Buttons are pressed without touching them!!

[saver]

@substring i have this image to my sdcard https://www.youtube.com/watch?v=kklTCp8HZBo and i can t find to the menu the recalbox webmanager to edit recalbox.conf. I tried from the config text but i didn t find "controllers.gpio.enabled"
I made two arcade cabinet with the same setup and i have this problem only in one of them. Do you thing that if i disable the gpio driver i will fix it?

[Substring]

@saver i'm not doing any support for unofficial images

[saver]

@substring i am really sory but i didn t know that it was unofficial. I just made a resaearch for a recalbox image 32 gb like my sd card. I am not so familiar with all those things. I ll try with the official way. Anyway thank you very much for your help.

[OyyoDams]

@saver The official image is here: https://archive.recalbox.com/

[saver]

@oyyodams thank you very much. I hope with the ofdicial image to solve the problem.

[saver]

Hello again. I install the official recalbox image but i still have the same problem. Here is what is written to recalbox.conf. The gpio controllers are already set to 0. Do i have to put # in the beggining of the sentence?

------------ D2 - GPIO Controllers ------------

GPIO Controllers

enable controllers on GPIO with mk_arcarde_joystick_rpi (0,1)

controllers.gpio.enabled=0

mk_gpio arguments, map=1 for one controller, map=1,2 for 2 (map=1,map=1,2)

controllers.gpio.args=map=1,2

[NeeeeB]

@saver Nope, no need to comment the line, it's set to 0 so it is disabled.

[saver]

@substring can you please tell me if now there is something wrong with my setup. The only thing i haven t replaced yet is the screen. Here is my bartop cabinet ant the results of the new evtest
https://postimg.cc/gallery/16tfiq92g/31740cb1/

[Substring]

@saver can you run again evtest with device 1 instead of 0 ?

[saver]

@substring here it is.
https://postimg.cc/image/rzwpj3q3b/b80aabbe/

Now the player 2 buttons are unplugged. I try to isolate the problem but u fortunately i can t

[Substring]

@saver nothing seems to happen on your xinmo. Do you still have ghost inputs if you unplug your xinmo ?

[saver]

@substring when the problem began i had those inputs even with the xin mo unplugged. Now i haven t try it again. I have already replaced the whole xin mo set exept the buttons, the raspberry pi , the sd card and all the cables. The only thing i haven t replaced yet is the screen because i haven t a second one. But i still have the problem. And it begins after 2 or three hours or more after switching on the console and not from the beginning. I made a second bartop cabinet with the same setup for my brother with no problem at all. Mine bartop has the problem. I am so desperate!

[Substring]

@saver you have to run evtest when the problem does happen, and run evtest on ech input device

[saver]

@substring i tried yesterday to run evtest when the problem began again but i noticed that the pie was out of internret connection. Then i tried to connect to my wifi and i saw instead of my wifi key this https://postimg.cc/image/ilx9c1jkn/343a9b6e/.
I didn t touch anything. I think that if i manage to put my wifi key and connect to my wifi i will solve the problem. But temporarily. Can you think what is going on now?

[Substring]

@saver the wifi key is encrypted (hence enc:) for security purpose

[saver]

@substring so i guess this is not the broblem?

[Substring]

@saver nope. But why are you losing lan connection ?

[saver]

@substring i realy don t know. But i have the same problem even without connection at all

[saver]

@substring here is the evtes during the problem https://postimg.cc/gallery/2t129wh3w/b01e24f1/
And still is writing and writing and writing

[Dragu]

@saver
Could you post a picture about your connections INSIDE the bartop, buttons and joysticks. Mass (-) connection needs to be connected in chain from one button to the next, otherway you risk HF disturbances. Same problème for switching power supply units near the mass cables. If they have no metallic case and are from the type to put on the table near a notebook, or in socket far away, together with parallel mass wires, deadly.
Also it can just be a defect 5V power supply unit, because I read that it arrive after some time only. I would change this first. And take an 3A Aukru or Northpada