Tout Recalbox 6.0 au ralenti en composite.

marcus_972 · 14 Apr 2019, 12:27

Salut,

@Gia et @Mikaeru, envoyez moi vos config.txt et recalbox.conf afin que je puisse faire des tests sur mon installation. Je passe par une péritel en RGB, je peux peut être réussir à reproduire le même bug.

Mikaeru · 14 Apr 2019, 13:49

@marcus_972 Je te remercie de nous aidez pour notre souci:

mon fichier config.txt :

 # uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1
 
#disable_overscan=1
 
# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1
 
# comment to get jack audio
#hdmi_drive=2
 
# Using /etc/modules is deprecated and no longer supported on 4.4 kernel
# So manually enable audio
dtparam=audio=on
 
#config_hdmi_boost=0
 
# force hdmi while the tv can take time before sending the signal on the hdmi output
#hdmi_force_hotplug=1
 
# uncomment for composite PAL
#sdtv_mode=2
 
# uncomment for lirc-rpi
#dtoverlay=lirc-rpi
 
# if you plug your tv at the same time as your rpi and that the rpi switches from the hdmi or give a low resolution because tv had no enough time to initialize it
#boot_delay=3
 
# uncomment if you don't want the rainbow at startup
#disable_splash=1
 
# default CEC name
cec_osd_name=recalbox
 
# Overclock
gpu_mem_256=128
gpu_mem_512=256
gpu_mem_1024=512
 
avoid_safe_mode=1
 
kernel=zImage
 
# Raspyboy
dtoverlay=pwm-2chan,pin=18,func=2,pin2=13,func2=4
overscan_left=-6
overscan_right=-6
overscan_top=-15
overscan_bottom=-15
framebuffer_width=320
framebuffer_height=240
 
# Raise the first security limit up to 70° instead of 60°
temp_soft_limit=70
arm_freq=950
core_freq=250
sdram_freq=450
force_turbo=0
over_voltage=6
over_voltage_sdram_p=0
over_voltage_sdram_i=0
over_voltage_sdram_c=0
gpu_freq=250
sdram_schmoo=0x02000020

EDIT Modo : l'ajout de "```" avant et après un un block permet une meilleurs lisibilité

Mikaeru · 14 Apr 2019, 13:49

@marcus_972 et le recalbox.conf

 # System Variable
# You can configure your recalbox from here
# To set a variable, remove the first ; on the line
 
 
# ------------ A - System Options ----------- #
#    Uncomment the system.power.switch you use
;system.power.switch=ATX_RASPI_R2_6      # http://lowpowerlab.com/atxraspi/#installation
;system.power.switch=MAUSBERRY           # http://mausberry-circuits.myshopify.com/pages/setup
;system.power.switch=REMOTEPIBOARD_2003  # http://www.msldigital.com/pages/support-for-remotepi-board-2013
;system.power.switch=REMOTEPIBOARD_2005  # http://www.msldigital.com/pages/support-for-remotepi-board-plus-2015
;system.power.switch=WITTYPI             # http://www.uugear.com/witty-pi-realtime-clock-power-management-for-raspberry-pi
;system.power.switch=PIN56ONOFF          # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)
;system.power.switch=PIN56PUSH           # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)
;system.power.switch=PIN356ONOFFRESET    # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)
;system.power.switch=PIN356PUSHRESET     # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)
## fbcp FrameBuffer Copy Program
## For small TFT screen on GPIO and SPI
## See https://github.com/recalbox/recalbox-os/wiki/Utility---Use-of-fbcp-for-small-TFT-screen-%28EN%29 for details
## Needed for Waveshare 3.2" 3.5" TFT screen, 2.8" Adafruit screen
## See https://github.com/recalbox/recalbox-os/wiki/TFT-Screen-SPI-Bus-%28EN%29
## for support and configuration details needed by /boot/config.txt
system.fbcp.enabled=0
## Splash screen duration
## 0: Video will be played for 20 seconds (default)
## -1: All the video will be played (it won't be stopped automatically)
## >0 : Time before the video will be stopped (in seconds)
system.splash.length=0
## Recalbox Manager (http manager)
system.manager.enabled=1
## 1 or 2, depending on the manager version you wish
system.manager.version=2
## Recalbox security
# enforce security
# samba password required
# disable virtual gamepads
system.security.enabled=0
## Recalbox API (REST)
system.api.enabled=0
## Allow a specific resolution for ES only from the command : tvservice -m [MODE]
## Leave commented for the default usual behaviour
;system.es.videomode=CEA 4 HDMI
## EmulationStation
### menu style
### default -> default all options menu
### none -> no menu except the game search menu
### bartop -> less menu, only needed for bartops
emulationstation.menu=default
### Select a system to show on boot (use rom directory name) (string)
emulationstation.selectedsystem=favorites
### Show the gamelist of the first or selected system on boot (0,1)
emulationstation.bootongamelist=0
### Disable system view. ES will boot and show ONLY the first or selected system (0,1)
emulationstation.hidesystemview=0
### Pa&ast;&ast;e Gamelists only. Show only games listed in gamelist.xml files (0,1)
emulationstation.gamelistonly=0
### Force basicgameList view to be displayed, even if your game systems are scraped (0,1)
emulationstation.forcebasicgamelistview=0
## Emulator special keys
## default -> default all special keys
## nomenu -> cannot popup the emulator menu
## none -> no special keys in emulators
system.emulators.specialkeys=default
## Show or hide kodi in emulationstation (0,1)
kodi.enabled=1
## Start kodi at launch (0,1)
kodi.atstartup=0
## set x button shortcut (0,1)
kodi.xbutton=1
## Allow a specific resolution for Kodi only from the command : tvservice -m [MODE]
## By default is using the default resolution of your screen
kodi.videomode=default
## Kodi can wait for a network component before starting
## waithost is the ip or hostname that must answer to a ping to validate the availability
## waittime is the maximum time waited when kodi boots
## if waitmode is required, kodi will not start if the component is not available
## if waitmode is wish, kodi will start if the component is not available
## if waitmode is not set or has another value, kodi will start immediately
;kodi.network.waitmode=required
;kodi.network.waittime=10
;kodi.network.waithost=192.168.0.50
## Hyperion
## Hyperion allows you to use an ambilight like led system on your recalbox
## Use hypercon to create your configuration file, and copy it in /recalbox/share/system/configs/hyperion/hyperion.config.json
hyperion.enabled=0
 
