Nespi Case+/ safe shutdown installed / power and reset buttons not working at all

[yeeshkul]

I do need to install the script. The Nespi Case+ page sais so.
See the link
http://download.retroflag.com/

[Scavy]

@yeeshkul hi
Go in your recalbox.conf file, open it using notepad++, check the required line :

# System Variable
# You can configure your recalbox from here
# To set a variable, remove the first ; on the line

# ------------ A - System Options ----------- #
#    Uncomment the system.power.switch you use
;system.power.switch=ATX_RASPI_R2_6      # http://lowpowerlab.com/atxraspi/#installation
;system.power.switch=MAUSBERRY           # http://mausberry-circuits.myshopify.com/pages/setup
;system.power.switch=REMOTEPIBOARD_2003  # http://www.msldigital.com/pages/support-for-remotepi-board-2013
;system.power.switch=REMOTEPIBOARD_2005  # http://www.msldigital.com/pages/support-for-remotepi-board-plus-2015
;system.power.switch=WITTYPI             # http://www.uugear.com/witty-pi-realtime-clock-power-management-for-raspberry-pi
;system.power.switch=PIN56ONOFF          # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)
;system.power.switch=PIN56PUSH           # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)
;system.power.switch=PIN356ONOFFRESET    # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)
;system.power.switch=PIN356PUSHRESET     # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)

line 14 : simply remove the ";" in front on the pin356ONOFFRESET

Save your file, and that's all.

Don't forget recalbox is an operating system !

[paradadf]

@yeeshkul I really don't understand this kind of attitude. You already tried it and it didn't work as expected. You get new instructions and you don't want to believe it.

[yeeshkul]

@paradadf I did try without the script and it didn't work. Both buttons were completely irresponsive. I installed the script - which installed well - and there was no change.

Why would i believe something that is not even explained, when the RetroFlag company itself directs people to install the script.

[yeeshkul]

@Scavy Thank you, i will try this

[paradadf]

@yeeshkul I gave you the same instructions as scavy.
And you are in recalbox forum... so you better believe what recalbox people tell you or you should ask retroflag directly.

[yeeshkul]

@paradadf I see, i am sorry, i must have missread your post. Thank you

[antoni]

My personal recommendation is to use this version of the script, to use the reset button to reset game/exit emulator/restart emulation station.

https://github.com/crcerror/retroflag-picase

Quick Press on Game, will reset the game only
Long Press on Game, will quit the emulator

""
Multi Switch Shutdown

with advanced shutdown features for more natural behaviour:

If you press restart if emulator is currently running, then you will be kicked back to ES main menu
If you press restart in ES main screen, ES will be restartet (no reboot!), good for quick saving metadata or internal saves.
If you press power-off then Raspberry will shutdown

All metadata is always saved
""

[asturur]

@antoni Does this script require to unflag the corresponding line in the recalbox config too? or we add the script only?

What i m looking for is a script that can shut down the fan of the nespi4 when it turns off the raspberry. The fan never goes off.

[antoni]

@asturur

Follow the instructions on this page, be sure that you enable the internal <Safe Shutdown> switch.
https://github.com/crcerror/retroflag-picase

Can you try to run this on your recalbox

wget -O - "https://raw.githubusercontent.com/crcerror/retroflag-picase/master/install_recalbox.sh" | bash

it must install the following files:

/opt/RetroFlag/recalbox_SafeShutdown.py
/opt/RetroFlag/recalbox_SafeShutdown.sh

/etc/init.d/S99RetroFlag check for the following line

python /opt/RetroFlag/recalbox_SafeShutdown.sh &

/boot/config check for the following lines

enable_uart=1
# Overlay setup for proper powercut, needed for Retroflag cases
dtoverlay=gpio-poweroff,gpiopin=4,active_low=1,input=1