Testers wanted: major system upgrade (Pi3b+, KODI 17 and much more ...)

[voljega]

@Substring bon y'a beaucoup de mieux sur la GPD Win :

• l'image s'affiche et je peux naviguer dans ES sans problème mais c'est pivoté à 90° (enfin c'est le sens natif de l'écran)
• le gamepad intégré est bien reconnu et déjà mappé (au moins start, select, pad, a et b)
• le clavier n'est pas reconnu bizarrement
• quelquesoit le système, il y a retour au menu dès que j'essaye de lancer un jeu (testé que les jeux intégrés)
• plus chiant ma clé ethernet USB pluggable qui était parfaitement reconnue avant ne l'est plus du tout maintenant
• je peux pas me connecter en wifi car le clavier virtuel n'est affiché qu'à moitié (alors que les menus start et select sont affichés en entier)
• donc pas de wifi, pas d'ethernet, ça va être chaud pour la suite des opérations.... j'vais essayer avec parangon ExtFS

EDIT :
an ajoutant xrandr -o right dans /etc/X11/xinit/xinitrc j'ai bien l'image qui bascule correctement par contre elle est en bas à gauche et je ne vois que le 1/5ème supérieur...

pas trop moyen d'aller plus loin pour l'instant, ptet qu'il faut forcer le 720p dans xinitrc mais alors j'en sais foutre rien comment faire

[paradadf]

@voljega lets follow the instructions and keep this thread in english please.

[azvarel]

@Substring

I tested with the joystick snes30 8bitdo, XBOX 360 with receiver and the only problem I noticed is that it does not work on kodi 17

https://file.ac/Y2lQtQzh2FM/

[0x77696e]

@substring I tell you a fresh report : https://file.ac/oJYDOq7Jgr4/ maybe it can help

[0x77696e]

@Substring but WTH, why all is working after rebooting ES.....

[Substring]

@voljega you must remap controls, there were some changes that made remapping mandatory. I'll try to circumvent this, as the change is mistly important to kodi

[Substring]

@azvarel which pad doesn't work ? So far i've tested with a x360 copy and a 8bitdo nes30, both working fine

[Substring]

@0x77696e i haven't had time to dig through your problem for now

[azvarel]

@substring said in Testers wanted: major system upgrade (Pi3b+, KODI 17 and much more ...):

which pad doesn't work ? So far i've tested with a x360 copy and a 8bitdo nes30, both working fine

the two joysticks (x360 and snes30) do not work only in kodi, ES and retroarch work perfectly fine

[Substring]

@azvarel try renaming ~/.kodi just to see then launch again kodi. Have ypu remapped ypur pads ?

[Gaetan]

@Substring En éteignant Recalbox, je reste coincé sur l'écran noir avec le petit logo en bas au milieu avec la ref de la version. Je suis obligé de débrancher à l'arrache car je n'ai plus accès au webmanager.
https://file.ac/RbrTVhWvK3Q/

[voljega]

@substring unless it prevents emulators to display, I have no problem at all with controls ?

[Substring]

@gaetan is ypur share on your sd card ?

[Substring]

@voljega configgen crashes if pads are not remapped ad there are some new values stored + normalized buttons order between sdl2, retroarch and the joypad plugin for kodi

[Gaetan]

@Substring Yes it is, a Sandisk 128go sd card.
Sorry for my french comment above, mixing languages all the day can be tricky.

[Substring]

@azvarel looking at your support archive, you haven't remapped your x360 pad, which you MUST do

[Substring]

@0x77696e So, a few questions :

• was it working before the upgrade ?
• have you set a particular videomode to es ?
• can you make a support archive WHEN you stuc after leaving kodi ? I'm curious about ES state + screen resolution.

Kodi should run at the native resolution of your projector, which should be the same resolution as ES. Tricky ...

[azvarel]

@azvarel try renaming ~/.kodi just to see then launch again kodi. Have ypu remapped ypur pads ?

@substring
yes, I had mapped the buttons, renamed ~/.kodi and did not get exite the joystick did not work except the B, A and R buttons.

I managed to solve the following command: in KODI I went into System Settings > Input > Configure attached conttrollers and add Super Nintendo joystick through the button Get more...

after remapping this control by kodi, the 8bitdo snes30, started to work.
maybe required for the official version, have this option as default

[0x77696e]

@substring I have used the already upgraded image, so I can't tell you if it was running before (and this is the first beta release running on rpi3+).
I have not set anything on ES, it is the stock configuration.
The support archive I have submitted is already when the bug occurs.
But.. in fact, kodi AND ES are working and there are no resolution problems, if I starts from ES and then Kodi, all is working great.
The bug apears when I'm leaving Kodi and the system returns back to ES, here the screen is cropped.

[stefankrantz]

@Substring

Brand new RPI3+ here with a fresh sd-card.
Just had a few hours to test, but most of the things seems to be working fine.
I ran into one strange thing with my PS3-controller though.
I know people have been reporting some issues with PS3-controllers, but remapping is not working here.
As long as the controller is connected with a wired USB-cable it responds as it should, I can navigate the ES-menus and it responds with the proper action to my keypresses.
When i unplug the USB-cable and it connects over Bluetooth down-buttons triggers A, and two presses down launches a game. That fails. And after that all game fails until next reboot. Just a blank black screen and then return to ES. Before connecting PS3-controller over bluetooth all games work and after a reboot they work again.

Also - Recalbox reports that RPI3+ is runs on 1200 MHz, not 1350 as it should?

Connected both wifi and bluetooth controllers with the embedded wifi and bluetooth that came with the RPi and it works like a charm. Also my two 8bitDo SFC30-controllers works perfect.