[PROJECT] JAMMA-Pi

[Substring]

Adding SPI to the gpio driver is quite a big task

[aTg]

@substring Can I offer a bounty to contirbute to the Recalbox project?

[llegoff]

Hello,
I have not tested, but there is an overlay to reroute the pins cs0 and cs1.

see on /boot/overlay/readme :

Name: spi0-cs
Info: Allows the (software) CS pins for SPI0 to be changed
Load: dtoverlay=spi0-cs,<param>=<val>
Params: cs0_pin GPIO pin for CS0 (default
cs1_pin GPIO pin for CS1 (default 7)

put in /boot/config.txt , the line :

dtoverlay=spi0-cs, cs0_pin <n°pin>

there is another way : software i2c with dtoverlay i2c-gpio

Name: i2c-gpio
Info: Adds support for software i2c controller on gpio pins
Load: dtoverlay=i2c-gpio,<param>=<val>
Params: i2c_gpio_sda GPIO used for I2C data (default "23")
i2c_gpio_scl GPIO used for I2C clock (default "24")
i2c_gpio_delay_us Clock delay in microseconds
(default "2" = ~100kHz)

[aTg]

@llegoff I'm going to discard the SPI prorotype and make another based on i2c because I think with this bus is possible move all the pins.

Thanks for your participation.

[aTg]

Well I'm back again with the project, following the recomendations of @Substring I change the prototype to allow one MCP23017 conected by the port i2c to talk with Recalbox, I add to the circuit one RGB-Pi PCB for the video output and here is the little frankenstein.

I use the overlay i2c-gpio to move the pins from 2, 3 to 10 , 11

dtparam=i2c_arm=on
dtoverlay=i2c-gpio,i2c_gpio_sda=10,i2c_gpio_scl=11

Now is the moment to enable the option en recalbox.conf, I thing the work is made by mk_arcade_joystick_rpi included but I read in the repo "The branch hotkeybtn now support one more button per player in place of MCP23017 support" and the scheme don't show any pin for i2c, this would be say not longuer avaible use i2c for controllers?

I try to activate on recalbox.conf

 # ------------ D2 - GPIO Controllers ------------ #
## GPIO Controllers
## enable controllers on GPIO with mk_arcarde_joystick_rpi (0,1)
controllers.gpio.enabled=1
## mk_gpio arguments, map=1 for one controller, map=1,2 for 2 (map=1,map=1,2)
controllers.gpio.args=map=1

But the program interfiring with the video output, and I don see what can be user to talk by i2c...

I need a little help from the Devs to talk with Recalbox by i2c and pins 10 & 11, any help is much apreciated!

[Substring]

@atg i2cdetect ?

[Substring]

Anyway, the module needs some more parameters in the recalbox.conf, see https://github.com/recalbox/mk_arcade_joystick_rpi#more-joysticks-case--mcp23017

[aTg]

@substring said in [PROJECT] JAMMA-Pi:

@atg i2cdetect ?

I thing i2cdetect don't detect nothing, I got this message:

     0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
00:          -- -- -- -- -- -- -- -- -- -- -- -- -- 
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
70: -- -- -- -- -- -- -- --                

I follow the steps from the readme, my setup on the addresses of the chips in A0 A1 A2 are 000 in one and 100 in the other, I try only with one chip on 000 and the same result, when a run modprobe mk_arcade_joystick_rpi map=1,0x20 the i2c port is enabled on pin 2 or 3 and not on 10, 11 and lose the sincronism of the image.

This can be made because the driver acces to the ports by harware and don't use the DeviceTreeOverlays.

[Substring]

@ian57 would you ever have some time to take a look at i2c gpio remapping and the kmk_arcade_gpio module ?

[ian57]

@substring ok will do that during christmas holydays
I will have som etime. please remind me through Slack or I will put an issue

[aTg]

While I'm waiting for @ian57 to look at the problem on the repo of moving the pins, I'm going to continue with the sound section.

After investigating different options and see which speakers have the most arcade machines that are usually 8 Ohms and between 10 or 15w I think there are two clear options to choose from.

We have the TDA2003 that is a mono amplifier of 10w and option number two is the TDA2005 which is a stereo amplifier of 10w per channel and can be configured in bridging mode getting 20w mono.

The interesting thing about the second option would be in the case of MVS machines that had a stereo wiring in the jamma, could change from 20w mono to stereo 10w + 10w playing with some jumpers and have compatibility with jamma and mvs.

I'm going to prototype two amplifiers and try to configure them with the minimum number of components.

One thing that f**k me a lot is that the encapsulates are not SMD and they should be soldered by hand, they are also upright and they are very ugly, it has occurred to me to knock them down and use the PCB as a heatsink, later also It could be placed on the back of the PCB to save space.

What do you think is more interesting in terms of power? Maybe 20w is too much? The pc2jamma adapter works with a TDA2003.

[aTg]

@ian57 Any new? I'm working on the others parts of the circuit but the buttons are the most important.