Retour 7.2.2 sur XU4
-
Bonjour,
Voici la marche à suivre pour activer l'écran OGST:
- il faut éditer le fichier
recalbox.confqui se trouve sur la partition SHARE dans le répertoiresystem.
Dans ce fichier, il faut modifier ces paramètres:
system.secondminitft.enabled=1 system.secondminitft.type=overlay system.secondminitft.resolution=240pPrenez soin d'enlever les ; qui se trouveraient devant chaque ligne
-
si vous avez procédé à une installation fraîche de la version 7.2.2, vous pouvez passer directement à l'étape 3. Pour les personnes qui ont effectué une mise à jour, il faudra copier 2 fichiers avant de procéder à l'étape 3: dans la partition RECALBOX, copier le fichier
boot.ini.sampleenboot.ini. Prenez soin de vérifier la configuration écran (les lignes qui commencent par setenv). En général, il suffit de d'enlever le # qui se trouve devant la résolution que vous désirez. (Notez qu'il est possible de commenter toutes les optionssetenv videoconfig, le XU4 prendra tout seul la meilleure résolution).
Copier aussi le fichierconfig.ini.sampleenconfig.ini. -
éditer ensuite le fichier
config.iniqui se trouve sur la partition RECALBOX.
Il suffit juste d'enlever le ; de la ligne
overlay_profile=hktft_cs_ogst- redémarrer le XU4.
Le wiki sera modifié pour prendre en compte ce nouveau fonctionnement.
David
- il faut éditer le fichier
-
@cedric-debuiselle il semblerait selon certain retour que en eMMC cela ne fonctionne pas .... mais de mon coté en micro SD cela ne fonctionne pas non plus
-
Merci pour les lignes je vais tester ça demain
je vais essayé sur une micro SD pour voir si y a du changement
-
Salut,
En effet, les vidéos saccadent. J'ai isolé d'où cela vient. Ça sera corrigé dans la prochaine version.
Petit aparté, le xu4 n'est pas une plateforme laissée à l'abandon. Bien au contraire, nous essayons de la faire progresser au fil des releases de Recalbox. La complexité à maintenir en vie la plateforme vient du fait que le constructeur ne fait pas évoluer les softs qui sont utiles pour la plateforme (le noyau Linux pour ne citer que lui) et il faut attendre des initiatives de la communauté pour voir des avancées. Malheureusement, elles ne sont pas toutes parfaites et il faut parfois adapter des bouts de code.
David
-
@loli72 said in Retour 7.2.2 sur XU4:
@manitou Au cas où je te laisse le contenu complet de mon recalbox.conf et du config.ini en 7.2.2. Après je vois plus quoi faire.
recalbox.conf
# System Variable # You can configure your recalbox from here # To set a variable, remove the first ; on the line # NOTE ON CEC FOR REMOTES # you've to plug the ODROID XU4 on the HDMI1 of your tv # this is a limitation of the EXYNOS libcec adapter # ------------ A - System Options ----------- # # Uncomment the system.power.switch you use ;system.power.switch=ATX_RASPI_R2_6 # http://lowpowerlab.com/atxraspi/#installation ;system.power.switch=MAUSBERRY # http://mausberry-circuits.myshopify.com/pages/setup ;system.power.switch=REMOTEPIBOARD_2003 # http://www.msldigital.com/pages/support-for-remotepi-board-2013 ;system.power.switch=REMOTEPIBOARD_2005 # http://www.msldigital.com/pages/support-for-remotepi-board-plus-2015 ;system.power.switch=WITTYPI # http://www.uugear.com/witty-pi-realtime-clock-power-management-for-raspberry-pi ;system.power.switch=PIN56ONOFF # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN) ;system.power.switch=PIN56PUSH # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN) ;system.power.switch=PIN356ONOFFRESET # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN) ## Splash screen duration ## 0 : Video will be stopped when emulationstation is ready to start. ## -1 : All the video will be played before emulationstation start (default) ## >0 : Time the video will be played before emulationstation start (in seconds) system.splash.length=-1 ## Splash videos selection ## all: select a boot video in recalbox videos and user videos ## recalbox: select a boot video only in recalbox videos ## custom: select a boot video only in user videos ## Any invalid value means "all" system.splash.select=all ## Recalbox Manager (http manager) system.manager.enabled=1 ## Currently, only version 2 is available system.manager.version=2 ## Recalbox security # enforce security # samba password required # disable virtual gamepads system.security.enabled=0 ## Recalbox API (REST) system.api.enabled=0 ## EmulationStation ### menu style ### default -> default all options menu ### none -> no menu except the game search menu ### bartop -> less menu, only needed for bartops emulationstation.menu=default ### Select a system to show on boot (use rom directory name) (string) emulationstation.selectedsystem=favorites ### Show the gamelist of the first or selected system on boot (0,1) emulationstation.bootongamelist=0 ### Disable system view. ES will boot and show ONLY the first or selected system (0,1) emulationstation.hidesystemview=0 ### Pa**e Gamelists only. Show only games listed in gamelist.xml files (0,1) emulationstation.gamelistonly=0 ### Force basicgameList view to be displayed, even if your game systems are scraped (0,1) emulationstation.forcebasicgamelistview=0 ### Filter out adult games ### you may use emulationstation.snes.filteradultgames=1 ### to filter out adult games for the snes system or any other system ;emulationstation.filteradultgames=1 ### Zipped gamelist preference ### Whatever you