# ------------ B - Network ------------ #
## Set system hostname
system.hostname=RASPIBOY
## Activate wifi (0,1)
wifi.enabled=1
## Set wifi region
## More info here: https://github.com/recalbox/recalbox-os/wiki/Wifi-country-code
wifi.region=US
## Wifi SSID (string)
wifi.ssid=SosoMike
## Wifi KEY (string)
## after rebooting the recalbox, the "new key" is replace by a hidden value "enc:xxxxx"
## you can edit the "enc:xxxxx" value to replace by a clear value, it will be updated again at the following reboot
## Escape your special chars (# ; $) with a backslash : $ => \$
wifi.key=enc:U2FsdGVkX1/ie4wOQL7Q17zvzz8pdPweQjzqHjYtlPQ=
## Wifi - static IP
## if you want a static IP address, you must set all 3 values (ip, gateway, and netmask)
## if any value is missing or all lines are commented out, it will fall back to the
## default of DHCP
;wifi.ip=manual ip address
;wifi.gateway=new gateway
;wifi.netmask=new netmask
# secondary wifi (not configurable via the user interface)
;wifi2.ssid=new ssid
;wifi2.key=new key
# defaults to dhcp. uncomment for static ip
;wifi2.ip=manual ip address
;wifi2.gateway=new gateway
;wifi2.netmask=new netmask
# third wifi (not configurable via the user interface)
;wifi3.ssid=new ssid
;wifi3.key=new key
# defaults to dhcp. uncomment for static ip
;wifi3.ip=manual ip address
;wifi3.gateway=new gateway
;wifi3.netmask=new netmask
## Samba share
system.samba.enabled=1
### Virtual Gamepads
system.virtual-gamepads.enabled=1
### SSH
system.ssh.enabled=1
# ------------ C - Audio ------------ #
## Set the audio device (auto, hdmi, jack)
audio.device=auto
## Set system volume (0..100)
audio.volume=90
## Enable or disable system sounds in ES (0,1)
audio.bgmusic=1
 
 
# -------------- D - Controllers ----------------- #
# Enable support for standard bluetooth controllers
controllers.bluetooth.enabled=1
 
## Please enable only one of these
# -------------- D1 - PS3 Controllers ------------ #
##Enable PS3 controllers support
controllers.ps3.enabled=1
## Choose a driver between bluez, official and shanwan
## bluez -> bluez 5 + kernel drivers, support official and shanwan sisaxis
## official -> sixad drivers, support official and gasia sisaxis
## shanwan -> shanwan drivers, support official and shanwan sisaxis
controllers.ps3.driver=bluez
 
