@davidb2111 Merci de ces précisions. Ca redonne un peu d'espoir. 
@cedric-debuiselle Je ne comprends pas bien, ces fichiers ne sont du tout comme la solution donnée.
@loli72 said in Retour 7.2.2 sur XU4:
@cedric-debuiselle Je ne comprends pas bien, ces fichiers ne sont du tout comme la solution donnée.
j'ai indiqué les fichier que j'ai après la mise en route de recalbox
la je vais essayer d'installer retropie ou emulationstation, car je voudrais juste allumer l'écran pour voir si il n'est pas défectueux
si il y avait une commande pour mettre le rétro-éclairage ou juste une image ça serais pratique
Je suis tombé sur une de mes vieilles sd card avec la 6.1.1, matériel fonctionne de mon côté problème de l'OS
@cedric-debuiselle
Normalement, si l'OGST est détecté, tu devrais avoir un fichier système /dev/fb1
Tu peux lui envoyer des données brutes avec la commande dd, je pense.
@davidb2111 Bonne nouvelle !
Merci d'avoir pris le temps d'analyser le problème et de nous avoir donné ces informations.
Bon courage à toute l'équipe 
Odroid XU4Q + Boitier OGST
@davidb2111 said in Retour 7.2.2 sur XU4:
@cedric-debuiselle
Normalement, si l'OGST est détecté, tu devrais avoir un fichier système/dev/fb1
Tu peux lui envoyer des données brutes avec la commandedd, je pense.
j'ai l'impression qu'on a un soucis de détection de l'écran, normalement je devrais d'après se que tu me dit un fichier fb1, dans l'emplacement fichier racine dev/, j'en ai aucun
Pourrais-tu m'envoyer la sortie de la commande dmesg | grep fb stp ?
@davidb2111
/boot$ dmesg | grep fb
[ 3.336086] exynos-drm exynos-drm: fb0: exynosdrmfb frame buffer device
dit moi je voudrais mettre une signature comme toi sur mon profil j'arrive pas à trouver où sais
@cedric-debuiselle said in Retour 7.2.2 sur XU4:
dit moi je voudrais mettre une signature comme toi sur mon profil j'arrive pas à trouver où sais
ta réputation est de 0 donc tu ne peux pas
@davidb2111 Merci pour ces retours, ça fait plaisir !
@cedric-debuiselle tu as réussi à ressoude ton problème ?
moi de mon coté je viens d'essayer de faire une nouvelle installe sur une nouvelle carte SD et sans surprise toujours rien ....
@cedric-debuiselle said in Retour 7.2.2 sur XU4:
@davidb2111
/boot$ dmesg | grep fb
[ 3.336086] exynos-drm exynos-drm: fb0: exynosdrmfb frame buffer devicedit moi je voudrais mettre une signature comme toi sur mon profil j'arrive pas à trouver où sais
Arg, le module tft n'est pas chargé. Tu pourrais m'envoyer le résultat de la commande dmesg, ton fichier /boot/boot.ini et ton fichier /boot/config.ini, stp ?
@davidb2111 said in Retour 7.2.2 sur XU4:
@cedric-debuiselle said in Retour 7.2.2 sur XU4:
@davidb2111
/boot$ dmesg | grep fb
[ 3.336086] exynos-drm exynos-drm: fb0: exynosdrmfb frame buffer devicedit moi je voudrais mettre une signature comme toi sur mon profil j'arrive pas à trouver où sais
Arg, le module tft n'est pas chargé. Tu pourrais m'envoyer le résultat de la commande
dmesg, ton fichier/boot/boot.iniet ton fichier/boot/config.ini, stp ?
dsmeg
# dmesg
[ 0.000000] Booting Linux on physical CPU 0x100
[ 0.000000] Linux version 5.4.109 (root@208a151257ba) (gcc version 10.2.0 (Buildroot 2020.11-dirty)) #1 SMP PREEMPT Thu Jun 17 21:48:16 CEST 2021
[ 0.000000] CPU: ARMv7 Processor [410fc073] revision 3 (ARMv7), cr=10c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Hardkernel Odroid XU4
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] cma: Reserved 128 MiB at 0xb6800000
[ 0.000000] Samsung CPU ID: 0xe5422001
[ 0.000000] On node 0 totalpages: 518656
[ 0.000000] Normal zone: 1728 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 196608 pages, LIFO batch:63
[ 0.000000] HighMem zone: 322048 pages, LIFO batch:63
[ 0.000000] Running under secure firmware.
[ 0.000000] percpu: Embedded 20 pages/cpu s52428 r8192 d21300 u81920
[ 0.000000] pcpu-alloc: s52428 r8192 d21300 u81920 alloc=20*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [0] 6 [0] 7
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 516928
[ 0.000000] Kernel command line: label=RECALBOX console=ttySAC2,115200n8 consoleblank=0 vt.global_cursor_default=0 governor=performance video=HDMI-A-1:1920x1080@60 HPD=false vout=hdmi s5p_mfc.mem=16M
[ 0.000000] hdmi: using HDMI mode
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 1906832K/2074624K available (10240K kernel code, 781K rwdata, 2752K rodata, 1024K init, 322K bss, 36720K reserved, 131072K cma-reserved, 1157120K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] random: get_random_bytes called from start_kernel+0x330/0x50c with crng_init=0
[ 0.000000] Switching to timer-based delay loop, resolution 41ns
[ 0.000000] clocksource: mct-frc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.000007] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[ 0.000030] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 49
[ 0.001635] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 0.001654] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.001674] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.001687] Ignoring duplicate/late registration of read_current_timer delay
[ 0.002214] Console: colour dummy device 80x30
[ 0.002258] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[ 0.002274] pid_max: default: 32768 minimum: 301
[ 0.002473] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.002496] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.003590] CPU: Testing write buffer coherency: ok
[ 0.004169] CPU0: thread -1, cpu 0, socket 1, mpidr 80000100
[ 0.005049] Setting up static identity map for 0x40100000 - 0x40100060
[ 0.005339] ARM CCI driver probed
[ 0.005904] Exynos MCPM support installed
[ 0.006186] rcu: Hierarchical SRCU implementation.