choose, emulationstation can read both compressed ### and uncompressed gamelist.xml or gamelist.zip ### However updated gamelist will be saved in your prefered format. ### Zipped format may save load time, especially on slow devices. ### 0 = gamelist.xml ### 1 = gamelist.zip ;emulationstation.zippedgamelist=1 ## Arcade metasystem ## Activate the Arcade metasystem to group all games from piFBA, FBN (libretro), MAME and optionally Neogeo ## into a single "Arcade" system. ;emulationstation.arcade=1 ## You may want to specify its position in the system list. (Default: 0) ## Negatives values may be used to tart from the end (-1 = last position) ;emulationstation.arcade.position=0 ## Include NeoGeo or not (default: 1) ;emulationstation.arcade.includeneogeo=1 ## Hide included system or leave them in the system list (default: 1) ;emulationstation.arcade.hideoriginals=1 ## Virtual systems ### Activate a virtual system with all games available from all systems ;emulationstation.collection.allgames=1 ### Activate a virtual system with all multiplayer games (players >= 2) ;emulationstation.collection.multiplayers=1 ### Activate a virtual system with last played games ;emulationstation.collection.lastplayed=1 ## Videosnaps ### Delay before videosnaps start, in millisecond. Default: 2s ;emulationstation.videosnaps.delay=2000 ### Video loop times. 0 = no video. 1 or more = the video loops x times before fading out ;emulationstation.videosnaps.loop=1 ### Enable videosnap sound/music ;emulationstation.videosnaps.sound=1 ## Scrapers ### Activate this option to extract region from filename when possible ;scraper.extractregionfromfilename=1 ### Select the source of game's names ### 0 = from scrapper result (default) ### 1 = from filename ### 2 = from filename undecorated (i.e: (text) and [text] removed) ;scraper.getnamefrom=0 ### ScreenScraper.fr ### Force media region - if not defined, region is taken from system.language. Default: us ;scraper.screenscraper.region=eu ### Force text language - if not defined, region is taken from system.language. Default: en ;scraper.screenscraper.language=fr ### Choose the media to download among: ### screenshot: game screenshot ### title : game title screenshot ### box2d : Front case ### box3d : 3D rendered case ### mixv1 : Recalbox special mix image V1 (default) ### mixv2 : Recalbox special mix image V2 ;scraper.screenscraper.media=mixv1 ### ScreenScraper account ;scraper.screenscraper.user= ;scraper.screenscraper.password= ## Emulator special keys ## default -> default all special keys ## nomenu -> cannot popup the emulator menu ## none -> no special keys in emulators system.emulators.specialkeys=default ## Show or hide kodi in emulationstation (0,1) kodi.enabled=0 ## Start kodi at launch (0,1) kodi.atstartup=0 ## set x button shortcut (0,1) kodi.xbutton=0 ## Kodi can wait for a network component before starting ## waithost is the ip or hostname that must answer to a ping to validate the availability ## waittime is the maximum time waited when kodi boots ## if waitmode is required, kodi will not start if the component is not available ## if waitmode is wish, kodi will start if the component is not available ## if waitmode is not set or has another value, kodi will start immediately ;kodi.network.waitmode=required ;kodi.network.waittime=10 ;kodi.network.waithost=192.168.0.50 # ------------ B - Network ------------ # ## Set system hostname system.hostname=RECALBOX ## Activate wifi (0,1) wifi.enabled=0 ## Set wifi region ## More info here: https://github.com/recalbox/recalbox-os/wiki/Wifi-country-code-(EN) wifi.region=JP ## Wifi SSID (string) ;wifi.ssid=new ssid ## Wifi KEY (string) ## after rebooting the recalbox, the "new key" is replace by a hidden value "enc:xxxxx" ## you can edit the "enc:xxxxx" value to replace by a clear value, it will be updated again at the following reboot ## Escape your special chars (# ; $) with a backslash : $ => \$ ;wifi.key=new key ## Wifi - static IP ## if you want a static IP address, you must set all 3 values (ip, gateway, and netmask) ## if any value is missing or all lines are commented out, it will fall back to the ## default of DHCP ;wifi.ip=manual ip address ;wifi.gateway=new gateway ;wifi.netmask=new netmask # secondary wifi (not configurable via the user interface) ;wifi2.ssid=new ssid ;wifi2.key=new key # third wifi (not configurable via the user interface) ;wifi3.ssid=new ssid ;wifi3.key=new key ## Samba share system.samba.enabled=1 ### Virtual Gamepads system.virtual-gamepads.enabled=1 ### SSH system.ssh.enabled=1 # ------------ C - Audio ------------ # ## Set the audio device (auto, hdmi, jack) audio.device=alsa_card.0:hdmi-output-0 ## Set system volume (0..100) audio.volume=90 ## Enable or disable system sounds in ES (0,1) audio.bgmusic=1 # -------------- D - Controllers ----------------- # # Enable support for standard bluetooth controllers controllers.bluetooth.enabled=1 # Enable ERTM controllers.bluetooth.ertm=1 ## Please enable only one of these # -------------- D1 - PS3 Controllers ------------ # ##Enable PS3 controllers support controllers.ps3.enabled=1 ## Choose a driver between bluez, official and shanwan ## bluez -> bluez 5 + kernel drivers, support official and shanwan sisaxis ## official -> sixad drivers, support official and gasia sisaxis ## shanwan -> shanwan drivers, support official and shanwan sisaxis controllers.ps3.driver=bluez # ------------ D2 - GPIO Controllers ------------ # ## GPIO Controllers ## enable controllers on GPIO with mk_arcarde_joystick_rpi (0,1) controllers.gpio.enabled=0 ## mk_gpio arguments, map=1 for one controller, map=1,2 for 2 (map=1,map=1,2) controllers.gpio.args=map=1,2 ## DB9 Controllers ## Enable DB9 drivers for atari, megadrive, amiga controllers (0,1) controllers.db9.enabled=0 ## db9 arguments controllers.db9.args=map=1 ## Gamecon controllers ## Enable gamecon controllers, for nes, snes, psx (0,1) controllers.gamecon.enabled=0 ## gamecon_args controllers.gamecon.args=map=1 ## XGaming's XArcade Tankstik and other compatible devices controllers.xarcade.enabled=1 # ------------ D3 - Joycon Controllers ------------ # controllers.joycond.enabled=1 # ------------ E - Language and keyboard ------------ # ## Set the language of the system (fr_FR,en_US,en_GB,de_DE,pt_BR,es_ES,it_IT,eu_ES,tr_TR,zh_CN) system.language=fr_FR ## set the keyboard layout (fr,en,de,us,es) system.kblayout=fr ## Set you local time ## Select your timezone from : ls /usr/share/zoneinfo/ (string) ;system.timezone=Europe/Paris # ------------ F - UPDATES ------------ # ## Automatically check for updates at start (0,1) updates.enabled=1 # Update type : default to stable updates.type=stable # ------------ G - HERE IT IS - GLOBAL EMULATOR CONFIGURATION ------------ # ## The global value will be used for all emulators, except if the value ## is redefined in the emulator ## Set game resolution for emulators ## Please don't modify this setting ## This arch does not support the video mode switch ## (string) global.videomode=default ## Shader set ## Automatically select shaders for all systems ## (none, retro, scanlines) global.shaderset=none ## Once enabled, your screen will be cropped, and you will have a pixel perfect image (0,1) global.integerscale=0 ## Set gpslp shader for all emulators (prefer shadersets above). Absolute path (string) global.shaders= ## Set ratio for all emulators (auto,4/3,16/9,16/10,custom) global.ratio=auto ## Set smooth for all emulators (0,1) global.smooth=1 ## Set rewind for all emulators (0,1) global.rewind=1 ## Set autosave/load savestate for all emulators (0,1) global.autosave=0 ## Enable retroarchievements (0,1) ## Set your www.retroachievements.org username/password ## Escape your special chars (# ; $) with a backslash : $ => \$ global.retroachievements=0 global.retroachievements.hardcore=0 global.retroachievements.username= global.retroachievements.password= ## Set retroarch input driver (auto, udev, sdl2) ## If you don't have issues with your controllers, let auto global.inputdriver=auto ## If you do not want recalboxOS to generate the configuration for all emulators (string) ;global.configfile=/path/to/my/configfile.cfg ## Demo screensaver parameters ## Set the system list from which ES will run random games ## Empty list or unexisting key means all available systems global.demo.systemlist=3do,amigacd32,atari2600,atari5200,atari7800,daphne,fbneo,fds,gamegear,gba,lynx,mame,mastersystem,megadrive,neogeo,nes,ngpc,pcengine,sega32x,sg1000,snes ## Default demo game sessions last 90s. Change this value if you want shorter or longer sessions ;global.demo.duration=90 ## Default game info screen duration lasts 6s. Change this value if you want shorter or longer info screens. ;global.demo.infoscreenduration=6 ## Retroarch AI Translation service ## Comment out or set to 0 the following key if you don't want the AI service global.translate=1 ## Set the source and the target languages. ## Allowed language list: EN, ES, FR, IT, DE, JP, NL, CS, DA, SV, HR, KO, ZH_CN, ZH_TW, CA, BG, BN, EU, AZ, AR, SQ, ## AF, EO, ET, TL, FI, GL, KA, EL, GU, HT, IW, HI, HU, IS, ID, GA, KN, LA, LV, LT, MK, MS, ## MT, NO, FA, PL, PT, RO, RU, SR, SK, SL, SW, TA, TE, TH, TR, UK, UR, VI, CY, YI ## Setting the translate.from key to a specified language may speed up or give more accurate results ## If translate.to key is commented, the default value is extracted from system.language or, if system.language is ## undefined, set to auto (=EN). global.translate.from=auto global.translate.to=auto ## zTranslate API Key ## go to https://ztranslate.net and create an account. ## validate your account, then log in and go to the settngs page ## Look for the API Key at the bottom of the page, then uncomment the following key and paste your API Key: ;global.translate.apikey=RECALBOX ## Other translation service ## If you want to use another translation service or a custom API call, use this key to ## specify the url to call. If the key is not empty, it is used instead of zTranslation's API Key ;global.translate.url= # ------------ H - EMULATORS CHOICES ----------- # ## You can override the global configurations here ## Here is the snes example ;snes.core=snes9x2010 ;snes.shaders=/recalbox/share/shaders/shaders_glsl/mysnesshader.gplsp ;snes.ratio=16/9 ;snes.smooth=0 ;snes.rewind=1 ;snes.autosave=0 ;snes.emulator=libretro ;snes.integerscale=0 ## If you do not want recalboxOS to generate the configuration for the emulator: ;snes.configfile=/path/to/my/configfile.cfg ## Default cores for Odroid XU4 ;snes.core=snes9x n64.core=gliden64 ## NeoGeo emulator ## You can use pifba or a libretro core (fba2x,libretro) neogeo.emulator=libretro ## If you set libretro as neogeo.emulator, the line below sets the retroarch core (fbneo, mame2000) neogeo.core=fbneo ## Demo screensaver parameters ## Include or exclude a particular system from the demo screensaver ## You may change the global.demo.systemlist key or include/exclude every single system ;snes.demo.include=0 ## Set the session duration for a particular system ;snes.demo.duration=90 # ------------ J - TFT SECONDARY SCREEN ----------- # #Second miniTFT screen as marquee to display scrapes and videos #Enable it with system.secondMiniTFT.enabled=1, disable with system.secondMiniTFT.enabled=0 #this configuration is REQUIRED system.secondminitft.enabled=1 #Type of mini TFT : OGST, unknown #Most of spi tft screen are enabled thanks to overlays in /boot/config.txt in rpi and /boot/config.ini on odroidxu4 #please check the specific configuration of your screen #Some examples are available on the page ..... # values are : # - overlay : screen configured through overlays in /boot/config.txt or /boot/config.ini (odroidxu4/ogst) # - default : the rest of the world #this configuration is REQUIRED if system.secondminitft.enabled=1 system.secondminitft.type=overlay #Choose the resolution of your screen #miniTFT resolution 320x240 -> 240p, 480x320 -> 320p #this configuration is REQUIRED if system.secondminitft.enabled=1 system.secondminitft.resolution=240p #Scraped image aspect on tft screen : fbv display option # options available : stretch, ignore-aspect, enlarge. # stretch : Strech (using a simple resizing routine) the image to fit onto screen if necessary # alpha : use the alpha channel (if applicable) # ignore-aspect : Ignore the image aspect while resizing # enlarge : Enlarge the image to fit the whole screen if necessary # 1 = enabled, 0 = disabled #this configuration is REQUIRED if system.secondminitft.enabled=1 system.secondminitft.imagestretchenabled=1 system.secondminitft.imageenlargeenabled=0 system.secondminitft.imagealphaenabled=1 system.secondminitft.imageignoreaspectenabled=1 #When activating the second TFT screen, you may want to display #game scraped video only on the second screen. This variable #allows you to disable scraped video playing in ES during game browsing #system.secondminitft.disablevideoines=1 disable video playing in ES #system.secondminitft.disablevideoines=0 enable video playing in ES #this configuration is OPTIONAL if system.secondminitft.enabled=1 system.secondminitft.disablevideoines=1 #if the backlight of your your screen can be manage by PWM, #indicates the GPIO value of your PWM control #WiringPi and its gpio program will be used to control the backlight #when RB goes in SLEEP mode, and when it wakes up. #On raspberry pi, PWMs cannot be used simultaneously with Jack sound output. #If your are using HDMI or a Audio hat you can use backlight PWM control for the second screen #If you are using Jack output please leave commented. #The Screen will be switch down in Sleep mode, and switch on when it wakes up. #On OGST, only this mode is available. #this configuration is OPTIONAL if system.secondminitft.enabled=1 ;system.secondminitft.backlightcontrol=18 # system.secondminitft.usemarquee variabla allows you to display a different # image during running game. just creat a directory named "marquees" in media # aside videos and images and put new images with the same name as in images # example : # - /recalbox/share/roms/neogeo/media/marquees/alpham2.png # - /recalbox/share/roms/neogeo/media/images/alpham2.png # if set to 1, in game the marquee images will be displayed # if set to 0, in game the scraped images will be displayed ;system.secondminitft.usemarquee=0 #system.secondminitft.sleepenabled allows you to enable/disable #sleep mode for the second TFT. If set to 1 sleep mode is enabled and #backlight of the screen will be OFF. If set to 0, sleep mode is #disabled and the backlight of the screen will be always On ;system.secondminitft.sleepenabled=0 # ------------ I - NETPLAY PARAMETERS ----------- # ## All these values are handled by Recalbox itself global.netplay=1 global.netplay.nickname= global.netplay.port=55435 global.netplay.relay= global.netplay.systems=fbneo,mame,mastersystem,megadrive,neogeo,nes,pcengine,sega32x,sg1000,snes,supergrafx,atari2600,pcenginecd,pcfx,fds,tic80,segacd,mrboom,colecovision global.netplay.lobby=http://lobby.libretro.com/list/ ## Configurations generated by Recalbox emulationstation.theme.recalbox-next.colorset=1-light blue colors emulationstation.theme.recalbox-next.gameclipview=0 - DEFAULT emulationstation.theme.recalbox-next.gamelistview=1-standard gamelist emulationstation.theme.recalbox-next.region=us emulationstation.theme.recalbox-next.iconset=1-standard icons emulationstation.theme.recalbox-next.menuset=1-light blue icons emulationstation.theme.recalbox-next.systemview=1-vertical left system.firsttimeuse=0 emulationstation.pad1=030000005e0400008e02000020010000:Xbox 360 Controller emulationstation.pad0=030000005e0400008e02000014010000:Xbox 360 Controllerconfig.ini
[generic] ; Device Tree Overlay overlay_resize=16384 ; uncomment next line to enable Odroid XU4 OGST overlay_profile=hktft_cs_ogst overlays="spi0 i2c0 i2c1 uart0" [overlay_hktft_cs_ogst] overlays="hktft-cs-ogst i2c0"j'ai fait une réinstallé de nouveau le fichier recalbox.conf par défaut la ligne 388 est sur 0 avec ; devant , pour la ligne 398 idem ; , pareil ligne 404 , ligne 416 à la ligne 419 ; devant toute et sur la 418 j'ai 0 à la place de 1 ,ligne 428 ; au début .