# ------------ D2 - GPIO Controllers ------------ #
## GPIO Controllers
## enable controllers on GPIO with mk_arcarde_joystick_rpi (0,1)
controllers.gpio.enabled=0
## mk_gpio arguments, map=1 for one controller, map=1,2 for 2 (map=1,map=1,2)
controllers.gpio.args=map=1,2
## Custom mk_gpio arguments,
## map=5 gpio1=Y-,Y+,X-,X+,start,select,a,b,tr,y,x,tl,hk  for one controller,
## map=5 gpio1=pin1,pin2,pin3,.....,pin12,pin13
## map=5,6 gpio1=Y-,Y+,X-,X+,start,select,a,b,tr,y,x,tl,hk gpio2=Y-,Y+,X-,X+,start,select,a,b,tr,y,x,tl,hk for 2 (map=5,map=5,6)
## map=5,6 gpio1=gpiox,gpioy,gpioz,.....,gpiou,gpiov gpio2=gpiox,gpioy,gpioz,.....,gpiou,gpiov
# where gpiox,gpioy,gpioz ... are NOT pin numbers on the connector, BUT location gpio numbered as in 
# https://www.raspberrypi-spy.co.uk/wp-content/uploads/2012/06/Raspberry-Pi-GPIO-Layout-Model-B-Plus-rotated-2700x900.png
## Set pin to -1 to disable it
# controllers.gpio.args=map=5,6 gpio=4,17,27,22,10,9,25,24,23,18,15,14,2 gpio2=11,5,6,13,19,26,21,20,16,12,7,8,3
## MCP configuration : GPIO and MCP can be used together. You can mix them.
## map=0x20,0x21 for 2 mcp23017 on i2c bus
#controllers.gpio.args=map=0x20,0x21,5,6 gpio=4,17,27,22,10,9,25,24,23,18,15,14,-1 gpio2=11,5,6,13,19,26,21,20,16,12,7,8,-1
 
# ------------ D3 - Steam Controllers ------------ #
## Enable steam controller service
controllers.steam.enabled=0
 
## DB9 Controllers
## Enable DB9 drivers for atari, megadrive, amiga controllers (0,1)
controllers.db9.enabled=0
## db9 arguments
controllers.db9.args=map=1
## Gamecon controllers
## Enable gamecon controllers, for nes, snes, psx (0,1) 
controllers.gamecon.enabled=0
## gamecon_args
controllers.gamecon.args=map=1
## XGaming's XArcade Tankstik and other compatible devices
controllers.xarcade.enabled=1
 
 
# ------------ F - Language and keyboard ------------ #
## Set the language of the system (fr_FR,en_US,en_GB,de_DE,pt_BR,es_ES,it_IT,eu_ES,tr_TR,zh_CN)
system.language=fr_FR
## set the keyboard layout (fr,en,de,us,es)
system.kblayout=fr
## Set you local time
## Select your timezone from : ls /usr/share/zoneinfo/ (string)
;system.timezone=Europe/Paris
 
 
# ------------ G - UPDATES ------------ #
## Automatically check for updates at start (0,1)
updates.enabled=1
# Update type : default to stable
updates.type=stable
 
# ------------ H - HERE IT IS - GLOBAL EMULATOR CONFIGURATION ------------ #
## The global value will be used for all emulators, except if the value
## is redefined in the emulator
## Set game resolution for emulators
## select your mode from the command : tvservice -m [MODE]
## CEA 5 HDMI : 1920x1080 @ 60Hz 16:9, clock:74MHz interlaced 
## CEA 4 HDMI : 1280x720 @ 60Hz 16:9, clock:74MHz progressive
## use 'default' for using the default resolution
## use 'auto' : switches to CEA 4 HDMI if supported, else keep the current resolution
## (string)
global.videomode=CEA 4 HDMI
## Shader set 
## Automatically select shaders for all systems
## (none, retro, scanlines)
global.shaderset=none
## Once enabled, your screen will be cropped, and you will have a pixel perfect image (0,1)
global.integerscale=0
## Set gpslp shader for all emulators (prefer shadersets above). Absolute path (string)
global.shaders=
## Set ratio for all emulators (auto,4/3,16/9,16/10,custom)
global.ratio=auto
## Set smooth for all emulators (0,1)
global.smooth=0
## Set rewind for all emulators (0,1)
global.rewind=0
## Set autosave/load savestate for all emulators (0,1)
global.autosave=0
## Enable retroarchievements (0,1)
## Set your www.retroachievements.org username/password
## Escape your special chars (# ; $) with a backslash : $ => \$
global.retroachievements=0
global.retroachievements.hardcore=0
global.retroachievements.username=
global.retroachievements.password=
## Set retroarch input driver (auto, udev, sdl2)
## If you don't have issues with your controllers, let auto
global.inputdriver=auto
## If you do not want recalboxOS to generate the configuration for all emulators (string)
;global.configfile=/path/to/my/configfile.cfg
## Demo screensaver parameters
## Set the system list from which ES will run random games
global.demo.systemlist=3do,amigacd32,atari2600,atari5200,atari7800,daphne,fba_libretro,fds,gamegear,gba,lynx,mame,mastersystem,megadrive,neogeo,nes,ngpc,o2em,pcengine,sega32x,sg1000,snes
## Default demo game sessions last 90s. Change this value if you want shorter or longer sessions
;global.demo.duration=90
# ------------ I - EMULATORS CHOICES ----------- #
## You can override the global configurations here
## Here is the snes example
;snes.videomode=CEA 4 HDMI
snes.core=snes9x2002
;snes.shaders=/recalbox/share/shaders/shaders_glsl/mysnesshader.gplsp
;snes.ratio=16/9
;snes.smooth=0
;snes.rewind=1
;snes.autosave=0
;snes.emulator=libretro
;snes.integerscale=0
## If you do not want recalboxOS to generate the configuration for the emulator: 
;snes.configfile=/path/to/my/configfile.cfg
## Default cores for RPi1
snes.core=snes9x2002
gba.core=gpsp
mame.core=mame2000
nes.core=fceumm
## NeoGeo emulator 
## You can use pifba or a libretro core (fba2x,libretro)
neogeo.emulator=fba2x
## If you set libretro as neogeo.emulator, uncomment the line below and set the retroarch core (fbalpha, mame2000)
;neogeo.core=fbalpha
## Demo screensaver parameters
## Include or exclude a particular system from the demo screensaver
## You may change the global.demo.systemlist key or include/exclude every single system
;snes.demo.include=0
## Set the session duration for a particular system
;snes.demo.duration=90
# ------------ J - NETPLAY PARAMETERS ----------- #
## All these values are handled by Recalbox itself
global.netplay=1
global.netplay.nickname=
global.netplay.port=55435
global.netplay.relay=
global.netplay.systems=fba_libretro,mame,mastersystem,megadrive,neogeo,nes,pcengine,sega32x,sg1000,snes,supergrafx
global.netplay.lobby=http://lobby.libretro.com/list/
## Configurations generated by Recalbox