[ 0.008630] soc soc0: Exynos: CPU[EXYNOS5800] PRO_ID[0xe5422001] REV[0x1] Detected
[ 0.009134] smp: Bringing up secondary CPUs ...
[ 0.010085] CPU1: thread -1, cpu 1, socket 1, mpidr 80000101
[ 0.011155] CPU2: thread -1, cpu 2, socket 1, mpidr 80000102
[ 0.012172] CPU3: thread -1, cpu 3, socket 1, mpidr 80000103
[ 0.013243] CPU4: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.013253] CPU4: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[ 0.014381] CPU5: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.014389] CPU5: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[ 0.015476] CPU6: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.015485] CPU6: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[ 0.016622] CPU7: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.016631] CPU7: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[ 0.016821] smp: Brought up 1 node, 8 CPUs
[ 0.016840] SMP: Total of 8 processors activated (384.00 BogoMIPS).
[ 0.016848] CPU: All CPU(s) started in HYP mode.
[ 0.016855] CPU: Virtualization extensions available.
[ 0.017948] devtmpfs: initialized
[ 0.037597] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[ 0.037977] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.037999] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
[ 0.040305] pinctrl core: initialized pinctrl subsystem
[ 0.042631] NET: Registered protocol family 16
[ 0.045724] DMA: preallocated 2048 KiB pool for atomic coherent allocations
[ 0.047171] audit: initializing netlink subsys (disabled)
[ 0.047379] audit: type=2000 audit(0.044:1): state=initialized audit_enabled=0 res=1
[ 0.048109] cpuidle: using governor menu
[ 0.048480] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.048492] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.112665] EXYNOS5420 PMU initialized
[ 0.226521] iommu: Default domain type: Translated
[ 0.226946] usbcore: registered new interface driver usbfs
[ 0.227001] usbcore: registered new interface driver hub
[ 0.227059] usbcore: registered new device driver usb
[ 0.227660] s3c-i2c 12c80000.i2c: slave address 0x00
[ 0.227678] s3c-i2c 12c80000.i2c: bus frequency set to 65 KHz
[ 0.227951] s3c-i2c 12c80000.i2c: i2c-2: S3C I2C adapter
[ 0.228461] mc: Linux media interface: v0.10
[ 0.228503] videodev: Linux video capture interface: v2.00
[ 0.228608] pps_core: LinuxPPS API ver. 1 registered
[ 0.228650] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.229029] Advanced Linux Sound Architecture Driver Initialized.
[ 0.229799] clocksource: Switched to clocksource mct-frc
[ 0.521818] random: fast init done
[ 0.955824] VFS: Disk quotas dquot_6.6.0
[ 0.955899] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.967235] thermal_sys: Registered thermal governor 'step_wise'
[ 0.969534] NET: Registered protocol family 2
[ 0.970295] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.970330] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.970410] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.970567] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.970674] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.970720] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.970940] NET: Registered protocol family 1
[ 0.971591] RPC: Registered named UNIX socket transport module.
[ 0.971603] RPC: Registered udp transport module.
[ 0.971613] RPC: Registered tcp transport module.
[ 0.971624] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.971842] Trying to unpack rootfs image as initramfs...
[ 0.980277] Freeing initrd memory: 1264K
[ 0.981689] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[ 0.982575] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
[ 0.986476] Initialise system trusted keyrings
[ 0.986706] workingset: timestamp_bits=14 max_order=19 bucket_order=5
[ 0.995778] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.996506] NFS: Registering the id_resolver key type
[ 0.996531] Key type id_resolver registered
[ 0.996542] Key type id_legacy registered
[ 0.996563] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.996581] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 0.996620] romfs: ROMFS MTD (C) 2007 Red Hat, Inc.
[ 1.026366] Key type asymmetric registered
[ 1.026380] Asymmetric key pa**er 'x509' registered
[ 1.026441] bounce: pool size: 64 pages
[ 1.026483] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
[ 1.026689] io scheduler mq-deadline registered
[ 1.026703] io scheduler kyber registered
[ 1.026850] io scheduler bfq registered
[ 1.029339] samsung-usb2-phy 12130000.phy: 12130000.phy supply vbus not found, using dummy regulator
[ 1.030375] exynos5_usb3drd_phy 12100000.phy: 12100000.phy supply vbus not found, using dummy regulator
[ 1.030462] exynos5_usb3drd_phy 12100000.phy: 12100000.phy supply vbus-boost not found, using dummy regulator
[ 1.030836] exynos5_usb3drd_phy 12500000.phy: 12500000.phy supply vbus not found, using dummy regulator
[ 1.030920] exynos5_usb3drd_phy 12500000.phy: 12500000.phy supply vbus-boost not found, using dummy regulator
[ 1.039357] dma-pl330 121a0000.pdma: Loaded driver for PL330 DMAC-241330
[ 1.039373] dma-pl330 121a0000.pdma: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[ 1.042056] dma-pl330 121b0000.pdma: Loaded driver for PL330 DMAC-241330
[ 1.042072] dma-pl330 121b0000.pdma: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[ 1.042945] dma-pl330 10800000.mdma: Loaded driver for PL330 DMAC-241330
[ 1.042961] dma-pl330 10800000.mdma: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32
[ 1.111827] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.114097] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 62, base_baud = 0) is a S3C6400/10
[ 1.978573] printk: console [ttySAC2] enabled
[ 1.984530] exynos-trng 10830600.rng: Exynos True Random Number Generator.