sur le config.ini la ligne 5 j'ai ; au début
J'ai mis à l'identique aucun changement -
voila mon fichier recalbox.conf
# System Variable # You can configure your recalbox from here # To set a variable, remove the first ; on the line # NOTE ON CEC FOR REMOTES # you've to plug the ODROID XU4 on the HDMI1 of your tv # this is a limitation of the EXYNOS libcec adapter # ------------ A - System Options ----------- # # Uncomment the system.power.switch you use ;system.power.switch=ATX_RASPI_R2_6 # http://lowpowerlab.com/atxraspi/#installation ;system.power.switch=MAUSBERRY # http://mausberry-circuits.myshopify.com/pages/setup ;system.power.switch=REMOTEPIBOARD_2003 # http://www.msldigital.com/pages/support-for-remotepi-board-2013 ;system.power.switch=REMOTEPIBOARD_2005 # http://www.msldigital.com/pages/support-for-remotepi-board-plus-2015 ;system.power.switch=WITTYPI # http://www.uugear.com/witty-pi-realtime-clock-power-management-for-raspberry-pi ;system.power.switch=PIN56ONOFF # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN) ;system.power.switch=PIN56PUSH # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN) ;system.power.switch=PIN356ONOFFRESET # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN) ## Splash screen duration ## 0 : Video will be stopped when emulationstation is ready to start. ## -1 : All the video will be played before emulationstation start (default) ## >0 : Time the video will be played before emulationstation start (in seconds) system.splash.length=-1 ## Splash videos selection ## all: select a boot video in recalbox videos and user videos ## recalbox: select a boot video only in recalbox videos ## custom: select a boot video only in user videos ## Any invalid value means "all" system.splash.select=all ## Recalbox Manager (http manager) system.manager.enabled=1 ## Currently, only version 2 is available system.manager.version=2 ## Recalbox security # enforce security # samba password required # disable virtual gamepads system.security.enabled=0 ## Recalbox API (REST) system.api.enabled=0 ## EmulationStation ### menu style ### default -> default all options menu ### none -> no menu except the game search menu ### bartop -> less menu, only needed for bartops emulationstation.menu=default ### Select a system to show on boot (use rom directory name) (string) emulationstation.selectedsystem=favorites ### Show the gamelist of the first or selected system on boot (0,1) emulationstation.bootongamelist=0 ### Disable system view. ES will boot and show ONLY the first or selected system (0,1) emulationstation.hidesystemview=0 ### Pa**e Gamelists only. Show only games listed in gamelist.xml files (0,1) emulationstation.gamelistonly=0 ### Force basicgameList view to be displayed, even if your game systems are scraped (0,1) emulationstation.forcebasicgamelistview=0 ### Filter out adult games ### you may use emulationstation.snes.filteradultgames=1 ### to filter out adult games for the snes system or any other system emulationstation.filteradultgames=0 ### Zipped gamelist preference ### Whatever you choose, emulationstation can read both compressed ### and uncompressed gamelist.xml or gamelist.zip ### However updated gamelist will be saved in your prefered format. ### Zipped format may save load time, especially on slow devices. ### 0 = gamelist.xml ### 1 = gamelist.zip ;emulationstation.zippedgamelist=1 ## Arcade metasystem ## Activate the Arcade metasystem to group all games from piFBA, FBN (libretro), MAME and optionally Neogeo ## into a single "Arcade" system. ;emulationstation.arcade=1 ## You may want to specify its position in the system list. (Default: 0) ## Negatives values may be used to tart from the end (-1 = last position) ;emulationstation.arcade.position=0 ## Include NeoGeo or not (default: 1) ;emulationstation.arcade.includeneogeo=1 ## Hide included system or leave them in the system list (default: 1) ;emulationstation.arcade.hideoriginals=1 ## Virtual systems ### Activate a virtual system with all games available from all systems ;emulationstation.collection.allgames=1 ### Activate a virtual system with all multiplayer games (players >= 2) ;emulationstation.collection.multiplayers=1 ### Activate a virtual system with last played games ;emulationstation.collection.lastplayed=1 ## Videosnaps ### Delay before videosnaps start, in millisecond. Default: 2s ;emulationstation.videosnaps.delay=2000 ### Video loop times. 0 = no video. 1 or more = the video loops x times before fading out ;emulationstation.videosnaps.loop=1 ### Enable videosnap sound/music ;emulationstation.videosnaps.sound=1 ## Scrapers ### Activate this option to extract region from filename when possible ;scraper.extractregionfromfilename=1 ### Select the source of game's names ### 0 = from scrapper result (default) ### 1 = from filename ### 2 = from filename undecorated (i.e: (text) and [text] removed) ;scraper.getnamefrom=0 ### ScreenScraper.fr ### Force media region - if not defined, region is taken from system.language. Default: us ;scraper.screenscraper.region=eu ### Force text language - if not defined, region is taken from system.language. Default: en ;scraper.screenscraper.language=fr ### Choose the media to download among: ### screenshot: game screenshot ### title : game title screenshot ### box2d : Front case ### box3d : 3D rendered case ### mixv1 : Recalbox special mix image V1 (default) ### mixv2 : Recalbox special mix image V2 ;scraper.screenscraper.media=mixv1 ### ScreenScraper account ;scraper.screenscraper.user= ;scraper.screenscraper.password= ## Emulator special keys ## default -> default all special keys ## nomenu -> cannot popup the emulator menu ## none -> no special keys in emulators system.emulators.specialkeys=default ## Show or hide kodi in emulationstation (0,1) kodi.enabled=0 ## Start kodi at launch (0,1) kodi.atstartup=0 ## set x button shortcut (0,1) kodi.xbutton=0 ## Kodi can wait for a network component before starting ## waithost is the ip or hostname that must answer to a ping to validate the availability ## waittime is the maximum time waited when kodi boots ## if waitmode is required, kodi will not start if the component is not available ## if waitmode is wish, kodi will start if the component is not available ## if waitmode is not set or has another value, kodi will start immediately ;kodi.network.waitmode=required ;kodi.network.waittime=10 ;kodi.network.waithost=192.168.0.50 # ------------ B - Network ------------ # ## Set system hostname system.hostname=RECALBOX ## Activate wifi (0,1) wifi.enabled=0 ## Set wifi region ## More info here: https://github.com/recalbox/recalbox-os/wiki/Wifi-country-code-(EN) wifi.region=JP ## Wifi SSID (string) ;wifi.ssid=new ssid ## Wifi KEY (string) ## after rebooting the recalbox, the "new key" is replace by a hidden value "enc:xxxxx" ## you can edit the "enc:xxxxx" value to replace by a clear value, it will be updated again at the following reboot ## Escape your special chars (# ; $) with a backslash : $ => \$ ;wifi.key=new key ## Wifi - static IP ## if you want a static IP address, you must set all 3 values (ip, gateway, and netmask) ## if any value is missing or all lines are commented out, it will fall back to the ## default of DHCP ;wifi.ip=manual ip address ;wifi.gateway=new gateway ;wifi.netmask=new netmask # secondary wifi (not configurable via the user interface) ;wifi2.ssid=new ssid ;wifi2.key=new key # third wifi (not configurable via the user interface) ;wifi3.ssid=new ssid ;wifi3.key=new key ## Samba share system.samba.enabled=1 ### Virtual Gamepads system.virtual-gamepads.enabled=1 ### SSH system.ssh.enabled=1 # ------------ C - Audio ------------ # ## Set the audio device (auto, hdmi, jack) audio.device=alsa_card.0:hdmi-output-0 ## Set system volume (0..100) audio.volume=90 ## Enable or disable system sounds in ES (0,1) audio.bgmusic=1 # -------------- D - Controllers ----------------- # # Enable support for standard bluetooth controllers controllers.bluetooth.enabled=1 # Enable ERTM controllers.bluetooth.ertm=1 ## Please enable only one of these # -------------- D1 - PS3 Controllers ------------ # ##Enable PS3 controllers support controllers.ps3.enabled=1 ## Choose a driver between bluez, official and shanwan ## bluez -> bluez 5 + kernel drivers, support official and shanwan sisaxis ## official -> sixad drivers, support official and gasia sisaxis ## shanwan -> shanwan drivers, support official and shanwan sisaxis controllers.ps3.driver=bluez # ------------ D2 - GPIO Controllers ------------ # ## GPIO Controllers ## enable controllers on GPIO with mk_arcarde_joystick_rpi (0,1) controllers.gpio.enabled=0 ## mk_gpio arguments, map=1 for one controller, map=1,2 for 2 (map=1,map=1,2) controllers.gpio.args=map=1,2 ## DB9 Controllers ## Enable DB9 drivers for atari, megadrive, amiga controllers (0,1) controllers.db9.enabled=0 ## db9 arguments controllers.db9.args=map=1 ## Gamecon controllers ## Enable gamecon controllers, for nes, snes, psx (0,1) controllers.gamecon.enabled=0 ## gamecon_args controllers.gamecon.args=map=1 ## XGaming's XArcade Tankstik and other compatible devices controllers.xarcade.enabled=1 # ------------ D3 - Joycon Controllers ------------ # controllers.joycond.enabled=1 # ------------ E - Language and keyboard ------------ # ## Set the language of the system (fr_FR,en_US,en_GB,de_DE,pt_BR,es_ES,it_IT,eu_ES,tr_TR,zh_CN) system.language=fr_FR ## set the keyboard layout (fr,en,de,us,es) system.kblayout=fr ## Set you local time ## Select your timezone from : ls /usr/share/zoneinfo/ (string) ;system.timezone=Europe/Paris # ------------ F - UPDATES ------------ # ## Automatically check for updates at start (0,1) updates.enabled=1 # Update type : default to stable updates.type=stable # ------------ G - HERE IT IS - GLOBAL EMULATOR CONFIGURATION ------------ # ## The global value will be used for all emulators, except if the value ## is redefined in the emulator ## Set game resolution for emulators ## Please don't modify this setting ## This arch does not support the video mode switch ## (string) global.videomode=default ## Shader set ## Automatically select shaders for all systems ## (none, retro, scanlines) global.shaderset=none ## Once enabled, your screen will be cropped, and you will have a pixel perfect image (0,1) global.integerscale=0 ## Set gpslp shader for all emulators (prefer shadersets above). Absolute path (string) global.shaders= ## Set ratio for all emulators (auto,4/3,16/9,16/10,custom) global.ratio=auto ## Set smooth for all emulators (0,1) global.smooth=1 ## Set rewind for all emulators (0,1) global.rewind=1 ## Set autosave/load savestate for all emulators (0,1) global.autosave=0 ## Enable retroarchievements (0,1) ## Set your www.retroachievements.org username/password ## Escape your special chars (# ; $) with a backslash : $ => \$ global.retroachievements=0 global.retroachievements.hardcore=0 global.retroachievements.username= global.retroachievements.password= ## Set retroarch input driver (auto, udev, sdl2) ## If you don't have issues with your controllers, let auto global.inputdriver=auto ## If you do not want recalboxOS to generate the configuration for all emulators (string) ;global.configfile=/path/to/my/configfile.cfg ## Demo screensaver parameters ## Set the system list from which ES will run random games ## Empty list or unexisting key means all available systems global.demo.systemlist=3do,amigacd32,atari2600,atari5200,atari7800,daphne,fbneo,fds,gamegear,gba,lynx,mame,mastersystem,megadrive,neogeo,nes,ngpc,pcengine,sega32x,sg1000,snes ## Default demo game sessions last 90s. Change this value if you want shorter or longer sessions ;global.demo.duration=90 ## Default game info screen duration lasts 6s. Change this value if you want shorter or longer info screens. ;global.demo.infoscreenduration=6 ## Retroarch AI Translation service ## Comment out or set to 0 the following key if you don't want the AI service global.translate=1 ## Set the source and the target languages. ## Allowed language list: EN, ES, FR, IT, DE, JP, NL, CS, DA, SV, HR, KO, ZH_CN, ZH_TW, CA, BG, BN, EU, AZ, AR, SQ, ## AF, EO, ET, TL, FI, GL, KA, EL, GU, HT, IW, HI, HU, IS, ID, GA, KN, LA, LV, LT, MK, MS, ## MT, NO, FA, PL, PT, RO, RU, SR, SK, SL, SW, TA, TE, TH, TR, UK, UR, VI, CY, YI ## Setting the translate.from key to a specified language may speed up or give more accurate results ## If translate.to key is commented, the default value is extracted from system.language or, if system.language is ## undefined, set to auto (=EN). global.translate.from=auto global.translate.to=auto ## zTranslate API Key ## go to https://ztranslate.net and create an account. ## validate your account, then log in and go to the settngs page ## Look for the API Key at the bottom of the page, then uncomment the following key and paste your API Key: ;global.translate.apikey=RECALBOX ## Other translation service ## If you want to use another translation service or a custom API call, use this key to ## specify the url to call. If the key is not empty, it is used instead of zTranslation's API Key ;global.translate.url= # ------------ H - EMULATORS CHOICES ----------- # ## You can override the global configurations here ## Here is the snes example ;snes.core=snes9x2010 ;snes.shaders=/recalbox/share/shaders/shaders_glsl/mysnesshader.gplsp ;snes.ratio=16/9 ;snes.smooth=0 ;snes.rewind=1 ;snes.autosave=0 ;snes.emulator=libretro ;snes.integerscale=0 ## If you do not want recalboxOS to generate the configuration for the emulator: ;snes.configfile=/path/to/my/configfile.cfg ## Default cores for Odroid XU4 ;snes.core=snes9x n64.core=gliden64 ## NeoGeo emulator ## You can use pifba or a libretro core (fba2x,libretro) neogeo.emulator=libretro ## If you set libretro as neogeo.emulator, the line below sets the retroarch core (fbneo, mame2000) neogeo.core=fbneo ## Demo screensaver parameters ## Include or exclude a particular system from the demo screensaver ## You may change the global.demo.systemlist key or include/exclude every single system ;snes.demo.include=0 ## Set the session duration for a particular system ;snes.demo.duration=90 # ------------ J - TFT SECONDARY SCREEN ----------- # #Second miniTFT screen as marquee to display scrapes and videos #Enable it with system.secondMiniTFT.enabled=1, disable with system.secondMiniTFT.enabled=0 #this configuration is REQUIRED system.secondminitft.enabled=0 #Type of mini TFT : OGST, unknown #Most of spi tft screen are enabled thanks to overlays in /boot/config.txt in rpi and /boot/config.ini on odroidxu4 #please check the specific configuration of your screen #Some examples are available on the page ..... # values are : # - overlay : screen configured through overlays in /boot/config.txt or /boot/config.ini (odroidxu4/ogst) # - default : the rest of the world #this configuration is REQUIRED if system.secondminitft.enabled=1 ;system.secondminitft.type=overlay #Choose the resolution of your screen #miniTFT resolution 320x240 -> 240p, 480x320 -> 320p #this configuration is REQUIRED if system.secondminitft.enabled=1 ;system.secondminitft.resolution=240p #Scraped image aspect on tft screen : fbv display option # options available : stretch, ignore-aspect, enlarge. # stretch : Strech (using a simple resizing routine) the image to fit onto screen if necessary # alpha : use the alpha channel (if applicable) # ignore-aspect : Ignore the image aspect while resizing # enlarge : Enlarge the image to fit the whole screen if necessary # 1 = enabled, 0 = disabled #this configuration is REQUIRED if system.secondminitft.enabled=1 ;system.secondminitft.imagestretchenabled=1 ;system.secondminitft.imageenlargeenabled=0 ;system.secondminitft.imagealphaenabled=0 ;system.secondminitft.imageignoreaspectenabled=1 #When activating the second TFT screen, you may want to display #game scraped video only on the second screen. This variable #allows you to disable scraped video playing in ES during game browsing #system.secondminitft.disablevideoines=1 disable video playing in ES #system.secondminitft.disablevideoines=0 enable video playing in ES #this configuration is OPTIONAL if