EDIT Modo : l'ajout de "```" avant et après un un block permet une meilleurs lisibilité

Mikaeru · 14 Apr 2019, 15:10

Mon problème ce précise j'ai remarqué aussi que sur l’écran non seulement c'est ralenti mais au lancement d'une rom j'ai une image brouillé comme un plantage (il n'y plus de son et une image blanche). En HDMI aucun souci on vois même que les émulateurs sont optimisé car je trouve le tout plus fluide qu'avant.

Pour le réglage de mon écran j'ai toujours suivi ce tuto
https://forum.recalbox.com/topic/8678/tuto-installing-recalbox-on-the-8-b-craft-raspiboy

Mikaeru · 14 Apr 2019, 17:17

J'ai observé le monitoring de la rapsberry et le cœur du processeur saturé a 100% c'est une information supplémentaire mais dont je ne trouve pas l'origine

MicMey · 14 Apr 2019, 22:02

Idem que @Gia tout tourne au ralenti

Gia · 15 Apr 2019, 00:03

@marcus_972 said in Tout Recalbox 6.0 au ralenti en composite.:

Salut,

@Gia et @Mikaeru, envoyez moi vos config.txt et recalbox.conf afin que je puisse faire des tests sur mon installation. Je passe par une péritel en RGB, je peux peut être réussir à reproduire le même bug.

Encore Merci Marcus pour ton implication.
Voici un lien de mes deux fichiers:

https://drive.google.com/drive/folders/19Z0KL03ZsLDubqrwMI2a1oiQ9Wb8Oy-u?usp=sharing

J'ai passer tout mon dimanche dessus, je pense avoir tout essayer en ce qui concerne le reclabox.conf et config.txt, je commence a avoir le sentiment que la solution n'est pas a la porter de ces deux fichiers malheureusement.

Gia · 15 Apr 2019, 09:45

@micmey said in Tout Recalbox 6.0 au ralenti en composite.:

Idem que @Gia tout tourne au ralenti

Le ralentissement global de la recalbox est apparemment systématique pour celui qui utilise la sortie composite d'origine du Pi comme nous.
J'ai un contact brésilien sur facebook qui est dans le même cas.

Je ne sais pas s'il y a un lien mais nous avons tout les 3 un RPI3 Model B.

Gia · 15 Apr 2019, 10:18

@mikaeru said in Tout Recalbox 6.0 au ralenti en composite.:

Dit ma machine est compliqué a démonté et je voulais savoir si le fichier config était accessible autrement que en branchant la carte Sd ? Dit est ce que tu aurais par hasard l'image de la 18.07.13 sur pi 0 ?

Désolé je n'ai pas l'image de l'avant dernière version, j'ai juste une micosd déjà flashé avec.
Sinon le fichier config est accessible sans aucun démontage via le logiciel WinSCP par exemple, il faut juste être sur le même réseau bien entendu.