[ 1.990845] exynos-mixer 14450000.mixer: Adding to iommu group 0
[ 1.998541] exynos-drm-g2d 10850000.g2d: Adding to iommu group 1
[ 2.004542] exynos-rotator 11c00000.rotator: Adding to iommu group 2
[ 2.016760] mali 11800000.gpu: Failed to get regulator
[ 2.020457] mali 11800000.gpu: Power control initialization failed
[ 2.037228] brd: module loaded
[ 2.053212] loop: module loaded
[ 2.055686] libphy: Fixed MDIO Bus: probed
[ 2.059315] usbcore: registered new interface driver r8152
[ 2.064485] usbcore: registered new interface driver cdc_ether
[ 2.070275] usbcore: registered new interface driver cdc_subset
[ 2.078319] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.083418] ehci-exynos: EHCI EXYNOS driver
[ 2.087898] exynos-ehci 12110000.usb: EHCI Host Controller
[ 2.093037] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1
[ 2.100908] exynos-ehci 12110000.usb: irq 79, io mem 0x12110000
[ 2.121854] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00
[ 2.126670] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04
[ 2.134652] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.141836] usb usb1: Product: EHCI Host Controller
[ 2.146687] usb usb1: Manufacturer: Linux 5.4.109 ehci_hcd
[ 2.152145] usb usb1: SerialNumber: 12110000.usb
[ 2.157310] hub 1-0:1.0: USB hub found
[ 2.160506] hub 1-0:1.0: 3 ports detected
[ 2.165381] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.170617] ohci-exynos: OHCI EXYNOS driver
[ 2.174950] exynos-ohci 12120000.usb: USB Host Controller
[ 2.180151] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2
[ 2.187883] exynos-ohci 12120000.usb: irq 79, io mem 0x12120000
[ 2.254067] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.04
[ 2.260880] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.268568] usb usb2: Product: USB Host Controller
[ 2.272833] usb usb2: Manufacturer: Linux 5.4.109 ohci_hcd
[ 2.278289] usb usb2: SerialNumber: 12120000.usb
[ 2.283432] hub 2-0:1.0: USB hub found
[ 2.286649] hub 2-0:1.0: 3 ports detected
[ 2.292745] mousedev: PS/2 mouse device common for all mice
[ 2.298054] i2c /dev entries driver
[ 2.323170] vdd_ldo9: Bringing 3300000uV into 3000000-3000000uV
[ 2.340548] vddq_mmc2: Bringing 3300000uV into 2800000-2800000uV
[ 2.361183] vdd_sd: Bringing 3300000uV into 2800000-2800000uV
[ 2.440955] s5m-rtc s2mps14-rtc: registered as rtc0
[ 2.444940] s2mps11-clk s2mps11-clk: DMA mask not set
[ 2.452376] s5p-jpeg 11f50000.jpeg: Adding to iommu group 3
[ 2.456860] s5p-jpeg 11f50000.jpeg: encoder device registered as /dev/video20
[ 2.463766] s5p-jpeg 11f50000.jpeg: decoder device registered as /dev/video21
[ 2.470710] s5p-jpeg 11f50000.jpeg: Samsung S5P JPEG codec
[ 2.476353] s5p-jpeg 11f60000.jpeg: Adding to iommu group 4
[ 2.482071] s5p-jpeg 11f60000.jpeg: encoder device registered as /dev/video22
[ 2.488982] s5p-jpeg 11f60000.jpeg: decoder device registered as /dev/video23
[ 2.495926] s5p-jpeg 11f60000.jpeg: Samsung S5P JPEG codec
[ 2.502097] s5p-mfc 11000000.codec: Adding to iommu group 5
[ 2.524680] s5p-mfc 11000000.codec: preallocated 16 MiB buffer for the firmware and context buffers
[ 2.532361] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v8.fw failed with error -2
[ 2.540973] s5p_mfc_load_firmware:69: Firmware is not present in the /lib/firmware directory nor compiled in kernel
[ 2.551507] s5p-mfc 11000000.codec: decoder registered as /dev/video10
[ 2.557997] s5p-mfc 11000000.codec: encoder registered as /dev/video11
[ 2.566384] exynos-gsc 13e00000.video-scaler: Adding to iommu group 6
[ 2.572535] exynos-gsc 13e10000.video-scaler: Adding to iommu group 7
[ 2.588293] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled
[ 2.595736] device-mapper: uevent: version 1.0.3
[ 2.600006] device-mapper: ioctl: 4.41.0-ioctl (2019-09-16) initialised: dm-devel@redhat.com
[ 2.624491] sdhci: Secure Digital Host Controller Interface driver
[ 2.629221] sdhci: Copyright(c) Pierre Ossman
[ 2.633718] Synopsys Designware Multimedia Card Interface Driver
[ 2.640072] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode.