system.secondminitft.enabled=1 ;system.secondminitft.disablevideoines=1 #if the backlight of your your screen can be manage by PWM, #indicates the GPIO value of your PWM control #WiringPi and its gpio program will be used to control the backlight #when RB goes in SLEEP mode, and when it wakes up. #On raspberry pi, PWMs cannot be used simultaneously with Jack sound output. #If your are using HDMI or a Audio hat you can use backlight PWM control for the second screen #If you are using Jack output please leave commented. #The Screen will be switch down in Sleep mode, and switch on when it wakes up. #On OGST, only this mode is available. #this configuration is OPTIONAL if system.secondminitft.enabled=1 ;system.secondminitft.backlightcontrol=18 # system.secondminitft.usemarquee variabla allows you to display a different # image during running game. just creat a directory named "marquees" in media # aside videos and images and put new images with the same name as in images # example : # - /recalbox/share/roms/neogeo/media/marquees/alpham2.png # - /recalbox/share/roms/neogeo/media/images/alpham2.png # if set to 1, in game the marquee images will be displayed # if set to 0, in game the scraped images will be displayed ;system.secondminitft.usemarquee=0 #system.secondminitft.sleepenabled allows you to enable/disable #sleep mode for the second TFT. If set to 1 sleep mode is enabled and #backlight of the screen will be OFF. If set to 0, sleep mode is #disabled and the backlight of the screen will be always On ;system.secondminitft.sleepenabled=0 # ------------ I - NETPLAY PARAMETERS ----------- # ## All these values are handled by Recalbox itself global.netplay=1 global.netplay.nickname= global.netplay.port=55435 global.netplay.relay= global.netplay.systems=fbneo,mame,mastersystem,megadrive,neogeo,nes,pcengine,sega32x,sg1000,snes,supergrafx,atari2600,pcenginecd,pcfx,fds,tic80,segacd,mrboom,colecovision global.netplay.lobby=http://lobby.libretro.com/list/ ## Configurations generated by Recalbox emulationstation.theme.recalbox-next.colorset=1-light blue colors emulationstation.theme.recalbox-next.gameclipview=0 - DEFAULT emulationstation.theme.recalbox-next.gamelistview=1-standard gamelist emulationstation.theme.recalbox-next.region=us emulationstation.theme.recalbox-next.iconset=1-standard icons emulationstation.theme.recalbox-next.menuset=1-light blue icons emulationstation.theme.recalbox-next.systemview=1-vertical left system.firsttimeuse=0 emulationstation.pad0=030000005e0400008e02000014010000:Xbox 360 Controller emulationstation.clock=1mon fichier config.ini
[generic] ; Device Tree Overlay overlay_resize=16384 ; uncomment next line to enable Odroid XU4 OGST overlay_profile=hktft_cs_ogst overlays="spi0 i2c0 i2c1 uart0" [overlay_hktft_cs_ogst] overlays="hktft-cs-ogst i2c0" -
@davidb2111 Merci de ces précisions. Ca redonne un peu d'espoir.
-
@cedric-debuiselle Je ne comprends pas bien, ces fichiers ne sont du tout comme la solution donnée.
-
@loli72 said in Retour 7.2.2 sur XU4:
@cedric-debuiselle Je ne comprends pas bien, ces fichiers ne sont du tout comme la solution donnée.
j'ai indiqué les fichier que j'ai après la mise en route de recalbox
la je vais essayer d'installer retropie ou emulationstation, car je voudrais juste allumer l'écran pour voir si il n'est pas défectueux
si il y avait une commande pour mettre le rétro-éclairage ou juste une image ça serais pratique -
Je suis tombé sur une de mes vieilles sd card avec la 6.1.1, matériel fonctionne de mon côté problème de l'OS
-
@cedric-debuiselle
Normalement, si l'OGST est détecté, tu devrais avoir un fichier système/dev/fb1
Tu peux lui envoyer des données brutes avec la commandedd, je pense. -
@davidb2111 Bonne nouvelle !
Merci d'avoir pris le temps d'analyser le problème et de nous avoir donné ces informations.
Bon courage à toute l'équipe
Odroid XU4Q + Boitier OGST
-
@davidb2111 said in Retour 7.2.2 sur XU4:
@cedric-debuiselle
Normalement, si l'OGST est détecté, tu devrais avoir un fichier système/dev/fb1
Tu peux lui envoyer des données brutes avec la commandedd, je pense.j'ai l'impression qu'on a un soucis de détection de l'écran, normalement je devrais d'après se que tu me dit un fichier fb1, dans l'emplacement fichier racine dev/, j'en ai aucun
-
Pourrais-tu m'envoyer la sortie de la commande
dmesg | grep fbstp ? -
@davidb2111
/boot$ dmesg | grep fb
[ 3.336086] exynos-drm exynos-drm: fb0: exynosdrmfb frame buffer devicedit moi je voudrais mettre une signature comme toi sur mon profil j'arrive pas à trouver où sais
-
@cedric-debuiselle said in Retour 7.2.2 sur XU4:
dit moi je voudrais mettre une signature comme toi sur mon profil j'arrive pas à trouver où sais
ta réputation est de 0 donc tu ne peux pas
-
-
@davidb2111 Merci pour ces retours, ça fait plaisir !
-
@cedric-debuiselle tu as réussi à ressoude ton problème ?
moi de mon coté je viens d'essayer de faire une nouvelle installe sur une nouvelle carte SD et sans surprise toujours rien .... -
@cedric-debuiselle said in Retour 7.2.2 sur XU4:
@davidb2111
/boot$ dmesg | grep fb
[ 3.336086] exynos-drm exynos-drm: fb0: exynosdrmfb frame buffer devicedit moi je voudrais mettre une signature comme toi sur mon profil j'arrive pas à trouver où sais
Arg, le module tft n'est pas chargé. Tu pourrais m'envoyer le résultat de la commande
dmesg, ton fichier/boot/boot.iniet ton fichier/boot/config.ini, stp ?