Mikaeru · 15 Apr 2019, 10:38

@gia merci je passerai par winscp du coup j'y pensais même pas

ian57 · 15 Apr 2019, 11:05

@Mikaeru @marcus_972 @MicMey @Gia pourriez vous tester la variable

audio_pwm_mode=0

Pour voir

Gia · 15 Apr 2019, 11:42

@ian57

Infiniment merci, je vais pour profiter de la NeoGeo CD grâce a toi.
Hier j'ai essayer #audio_pwm_mode=2 sans succès alors j'avais zapper cette piste.

Avec audio_pwm_mode=0 tout rentre dans l'ordre, encore merci.

ian57 · 15 Apr 2019, 11:51

@Gia je pense qu avec le changement de firmware la valeur par défaut est maitenant 2 et plus zéro... Car le composite n est plus beaucoup utilisé avec l'arrivée du VGA 666 et des convertisseur HDMI VGA vers rgb.
Le ralentissement avec le mode 2 est connu depuis longtemps.
Bon jeu

Mikaeru · 15 Apr 2019, 12:54

@ian57 Merci beaucoup une ligne et le problème n'est plus, j'aurais jamais réussi sans votre aide !

MicMey · 15 Apr 2019, 16:44

Salut et merci mais ou faut'il exactement placé la ligne "audio_pwm_mode=0"

Mikaeru · 15 Apr 2019, 16:53

@micmey je l'ai ajouté a la fin de config.txt et du coup tout roule et effectivement la version 6 est terriblement plus fiable et rapide

MicMey · 15 Apr 2019, 16:58

Salut et merci ca fonctionne
@Gia qu'a tu exactement comme câble? moi j'utilise un composite ce câble pour le Recalbox officiel mais ca pique aux yeux !

ian57 · 16 Apr 2019, 07:04

@micmey ah ah ah point de salut avec le composite... ça pique les yeux... moi je vous conseille rgbPi http://www.rgb-pi.com/ pi encore de vous faire un cable vga-peritel en rgb pour mettre au bout de votre convertisseur hdmi-vga...

avec ça c'est nickel

nayok · 16 Apr 2019, 11:45

MicMey · 16 Apr 2019, 15:21

@ian57 J'ai le câble RGB-PI et j'en suis très content, mais il ne fonctionne qu'avec une ancienne version de Recalbox modifié pour justement pouvoir fonctionné avec ce câble., Mais depuis quelques mois il n'y a plus eu de mise à jour chez eux, mais c'est sur qu'entre le composite et le RGB y'a pas photo.

Solved Tout Recalbox 6.0 au ralenti en composite.

Want to support us ?

87
Online

97.8k
Users

28.0k
Topics

186.8k
Posts

	# uncomment if you get no picture on HDMI for a default "safe" mode
	#hdmi_safe=1

	#disable_overscan=1

	# uncomment to force a specific HDMI mode (this will force VGA)
	#hdmi_group=1
	#hdmi_mode=1

	# comment to get jack audio
	#hdmi_drive=2

	# Using /etc/modules is deprecated and no longer supported on 4.4 kernel
	# So manually enable audio
	dtparam=audio=on

	#config_hdmi_boost=0

	# force hdmi while the tv can take time before sending the signal on the hdmi output
	#hdmi_force_hotplug=1

	# uncomment for composite PAL
	#sdtv_mode=2

	# uncomment for lirc-rpi
	#dtoverlay=lirc-rpi

	# if you plug your tv at the same time as your rpi and that the rpi switches from the hdmi or give a low resolution because tv had no enough time to initialize it
	#boot_delay=3

	# uncomment if you don't want the rainbow at startup
	#disable_splash=1

	# default CEC name
	cec_osd_name=recalbox

	# Overclock
	gpu_mem_256=128
	gpu_mem_512=256
	gpu_mem_1024=512

	avoid_safe_mode=1

	kernel=zImage

	# Raspyboy
	dtoverlay=pwm-2chan,pin=18,func=2,pin2=13,func2=4
	overscan_left=-6
	overscan_right=-6
	overscan_top=-15
	overscan_bottom=-15
	framebuffer_width=320
	framebuffer_height=240

	# Raise the first security limit up to 70° instead of 60°
	temp_soft_limit=70
	arm_freq=950
	core_freq=250
	sdram_freq=450
	force_turbo=0
	over_voltage=6
	over_voltage_sdram_p=0
	over_voltage_sdram_i=0
	over_voltage_sdram_c=0
	gpu_freq=250
	sdram_schmoo=0x02000020

