT et aucun mouvement d'image n'apparait quand ont va de droite a gauche, l'image startup reste fixe.

[poppadum]

@daniel6984 said in [SOFT] dynquee: dynamic marquee for Recalbox:

aucun mouvement d'image n'apparait quand ont va de droite a gauche, l'image startup reste fixe

J'ai oublié qu'il faut aussi modifier (dynquee.ini ligne 174):

terminate_viewer = yes

mais plus d'image sur le CRT

Tu vois rien sur le CRT, ni les images de marquee ni les jeux?

[daniel6984]

@poppadum Bonjour,
Avec la ligne terminate_viewer = yes, il y a bien l'image des marquees que sur le crt pendant le chargement du jeux, mais rien sur l'écran lcd

[Tuko]

@leew

Hi, I also had the same problem.
It seems that the ultra wide screen is not really 1920 x 360. I solved it by setting it to 1920 x 1080 by editing lines 14, 15 and 170

13  # marquee resolution: change to suit your marquee screen
14  marquee_width = 1920
15  marquee_height = 1080

168   # path to image viewer executable & options
169   viewer = /usr/bin/fbv2
170   viewer_opts = --noinfo --enlarge --ignore-aspect {file}

Let me know if you solve at least partially

[poppadum]

@daniel6984 said in [SOFT] dynquee: dynamic marquee for Recalbox:

Avec la ligne terminate_viewer = yes, il y a bien l'image des marquees que sur le crt pendant le chargement du jeux, mais rien sur l'écran lcd

Hmm

Et aussi rien sur l'écran lcd avec

viewer = /usr/bin/mpv
viewer_opts = --screen=1 --loop {file}

?

[toniosj]

@poppadum Awesome!!!

Where did you buy your LCD marquee? What dimensions?