[ 2.646446] dwmmc_exynos 12200000.mmc: Using internal DMA controller.
[ 2.652776] dwmmc_exynos 12200000.mmc: Version ID is 250a
[ 2.658166] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 81,64 bit host data width,64 deep fifo
[ 2.667591] dwmmc_exynos 12200000.mmc: allocated mmc-pwrseq
[ 2.672963] mmc_host mmc0: card is non-removable.
[ 2.694191] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[ 2.715285] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode.
[ 2.720736] dwmmc_exynos 12220000.mmc: Using internal DMA controller.
[ 2.727127] dwmmc_exynos 12220000.mmc: Version ID is 250a
[ 2.732508] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 82,64 bit host data width,64 deep fifo
[ 2.757214] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[ 2.778967] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.784580] s5p-secss 10830000.sss: s5p-sss driver registered
[ 2.789475] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.802224] exynos-nocp: new NoC Probe device registered: 10ca1000.nocp
[ 2.807487] exynos-nocp: new NoC Probe device registered: 10ca1400.nocp
[ 2.814076] exynos-nocp: new NoC Probe device registered: 10ca1800.nocp
[ 2.820657] exynos-nocp: new NoC Probe device registered: 10ca1c00.nocp
[ 2.827460] exynos-ppmu: new PPMU device registered 10d00000.ppmu (ppmu-event3-dmc0_0)
[ 2.835165] exynos-ppmu: new PPMU device registered 10d10000.ppmu (ppmu-event3-dmc0_1)
[ 2.839696] mmc_host mmc0: Bus speed (slot 0) = 200000000Hz (slot req 200000000Hz, actual 200000000HZ div = 0)
[ 2.843650] exynos-ppmu: new PPMU device registered 10d60000.ppmu (ppmu-event3-dmc1_0)
[ 2.860887] exynos-ppmu: new PPMU device registered 10d70000.ppmu (ppmu-event3-dmc1_1)
[ 2.870323] exynos5-dmc 10c20000.memory-controller: DMC initialized, in irq mode: 0
[ 2.877322] exynos-adc 12d10000.adc: IRQ index 1 not found
[ 2.887467] NET: Registered protocol family 17
[ 2.890456] NET: Registered protocol family 15
[ 2.894897] Key type dns_resolver registered
[ 2.899514] Registering SWP/SWPB emulation handler
[ 2.904008] registered taskstats version 1
[ 2.907952] Loading compiled-in X.509 certificates
[ 2.912808] Key type ._fscrypt registered
[ 2.916699] Key type .fscrypt registered
[ 2.921412] Key type encrypted registered
[ 2.957932] exynos-asv 10000000.chipid: cpu0 opp0, freq: 1500 missing
[ 2.962950] exynos-asv 10000000.chipid: cpu4 opp0, freq: 2100 missing
[ 2.971509] OF: graph: no port node found in /soc/hdmi@14530000
[ 2.977747] [drm] Exynos DRM: using 14450000.mixer device for DMA mapping operations
[ 2.984197] exynos-drm exynos-drm: bound 14450000.mixer (ops 0xc0b6dbe8)
[ 2.990753] exynos-drm exynos-drm: bound 14530000.hdmi (ops 0xc0b6e26c)
[ 2.997655] exynos-drm-g2d 10850000.g2d: The Exynos G2D (ver 4.1) successfully registered.
[ 3.005541] exynos-drm exynos-drm: bound 10850000.g2d (ops 0xc0b6f1b4)
[ 3.012150] exynos-rotator 11c00000.rotator: The exynos rotator has been probed successfully
[ 3.012665] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0)
[ 3.020452] exynos-drm exynos-drm: bound 11c00000.rotator (ops 0xc0b6fa40)
[ 3.020462] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 3.030813] mmc_host mmc0: Bus speed (slot 0) = 266666666Hz (slot req 200000000Hz, actual 133333333HZ div = 1)
[ 3.036990] [drm] No driver support for vblank timestamp query.
[ 3.059884] mmc0: new HS400 MMC card at address 0001
[ 3.065931] mmcblk0: mmc0:0001 BJTD4R 29.1 GiB
[ 3.069880] mmcblk0boot0: mmc0:0001 BJTD4R partition 1 4.00 MiB
[ 3.075737] mmcblk0boot1: mmc0:0001 BJTD4R partition 2 4.00 MiB
[ 3.081455] mmcblk0rpmb: mmc0:0001 BJTD4R partition 3 4.00 MiB, chardev (244:0)
[ 3.092554] mmcblk0: p1 p2 p3
[ 3.269510] Console: switching to colour frame buffer device 240x67
[ 3.290997] exynos-drm exynos-drm: fb0: exynosdrmfb frame buffer device
[ 3.298029] [drm] Initialized exynos 1.1.0 20180330 for exynos-drm on minor 0
[ 3.306180] mali 11800000.gpu: GPU identified as 0x0620 r0p1 status 0
[ 3.311209] mali 11800000.gpu: Protected mode not available
[ 3.317213] mali 11800000.gpu: Probed as mali0
[ 3.322625] dwc3 12000000.dwc3: Failed to get clk 'ref': -2
[ 3.327147] xhci-hcd xhci-hcd.8.auto: xHCI Host Controller
[ 3.332205] xhci-hcd xhci-hcd.8.auto: new USB bus registered, assigned bus number 3
[ 3.340059] xhci-hcd xhci-hcd.8.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000000002010010
[ 3.349234] xhci-hcd xhci-hcd.8.auto: irq 159, io mem 0x12000000
[ 3.355424] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04
[ 3.363390] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.370578] usb usb3: Product: xHCI Host Controller
[ 3.375430] usb usb3: Manufacturer: Linux 5.4.109 xhci-hcd
[ 3.380889] usb usb3: SerialNumber: xhci-hcd.8.auto
[ 3.386081] hub 3-0:1.0: USB hub found
[ 3.389465] hub 3-0:1.0: 1 port detected
[ 3.393567] xhci-hcd xhci-hcd.8.auto: xHCI Host Controller
[ 3.398832] xhci-hcd xhci-hcd.8.auto: new USB bus registered, assigned bus number 4
[ 3.406458] xhci-hcd xhci-hcd.8.auto: Host supports USB 3.0 SuperSpeed
[ 3.412994] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.421146] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.04
[ 3.424709] devfreq 11800000.gpu: Couldn't update frequency transition information.