	# System Variable
	# You can configure your recalbox from here
	# To set a variable, remove the first ; on the line



	# ------------ A - System Options ----------- #
	# Uncomment the system.power.switch you use
	;system.power.switch=ATX_RASPI_R2_6 # http://lowpowerlab.com/atxraspi/#installation
	;system.power.switch=MAUSBERRY # http://mausberry-circuits.myshopify.com/pages/setup
	;system.power.switch=REMOTEPIBOARD_2003 # http://www.msldigital.com/pages/support-for-remotepi-board-2013
	;system.power.switch=REMOTEPIBOARD_2005 # http://www.msldigital.com/pages/support-for-remotepi-board-plus-2015
	;system.power.switch=WITTYPI # http://www.uugear.com/witty-pi-realtime-clock-power-management-for-raspberry-pi
	;system.power.switch=PIN56ONOFF # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)
	;system.power.switch=PIN56PUSH # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)
	;system.power.switch=PIN356ONOFFRESET # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)
	;system.power.switch=PIN356PUSHRESET # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)

	## fbcp FrameBuffer Copy Program
	## For small TFT screen on GPIO and SPI
	## See https://github.com/recalbox/recalbox-os/wiki/Utility---Use-of-fbcp-for-small-TFT-screen-%28EN%29 for details
	## Needed for Waveshare 3.2" 3.5" TFT screen, 2.8" Adafruit screen
	## See https://github.com/recalbox/recalbox-os/wiki/TFT-Screen-SPI-Bus-%28EN%29
	## for support and configuration details needed by /boot/config.txt
	system.fbcp.enabled=0

	## Splash screen duration
	## 0: Video will be played for 20 seconds (default)
	## -1: All the video will be played (it won't be stopped automatically)
	## >0 : Time before the video will be stopped (in seconds)
	system.splash.length=0

	## Recalbox Manager (http manager)
	system.manager.enabled=1
	## 1 or 2, depending on the manager version you wish
	system.manager.version=2

	## Recalbox security
	# enforce security
	# samba password required
	# disable virtual gamepads
	system.security.enabled=0

	## Recalbox API (REST)
	system.api.enabled=0

	## Allow a specific resolution for ES only from the command : tvservice -m [MODE]
	## Leave commented for the default usual behaviour
	;system.es.videomode=CEA 4 HDMI

	## EmulationStation
	### menu style
	### default -> default all options menu
	### none -> no menu except the game search menu
	### bartop -> less menu, only needed for bartops
	emulationstation.menu=default
	### Select a system to show on boot (use rom directory name) (string)
	emulationstation.selectedsystem=favorites
	### Show the gamelist of the first or selected system on boot (0,1)
	emulationstation.bootongamelist=0
	### Disable system view. ES will boot and show ONLY the first or selected system (0,1)
	emulationstation.hidesystemview=0
	### Pa&ast;&ast;e Gamelists only. Show only games listed in gamelist.xml files (0,1)
	emulationstation.gamelistonly=0
	### Force basicgameList view to be displayed, even if your game systems are scraped (0,1)
	emulationstation.forcebasicgamelistview=0

	## Emulator special keys
	## default -> default all special keys
	## nomenu -> cannot popup the emulator menu
	## none -> no special keys in emulators
	system.emulators.specialkeys=default

	## Show or hide kodi in emulationstation (0,1)
	kodi.enabled=1
	## Start kodi at launch (0,1)
	kodi.atstartup=0
	## set x button shortcut (0,1)
	kodi.xbutton=1

	## Allow a specific resolution for Kodi only from the command : tvservice -m [MODE]
	## By default is using the default resolution of your screen
	kodi.videomode=default

	## Kodi can wait for a network component before starting
	## waithost is the ip or hostname that must answer to a ping to validate the availability
	## waittime is the maximum time waited when kodi boots
	## if waitmode is required, kodi will not start if the component is not available
	## if waitmode is wish, kodi will start if the component is not available
	## if waitmode is not set or has another value, kodi will start immediately
	;kodi.network.waitmode=required
	;kodi.network.waittime=10
	;kodi.network.waithost=192.168.0.50

	## Hyperion
	## Hyperion allows you to use an ambilight like led system on your recalbox
	## Use hypercon to create your configuration file, and copy it in /recalbox/share/system/configs/hyperion/hyperion.config.json
	hyperion.enabled=0


	# ------------ B - Network ------------ #
	## Set system hostname
	system.hostname=RASPIBOY
	## Activate wifi (0,1)
	wifi.enabled=1
	## Set wifi region
	## More info here: https://github.com/recalbox/recalbox-os/wiki/Wifi-country-code
	wifi.region=US
	## Wifi SSID (string)
	wifi.ssid=SosoMike
	## Wifi KEY (string)
	## after rebooting the recalbox, the "new key" is replace by a hidden value "enc:xxxxx"
	## you can edit the "enc:xxxxx" value to replace by a clear value, it will be updated again at the following reboot
	## Escape your special chars (# ; $) with a backslash : $ => \$
	wifi.key=enc:U2FsdGVkX1/ie4wOQL7Q17zvzz8pdPweQjzqHjYtlPQ=

