Solved a few beginner problems?

[Substring]

@heiner what you're supposed to do is :

1. start your pi and wait until it reaches ES
2. plug your USB cable. The controller may rumble after approx 10s
3. once it was rumbling, unplus it, press the home key, and wait. Don't rely on the leds, they may keep blinking. Just try to move in ES, or reconfigure your pad. If you don't have any other controller, make sure your pi was plugged to network at boot, and go to http://recalbox/ and start the virtual pad. Press start, go to controllers options, map the pad

[heiner]

Hello,

Now I have a BT Dongle from the compatibility list (CSL Nano) but still the same problem.

1. I start the PI until ES is fully loaded
2. I plug in my controller with USB
3. after some time it starts vibrating
   3a. if I now press the home button the blinking four LEDs turn to permanent two LEDs
   3b. If I plug it off first and then press the home button nothing happens.

[acris]

Hello
check is shanwan with dmesg command line : https://github.com/recalbox/recalbox-os/wiki/PS3-controllers-drivers-(EN)

you need to edit recalbox.conf to use good driver.
this line : controllers.ps3.driver=official

https://github.com/recalbox/recalbox-os/wiki/recalbox.conf-(EN)

[heiner]

dmesg output:
29.493578] usb 1-1.3: Product: PS(R) Ga`epad
[ 29.493585] usb 1-1.3: Manufacturer: ShanWan
[ 30.068682] cfg80211: Calling CRDA to update world regulatory domain
[ 33.228691] cfg80211: Calling CRDA to update world regulatory domain
[ 36.388645] cfg80211: Calling CRDA to update world regulatory domain
[ 39.548665] cfg80211: Calling CRDA to update world regulatory domain
[ 42.708690] cfg80211: Calling CRDA to update world regulatory domain
[ 45.868660] cfg80211: Calling CRDA to update world regulatory domain
[ 49.028695] cfg80211: Exceeded CRDA call max attempts. Not calling CRDA
[ 102.889873] usb 1-1.3: USB disconnect, device number 6

[heiner]

this comes after that

[ 573.564112] input: ShanWan PS(R) Gaepad as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.3/1-1.3:1.0/0003:054C:0268.0007/input/input5 [ 573.565461] sony 0003:054C:0268.0007: input,hiddev0,hidraw1: USB HID v1.10 Joystick [ShanWan PS(R) Gaepad] on usb-3f980000.usb-1.3/input0
[ 573.565585] sony 0003:054C:0268.0007: can't set operational mode: step 1
[ 573.642813] sony: probe of 0003:054C:0268.0007 failed with error -32
[ 573.736600] usb 1-1.3: USB disconnect, device number 11

[heiner]

I found a thread where some people had similar problems and they seem to solve it with a patched version of bluez:
https://retropie.org.uk/forum/topic/42/shanwan-ps3-controller-pi3-retropie-3-6-bluetooth-setup/126

it seems that you need a forked version of bluez:
https://github.com/luetzel/bluez

more details on: https://luetzels.raspiblog.com/?p=1870

Maybe someone from the devs can fix the problem with this information?

[Substring]

hey

this is how things are supposed to work :

1. plug your shanwan with the usb cable.it should rumble after 10s. That is to set the master BT address for the pad. you can check the log in /recalbos/share/system/logs/controllers.log. If there is no (new) entry, then sthg is wrong
2. next unplug the cable and press PS. After about 10s yourpad should be paired (despite shanwans may keep blinking). Once paired there is a log in /var/log/messages for the sixbin or six??? daemon. You should also have a new entry in dmesg

could you try 'hciconfig hci0'and show me its output ?

the retropie link can't be used for recalbox 4.0, and I'm working on the recalbox way to implement bluez5

[heiner]

hciconfig hci0

hci0: Type: BR/EDR Bus: USB
BD Address: 00:1A:7D:DA:71:15 ACL MTU: 310:10 SCO MTU: 64:8
UP RUNNING PSCAN
RX bytes:51027 acl:939 sco:0 events:1904 errors:0
TX bytes:24258 acl:940 sco:0 commands:367 errors:0

[heiner]

this is in controllers.log
after first plug in
the controller is not rumbling:

Current Bluetooth master: 00:00:00:00:00:00 
Setting master bd_addr to 00:1a:7d:da:71:15 

if I plug out and plug in again it starts to rumble:

dmesg output:
https://thepb.in/p/qjhLgOpQp55cB

after second plugin the controllers.log looks like this:
https://thepb.in/p/lOhOWoBG0xmUB

new dmesg output:
https://thepb.in/p/BghPxVgOB5WIY

and out put to /var/messages:
https://thepb.in/p/qjhLgOpAm0WUB

these lines seems to be suspicious:

Sep  9 19:52:01 RECALBOX daemon.info bluetoothd[299]: Terminating 
Sep  9 19:52:01 RECALBOX daemon.info bluetoothd[299]: Stopping SDP server 
Sep  9 19:52:01 RECALBOX daemon.info bluetoothd[299]: Exit 

bluetoothd is terminating

[heiner]

I FOUND MY PROBLEM
For one or another reason the ps3 controller support was set to 0 (!!!!)
I set it back to 1 and everything worked. I cant believe it....

[Substring]

LOOOOOOOOOOOOOOOL

glad you made it through