[ 3.429244] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.429248] usb usb4: Product: xHCI Host Controller
[ 3.448914] usb usb4: Manufacturer: Linux 5.4.109 xhci-hcd
[ 3.454372] usb usb4: SerialNumber: xhci-hcd.8.auto
[ 3.459529] hub 4-0:1.0: USB hub found
[ 3.462969] hub 4-0:1.0: 1 port detected
[ 3.468515] dwc3 12400000.dwc3: Failed to get clk 'ref': -2
[ 3.472941] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[ 3.478090] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 5
[ 3.485960] xhci-hcd xhci-hcd.9.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000000002010010
[ 3.495123] xhci-hcd xhci-hcd.9.auto: irq 160, io mem 0x12400000
[ 3.501296] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04
[ 3.509279] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.516469] usb usb5: Product: xHCI Host Controller
[ 3.521323] usb usb5: Manufacturer: Linux 5.4.109 xhci-hcd
[ 3.526780] usb usb5: SerialNumber: xhci-hcd.9.auto
[ 3.531925] hub 5-0:1.0: USB hub found
[ 3.535375] hub 5-0:1.0: 1 port detected
[ 3.539453] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[ 3.544722] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 6
[ 3.552345] xhci-hcd xhci-hcd.9.auto: Host supports USB 3.0 SuperSpeed
[ 3.558883] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.566987] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.04
[ 3.575137] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.582326] usb usb6: Product: xHCI Host Controller
[ 3.587177] usb usb6: Manufacturer: Linux 5.4.109 xhci-hcd
[ 3.592637] usb usb6: SerialNumber: xhci-hcd.9.auto
[ 3.597777] hub 6-0:1.0: USB hub found
[ 3.601232] hub 6-0:1.0: 1 port detected
[ 3.606039] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling
[ 3.610754] rtc rtc1: invalid alarm value: 1900-01-21T00:00:00
[ 3.616578] s3c-rtc 101e0000.rtc: registered as rtc1
[ 3.622941] exynos-bus: new bus device registered: soc:bus_wcore ( 84000 KHz ~ 400000 KHz)
[ 3.630251] exynos-bus: new bus device registered: soc:bus_noc ( 67000 KHz ~ 100000 KHz)
[ 3.638161] exynos-bus: new bus device registered: soc:bus_fsys_apb (100000 KHz ~ 200000 KHz)
[ 3.646550] exynos-bus: new bus device registered: soc:bus_fsys (100000 KHz ~ 200000 KHz)
[ 3.654849] exynos-bus: new bus device registered: soc:bus_fsys2 ( 75000 KHz ~ 150000 KHz)
[ 3.663190] exynos-bus: new bus device registered: soc:bus_mfc ( 96000 KHz ~ 333000 KHz)
[ 3.671191] exynos-bus: new bus device registered: soc:bus_gen ( 89000 KHz ~ 267000 KHz)
[ 3.679138] exynos-bus: new bus device registered: soc:bus_peri ( 67000 KHz ~ 67000 KHz)
[ 3.687448] exynos-bus: new bus device registered: soc:bus_g2d ( 84000 KHz ~ 333000 KHz)
[ 3.695468] exynos-bus: new bus device registered: soc:bus_g2d_acp ( 67000 KHz ~ 267000 KHz)
[ 3.703856] exynos-bus: new bus device registered: soc:bus_jpeg ( 75000 KHz ~ 300000 KHz)
[ 3.712007] exynos-bus: new bus device registered: soc:bus_jpeg_apb ( 84000 KHz ~ 167000 KHz)
[ 3.720399] exynos-bus: new bus device registered: soc:bus_disp1_fimd (120000 KHz ~ 200000 KHz)
[ 3.729105] exynos-bus: new bus device registered: soc:bus_disp1 (120000 KHz ~ 300000 KHz)
[ 3.737344] exynos-bus: new bus device registered: soc:bus_gscl_scaler (150000 KHz ~ 300000 KHz)
[ 3.746223] exynos-bus: new bus device registered: soc:bus_mscl ( 84000 KHz ~ 400000 KHz)
[ 3.757656] s5m-rtc s2mps14-rtc: setting system clock to 2021-07-19T10:11:10 UTC (1626689470)
[ 3.790351] ALSA device list:
[ 3.791839] No soundcards found.