	## Wifi - static IP
	## if you want a static IP address, you must set all 3 values (ip, gateway, and netmask)
	## if any value is missing or all lines are commented out, it will fall back to the
	## default of DHCP
	;wifi.ip=manual ip address
	;wifi.gateway=new gateway
	;wifi.netmask=new netmask

	# secondary wifi (not configurable via the user interface)
	;wifi2.ssid=new ssid
	;wifi2.key=new key
	# defaults to dhcp. uncomment for static ip
	;wifi2.ip=manual ip address
	;wifi2.gateway=new gateway
	;wifi2.netmask=new netmask

	# third wifi (not configurable via the user interface)
	;wifi3.ssid=new ssid
	;wifi3.key=new key
	# defaults to dhcp. uncomment for static ip
	;wifi3.ip=manual ip address
	;wifi3.gateway=new gateway
	;wifi3.netmask=new netmask

	## Samba share
	system.samba.enabled=1
	### Virtual Gamepads
	system.virtual-gamepads.enabled=1
	### SSH
	system.ssh.enabled=1

	# ------------ C - Audio ------------ #
	## Set the audio device (auto, hdmi, jack)
	audio.device=auto
	## Set system volume (0..100)
	audio.volume=90
	## Enable or disable system sounds in ES (0,1)
	audio.bgmusic=1



	# -------------- D - Controllers ----------------- #
	# Enable support for standard bluetooth controllers
	controllers.bluetooth.enabled=1


	## Please enable only one of these
	# -------------- D1 - PS3 Controllers ------------ #
	##Enable PS3 controllers support
	controllers.ps3.enabled=1
	## Choose a driver between bluez, official and shanwan
	## bluez -> bluez 5 + kernel drivers, support official and shanwan sisaxis
	## official -> sixad drivers, support official and gasia sisaxis
	## shanwan -> shanwan drivers, support official and shanwan sisaxis
	controllers.ps3.driver=bluez


	# ------------ D2 - GPIO Controllers ------------ #
	## GPIO Controllers
	## enable controllers on GPIO with mk_arcarde_joystick_rpi (0,1)
	controllers.gpio.enabled=0
	## mk_gpio arguments, map=1 for one controller, map=1,2 for 2 (map=1,map=1,2)
	controllers.gpio.args=map=1,2
	## Custom mk_gpio arguments,
	## map=5 gpio1=Y-,Y+,X-,X+,start,select,a,b,tr,y,x,tl,hk for one controller,
	## map=5 gpio1=pin1,pin2,pin3,.....,pin12,pin13
	## map=5,6 gpio1=Y-,Y+,X-,X+,start,select,a,b,tr,y,x,tl,hk gpio2=Y-,Y+,X-,X+,start,select,a,b,tr,y,x,tl,hk for 2 (map=5,map=5,6)
	## map=5,6 gpio1=gpiox,gpioy,gpioz,.....,gpiou,gpiov gpio2=gpiox,gpioy,gpioz,.....,gpiou,gpiov
	# where gpiox,gpioy,gpioz ... are NOT pin numbers on the connector, BUT location gpio numbered as in
	# https://www.raspberrypi-spy.co.uk/wp-content/uploads/2012/06/Raspberry-Pi-GPIO-Layout-Model-B-Plus-rotated-2700x900.png
	## Set pin to -1 to disable it
	# controllers.gpio.args=map=5,6 gpio=4,17,27,22,10,9,25,24,23,18,15,14,2 gpio2=11,5,6,13,19,26,21,20,16,12,7,8,3
	## MCP configuration : GPIO and MCP can be used together. You can mix them.
	## map=0x20,0x21 for 2 mcp23017 on i2c bus
	#controllers.gpio.args=map=0x20,0x21,5,6 gpio=4,17,27,22,10,9,25,24,23,18,15,14,-1 gpio2=11,5,6,13,19,26,21,20,16,12,7,8,-1


	# ------------ D3 - Steam Controllers ------------ #
	## Enable steam controller service
	controllers.steam.enabled=0


	## DB9 Controllers
	## Enable DB9 drivers for atari, megadrive, amiga controllers (0,1)
	controllers.db9.enabled=0
	## db9 arguments
	controllers.db9.args=map=1

	## Gamecon controllers
	## Enable gamecon controllers, for nes, snes, psx (0,1)
	controllers.gamecon.enabled=0
	## gamecon_args
	controllers.gamecon.args=map=1

	## XGaming's XArcade Tankstik and other compatible devices
	controllers.xarcade.enabled=1



	# ------------ F - Language and keyboard ------------ #
	## Set the language of the system (fr_FR,en_US,en_GB,de_DE,pt_BR,es_ES,it_IT,eu_ES,tr_TR,zh_CN)
	system.language=fr_FR
	## set the keyboard layout (fr,en,de,us,es)
	system.kblayout=fr
	## Set you local time
	## Select your timezone from : ls /usr/share/zoneinfo/ (string)
	;system.timezone=Europe/Paris



	# ------------ G - UPDATES ------------ #
	## Automatically check for updates at start (0,1)
	updates.enabled=1
	# Update type : default to stable
	updates.type=stable


	# ------------ H - HERE IT IS - GLOBAL EMULATOR CONFIGURATION ------------ #
	## The global value will be used for all emulators, except if the value
	## is redefined in the emulator

	## Set game resolution for emulators
	## select your mode from the command : tvservice -m [MODE]
	## CEA 5 HDMI : 1920x1080 @ 60Hz 16:9, clock:74MHz interlaced
	## CEA 4 HDMI : 1280x720 @ 60Hz 16:9, clock:74MHz progressive
	## use 'default' for using the default resolution
	## use 'auto' : switches to CEA 4 HDMI if supported, else keep the current resolution
	## (string)
	global.videomode=CEA 4 HDMI

	## Shader set
	## Automatically select shaders for all systems
	## (none, retro, scanlines)
	global.shaderset=none

	## Once enabled, your screen will be cropped, and you will have a pixel perfect image (0,1)
	global.integerscale=0

	## Set gpslp shader for all emulators (prefer shadersets above). Absolute path (string)
	global.shaders=

	## Set ratio for all emulators (auto,4/3,16/9,16/10,custom)
	global.ratio=auto

	## Set smooth for all emulators (0,1)
	global.smooth=0

	## Set rewind for all emulators (0,1)
	global.rewind=0

	## Set autosave/load savestate for all emulators (0,1)
	global.autosave=0

	## Enable retroarchievements (0,1)
	## Set your www.retroachievements.org username/password
	## Escape your special chars (# ; $) with a backslash : $ => \$
	global.retroachievements=0
	global.retroachievements.hardcore=0
	global.retroachievements.username=
	global.retroachievements.password=

	## Set retroarch input driver (auto, udev, sdl2)
	## If you don't have issues with your controllers, let auto
	global.inputdriver=auto

	## If you do not want recalboxOS to generate the configuration for all emulators (string)
	;global.configfile=/path/to/my/configfile.cfg

	## Demo screensaver parameters
	## Set the system list from which ES will run random games
	global.demo.systemlist=3do,amigacd32,atari2600,atari5200,atari7800,daphne,fba_libretro,fds,gamegear,gba,lynx,mame,mastersystem,megadrive,neogeo,nes,ngpc,o2em,pcengine,sega32x,sg1000,snes
	## Default demo game sessions last 90s. Change this value if you want shorter or longer sessions
	;global.demo.duration=90

	# ------------ I - EMULATORS CHOICES ----------- #
	## You can override the global configurations here
	## Here is the snes example
	;snes.videomode=CEA 4 HDMI
	snes.core=snes9x2002
	;snes.shaders=/recalbox/share/shaders/shaders_glsl/mysnesshader.gplsp
	;snes.ratio=16/9
	;snes.smooth=0
	;snes.rewind=1
	;snes.autosave=0
	;snes.emulator=libretro
	;snes.integerscale=0
	## If you do not want recalboxOS to generate the configuration for the emulator:
	;snes.configfile=/path/to/my/configfile.cfg

	## Default cores for RPi1
	snes.core=snes9x2002
	gba.core=gpsp
	mame.core=mame2000
	nes.core=fceumm

	## NeoGeo emulator
	## You can use pifba or a libretro core (fba2x,libretro)
	neogeo.emulator=fba2x
	## If you set libretro as neogeo.emulator, uncomment the line below and set the retroarch core (fbalpha, mame2000)
	;neogeo.core=fbalpha

	## Demo screensaver parameters
	## Include or exclude a particular system from the demo screensaver
	## You may change the global.demo.systemlist key or include/exclude every single system
	;snes.demo.include=0
	## Set the session duration for a particular system
	;snes.demo.duration=90

	# ------------ J - NETPLAY PARAMETERS ----------- #
	## All these values are handled by Recalbox itself
	global.netplay=1
	global.netplay.nickname=
	global.netplay.port=55435
	global.netplay.relay=
	global.netplay.systems=fba_libretro,mame,mastersystem,megadrive,neogeo,nes,pcengine,sega32x,sg1000,snes,supergrafx
	global.netplay.lobby=http://lobby.libretro.com/list/

	## Configurations generated by Recalbox

Solved Tout Recalbox 6.0 au ralenti en composite.

Want to support us ?

87Online

97.8kUsers

28.0kTopics

186.8kPosts

87
Online

97.8k
Users

28.0k
Topics

186.8k
Posts