[ 3.796229] Freeing unused kernel memory: 1024K
[ 3.802031] Run /init as init process
[ 3.881987] usb 4-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd
[ 3.887257] EXT4-fs (mmcblk0p3): recovery complete
[ 3.892832] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null)
[ 3.910845] usb 4-1: New USB device found, idVendor=05e3, idProduct=0616, bcdDevice=22.23
[ 3.917554] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.924654] usb 4-1: Product: USB3.0 Hub
[ 3.928585] usb 4-1: Manufacturer: GenesysLogic
[ 3.950865] /dev/loop0: Can't open blockdev
[ 3.954182] /dev/loop0: Can't open blockdev
[ 3.957862] hub 4-1:1.0: USB hub found
[ 3.961827] hub 4-1:1.0: 2 ports detected
[ 4.033851] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[ 4.192603] usb 3-1: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=22.23
[ 4.199310] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 4.206454] usb 3-1: Product: USB2.0 Hub
[ 4.210325] usb 3-1: Manufacturer: GenesysLogic
[ 4.277051] usb 4-1.1: new SuperSpeed Gen 1 USB device number 3 using xhci-hcd
[ 4.282914] hub 3-1:1.0: USB hub found
[ 4.286796] hub 3-1:1.0: 2 ports detected
[ 4.302814] usb 4-1.1: New USB device found, idVendor=0781, idProduct=5583, bcdDevice= 1.00
[ 4.309706] usb 4-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4.317045] usb 4-1.1: Product: SanDisk 3.2Gen1
[ 4.321594] usb 4-1.1: Manufacturer: USB
[ 4.325567] usb 4-1.1: SerialNumber: 0101584b1850411093e248f64aaf1786c058a1878ee9fa82adba44f6c2aac72eabc90000000000000000000098b924c2ff89190083558107432b5cdf
[ 4.627549] hwmon hwmon0: fan_speeds : set_fan_speed [102 140 178 252]
[ 4.632725] usb 3-1.2: new high-speed USB device number 3 using xhci-hcd
[ 4.743162] usb 3-1.2: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=32.98
[ 4.750052] usb 3-1.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 4.754061] usb 6-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd
[ 4.757334] usb 3-1.2: Product: USB2.0 Hub
[ 4.782863] usb 6-1: New USB device found, idVendor=0bda, idProduct=8153, bcdDevice=30.00
[ 4.789612] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[ 4.796736] usb 6-1: Product: USB 10/100/1000 LAN
[ 4.801400] usb 6-1: Manufacturer: Realtek
[ 4.805492] usb 6-1: SerialNumber: 000001000000
[ 4.821312] hub 3-1.2:1.0: USB hub found
[ 4.825171] hub 3-1.2:1.0: 4 ports detected
[ 4.831455] udevd[228]: starting version 3.2.9
[ 4.846954] random: udevd: uninitialized urandom read (16 bytes read)
[ 4.852043] random: udevd: uninitialized urandom read (16 bytes read)
[ 4.858650] random: udevd: uninitialized urandom read (16 bytes read)
[ 4.879192] udevd[230]: starting eudev-3.2.9
[ 4.993168] gpiomem-exynos 13400000.gpiomem: Initialised: GPIO register area is 2
[ 4.999815] gpiomem-exynos 13400000.gpiomem: Initialised: Registers at 0x13400000
[ 5.008539] input: gpio_keys as /devices/platform/gpio_keys/input/input0
[ 5.015956] gpiomem-exynos 13400000.gpiomem: Initialised: Registers at 0x14010000
[ 5.031225] usb 6-1: reset SuperSpeed Gen 1 USB device number 2 using xhci-hcd
[ 5.102922] r8152 6-1:1.0 eth0: v1.10.11
[ 5.177906] usb 3-1.2.1: new full-speed USB device number 4 using xhci-hcd
[ 5.251639] SCSI subsystem initialized
[ 5.258262] usb-storage 4-1.1:1.0: USB Mass Storage device detected
[ 5.264306] scsi host0: usb-storage 4-1.1:1.0
[ 5.268840] usbcore: registered new interface driver usb-storage
[ 5.276823] usbcore: registered new interface driver uas
[ 5.295135] usb 3-1.2.1: New USB device found, idVendor=045e, idProduct=028e, bcdDevice= 1.14
[ 5.302292] usb 3-1.2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 5.309905] usb 3-1.2.1: Product: Controller
[ 5.313956] usb 3-1.2.1: Manufacturer: ©Microsoft Corporation
[ 5.319738] usb 3-1.2.1: SerialNumber: 065F3FE
[ 5.343685] dma-pl330 3880000.adma: Loaded driver for PL330 DMAC-241330
[ 5.348854] dma-pl330 3880000.adma: DBUFF-4x8bytes Num_Chans-6 Num_Peri-16 Num_Events-6
[ 5.357679] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s
[ 5.367148] odroid-audio sound: snd-soc-dummy-dai <-> samsung-i2s mapping ok
[ 5.372776] odroid-audio sound: i2s-hifi <-> snd-soc-dummy-dai mapping ok
[ 5.380327] odroid-audio sound: snd-soc-dummy-dai <-> samsung-i2s-sec mapping ok
[ 5.387002] dma-pl330 3880000.adma: PM domain MAU will not be powered off
[ 5.565882] input: Microsoft X-Box 360 pad as /devices/platform/soc/soc:usb3-0/12000000.dwc3/xhci-hcd.8.auto/usb3/3-1/3-1.2/3-1.2.1/3-1.2.1:1.0/input/input1
[ 5.578677] usbcore: registered new interface driver xpad
[ 6.270695] scsi 0:0:0:0: Direct-Access USB SanDisk 3.2Gen1 1.00 PQ: 0 ANSI: 6
[ 6.281190] sd 0:0:0:0: [sda] 240353280 512-byte logical blocks: (123 GB/115 GiB)
[ 6.287549] sd 0:0:0:0: [sda] Write Protect is off
[ 6.291980] sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00
[ 6.292327] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 6.328906] sda: sda1
[ 6.328912] random: crng init done
[ 6.333187] random: 5 urandom warning(s) missed due to ratelimiting
[ 6.340586] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 6.984094] Bluetooth: Core ver 2.22
[ 6.986528] NET: Registered protocol family 31
[ 6.990741] Bluetooth: HCI device and connection manager initialized
[ 6.997003] Bluetooth: HCI socket layer initialized
[ 7.001832] Bluetooth: L2CAP socket layer initialized
[ 7.006891] Bluetooth: SCO socket layer initialized
[ 7.056938] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 7.060831] Bluetooth: BNEP filters: protocol multicast
[ 7.066009] Bluetooth: BNEP socket layer initialized
[ 7.084508] 8021q: 802.1Q VLAN Support v1.8
[ 7.130559] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 7.168849] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 7.565291] fuse: init (API version 7.31)
[ 8.744147] r8152 6-1:1.0 eth0: carrier on
[ 10.200256] usbcore: registered new interface driver usbhid
[ 10.204365] usbhid: USB HID core driver
[ 10.556284] NET: Registered protocol family 10
[ 10.560378] Segment Routing with IPv6
[ 35.806311] vdd_ldo12: disabling
#
@davidb2111 said in Retour 7.2.2 sur XU4:
@cedric-debuiselle said in Retour 7.2.2 sur XU4:
@davidb2111
/boot$ dmesg | grep fb
[ 3.336086] exynos-drm exynos-drm: fb0: exynosdrmfb frame buffer devicedit moi je voudrais mettre une signature comme toi sur mon profil j'arrive pas à trouver où sais
Arg, le module tft n'est pas chargé. Tu pourrais m'envoyer le résultat de la commande
dmesg, ton fichier/boot/boot.iniet ton fichier/boot/config.ini, stp ?
boot.ini
ODROIDXU-UBOOT-CONFIG # U-Boot Parameters (DO NOT MODIFY) setenv version 4.14 setenv zimage boot/linux setenv fdtbin boot/exynos5422-odroidxu4.dtb setenv uInitrd boot/uInitrd # --- Screen Configuration for HDMI --- # # --------------------------------------- # Uncomment only ONE line! Leave all commented for automatic selection. # Uncomment only the setenv line! # --------------------------------------- # ODROID-VU forced resolution # setenv videoconfig "video=HDMI-A-1:1280x800@60" # ----------------------------------------------- # ODROID-VU forced EDID # setenv videoconfig "drm_kms_helper.edid_firmware=edid/1280x800.bin" # ----------------------------------------------- # 1920x1080 (1080P) with monitor provided EDID information. (1080p-edid) setenv videoconfig "video=HDMI-A-1:1920x1080@60" # ----------------------------------------------- # 1920x1080 (1080P) without monitor data using generic information (1080p-noedid) # setenv videoconfig "drm_kms_helper.edid_firmware=edid/1920x1080.bin" # ----------------------------------------------- # 1920x1080 50hz (1080P) with monitor provided EDID information. (1080p 50hz-edid) # setenv videoconfig "video=HDMI-A-1:1920x1080@50" # ----------------------------------------------- # 1920x1080 50hz (1080P) without monitor data using generic information (1080p 50hz-noedid) # setenv videoconfig "drm_kms_helper.edid_firmware=edid/1920x1080_50hz.bin" # ----------------------------------------------- # 1440x900 with monitor provided EDID information. # setenv videoconfig "video=HDMI-A-1:1440x900@60" # ----------------------------------------------- # 1440x900 without monitor data using generic information # setenv videoconfig "drm_kms_helper.edid_firmware=edid/1440x900.bin" # ----------------------------------------------- # 1280x1024 without monitor data using generic information # setenv videoconfig "drm_kms_helper.edid_firmware=edid/1280x1024.bin" # ----------------------------------------------- # 1280x720 (720P) with monitor provided EDID information. (720p-edid) # setenv videoconfig "video=HDMI-A-1:1280x720@60" # ----------------------------------------------- # 1280x720 (720P) without monitor data using generic information (720p-noedid) # setenv videoconfig "drm_kms_helper.edid_firmware=edid/1280x720.bin" # ----------------------------------------------- # 1024x768 without monitor data using generic information # setenv videoconfig "drm_kms_helper.edid_firmware=edid/1024x768.bin" # ----------------------------------------------- # 1024x600 without monitor data using generic information (ODROID VU7+) # setenv videoconfig "drm_kms_helper.edid_firmware=edid/1024x600.bin" # ----------------------------------------------- # 800x600 without monitor data using generic information # setenv videoconfig "drm_kms_helper.edid_firmware=edid/800x600.bin" # ----------------------------------------------- # 800x480 without monitor data using generic information (ODROID 7") # setenv videoconfig "drm_kms_helper.edid_firmware=edid/800x480.bin" # ----------------------------------------------- # 720x576 without monitor data using generic information # setenv videoconfig "drm_kms_helper.edid_firmware=edid/720x576.bin" # ----------------------------------------------- # 720x480 without monitor data using generic information # setenv videoconfig "drm_kms_helper.edid_firmware=edid/720x480.bin" # ----------------------------------------------- # 640x480 without monitor data using generic information # setenv videoconfig "drm_kms_helper.edid_firmware=edid/640x480.bin" # --- HDMI / DVI Mode Selection --- # ------------------------------------------ # - HDMI Mode setenv vout "hdmi" # - DVI Mode (disables sound over HDMI as per DVI compat) # setenv vout "dvi" # --- CPU Governor Setup --- # Uncomment only one line. New governor is set after 90secs after boot. # ------------------------------------------ # - Performance (Keep all the CPU's at Maximum frequency) setenv governor "performance" # ------------------------------------------ # - Ondemand # setenv governor "ondemand" # ------------------------------------------ # - Interactive (Pretty much just like ondemand with more possible customization via sysfs.) # setenv governor "interactive" # ------------------------------------------ # - Conservative (Like ondemand, but do the frequency transitions more slowly, great for battery powered applications) # setenv governor "conservative" # ------------------------------------------ # - Powersave (Keeps the CPU's to the lowest possible temps) # setenv governor "powersave" # --- HDMI CEC Configuration --- # ------------------------------------------ setenv cecenable "false" # false or true # set to true to enable HDMI CEC #------------------------------------------------------------------------------ # # HDMI Hot Plug detection # #------------------------------------------------------------------------------ # # Forces the HDMI subsystem to ignore the check if the cable is connected or # not. # false : disable the detection and force it as connected. # true : let cable, board and monitor decide the connection status. # # default: true # #------------------------------------------------------------------------------ setenv HPD "false" setenv hdmi_phy_control "HPD=${HPD} vout=${vout}" setenv dtb_addr_r "0x44000000" setenv dtbo_addr_r "0x48000000" setenv zimage_addr_r 0x40008000 setenv uInitrd_addr_r 0x42000000 setenv fdtbin_addr_r 0x44000000 setenv config_addr_r "0x4B000000" setenv fdt_high "0xffffffff" # load config.ini load mmc 0:1 ${config_addr_r} config.ini \ && ini generic ${config_addr_r} # DRAM Frequency (lpddr3 available frequency list - 933/825/728/633) setenv ddr_freq 933 # set DDR frequency dmc ${ddr_freq} # Default boot arguments setenv bootrootfs "label=RECALBOX" setenv console "console=ttySAC2,115200n8 consoleblank=0 vt.global_cursor_default=0" # boot commands fatload mmc 0:1 ${zimage_addr_r} ${zimage} fatload mmc 0:1 ${uInitrd_addr_r} ${uInitrd} fatload mmc 0:1 ${fdtbin_addr_r} ${fdtbin} fdt addr ${dtb_addr_r} if test "${cecenable}" = "false"; then fdt rm /cec@101B0000; fi setenv bootargs "${bootrootfs} ${console} governor=${governor} ${videoconfig} ${hdmi_phy_control}" # load overlays from config.ini if test "x${overlay_profile}" != "x"; then ini overlay_${overlay_profile} ${config_addr_r} fi if test "x{overlays}" != "x"; then fdt resize ${overlay_resize} for overlay in ${overlays}; do load mmc 0:1 ${dtbo_addr_r} overlays/${overlay}.dtbo \ && fdt apply ${dtbo_addr_r} done fi bootz ${zimage_addr_r} ${uInitrd_addr_r} ${fdtbin_addr_r}
config.ini
[generic] ; Device Tree Overlay overlay_resize=16384 ; uncomment next line to enable Odroid XU4 OGST overlay_profile=hktft_cs_ogst overlays="spi0 i2c0 i2c1 uart0" [overlay_hktft_cs_ogst] overlays="hktft-cs-ogst i2c0"
@davidb2111 @cedric-debuiselle toujours pas de solution sur notre problème ?
@manitou said in Retour 7.2.2 sur XU4:
@davidb2111 @cedric-debuiselle toujours pas de solution sur notre problème ?
Non toujours pas de nouvelles
@manitou @cedric-debuiselle
Pouvez-vous essayer de taper la commande:
modprobe fb_hktft32 /etc/init.d/S32miniTFT stop /etc/init.d/S32miniTFT start
@davidb2111 said in Retour 7.2.2 sur XU4:
@manitou @cedric-debuiselle
Pouvez-vous essayer de taper la commande:
modprobe fb_hktft32 /etc/init.d/S32miniTFT stop /etc/init.d/S32miniTFT start
# modprobe fb_hktft32 # /etc/init.d/S32miniTFT stop Stopping tft support start-stop-daemon: warning: killing process 979: No such process # /etc/init.d/S32miniTFT start #
@davidb2111 said in Retour 7.2.2 sur XU4:
@cedric-debuiselle
Normalement, si l'OGST est détecté, tu devrais avoir un fichier système/dev/fb1
Tu peux lui envoyer des données brutes avec la commandedd, je pense.
j'ai l'impression qu'on a un soucis de détection de l'écran, normalement je devrais d'après se que tu me dit un fichier fb1, dans l'emplacement fichier racine dev/, j'en ai aucun
