@zing
Thank you very much.
Intresting project. I will follow and build something similar.

Cheers!
Rakete

Hi there!
I would like to play PONG. I found Video Olypics but wonder wich controller to use.
Best would be a USB Paddle. But I dound only those:

https://www.amazon.com/R-STYLE-Controller-Suitable-emulators-hyperspin/dp/B07RYT7YXJ

which I think is much to expensive.
Any ideas? Maybe DIY-Project?

Also - this there any other PONG ROM?

Cheers!
Rakete

Hi there!
I cannot start XENON ROM on MAME.
I run Recalbox 7.2.2 and tried all BIOS that comes with the Recalbox installation.

So I wonder if there is any other BIOS for MAME needed.

THanks!
Raketenmann

Hooray!
Top Support.
Thank you!

It would be great if I could set the DNS in the config file or, even better, one or more DNS Servers would be preconfigured.

However - I could do a beta test imidiate if needed. Got a backup SD-Card ready to try.

Cheers
Rakete

@zing
Thanks for your quick answer. I didn't know about this article.
Unfortunately, my router does not offer the option of assigning a fixed IP.

Unless someone else has a solution, I will wait for a patch or a new version.

Thank you very much!
Rakete

Hi there!
My Recalbox cannot connect to the Internet as soon as I use static IP by using:

wifi.ip=192.168.5.235
wifi.gateway=192.168.5.1
wifi.netmask=255.255.255.0

I am pretty sure this is an DNS issue. But cannot find where to set the DNS Server.
However, by using the DHCP setting it works fine. But I would like to use a static IP.

Thanks!
Raketenmann

Thx!
First I tried to update. Did not worked.
Thats why I changed the File by using the shared folder and SSH.

Now- as it works - I will keep it until the next official release where you hopefully take care on RPi 1 users.

Again: great support.
Thx
CHristian

Thank you Gentlemen!

Works now.
Not perfect. But I received a first feedback while configure controls. Rest will be easy and fixed in the config file later today.

You may close this!
Great support.
Thanks!
Christian

Hi Ian,
it might be a stupid question. But how to copy the file?

cp: can't create '/lib/modules/4.14.62/extra/mk_arcade_joystick_rpi.ko': File exists

Sure. But if I try to delete it - even with root / su

rm: can't remove 'mk_arcade_joystick_rpi.ko': Read-only file system

BTW - Recalbox UI shows there is an update available if I switch to "BETA". But the download fails.

Thank you!
Christian

Hi IAN57,
thanks for the quick answer.
The module is loaded - it seams to me:
Module Size Used by Tainted: G
mk_arcade_joystick_rpi 4442 0

And here is the output from the evtest:
Input driver version is 1.0.1
Input device ID: bus 0x15 vendor 0x1 product 0x1 version 0x100
Input device name: "GPIO Controller 1"
Supported events:
Event type 0 (EV_SYN)
Event type 1 (EV_KEY)
Event code 304 (BTN_SOUTH)
Event code 305 (BTN_EAST)
Event code 307 (BTN_NORTH)
Event code 308 (BTN_WEST)
Event code 310 (BTN_TL)
Event code 311 (BTN_TR)
Event code 314 (BTN_SELECT)
Event code 315 (BTN_START)
Event code 316 (BTN_MODE)
Event type 3 (EV_ABS)
Event code 0 (ABS_X)
Value 0
Min -1
Max 1
Event code 1 (ABS_Y)
Value 0
Min -1
Max 1

But no reaction on any input.

RPi Version: Pi Model B Rev 2
(thats the output from cat /sys/firmware/devicetree/base/model)

Thanks!
CHristian

Hi there,

I cannot configure my (BarTop) Joystick.
see: https://github.com/recalbox/mk_arcade_joystick_rpi/blob/hotkeybtn/README.md#pinout

And here is, what I tried in my .conf file.
(of course I also tried standard config)

------------ D2 - GPIO Controllers ------------

GPIO Controllers

enable controllers on GPIO with mk_arcarde_joystick_rpi (0,1)

controllers.gpio.enabled=1

mk_gpio arguments, map=1 for one controller, map=1,2 for 2 (map=1,map=1,2)

controllers.gpio.args=map=5

Custom mk_gpio arguments,

map=5 gpio1=Y-,Y+,X-,X+,start,select,a,b,tr,y,x,tl,hk for one controller,
map=5 gpio1=pin11,pin7,pin13,pin15,pin19,pin21,pin22,pin18,pin16,pin12,pin-1,pin-1,pin3

map=5,6 gpio1=Y-,Y+,X-,X+,start,select,a,b,tr,y,x,tl,hk gpio2=Y-,Y+,X-,X+,start,select,a,b,tr,y,x,tl,hk for 2 (map=5,map=5,6)

map=5,6 gpio1=gpiox,gpioy,gpioz,.....,gpiou,gpiov gpio2=gpiox,gpioy,gpioz,.....,gpiou,gpiov

where gpiox,gpioy,gpioz ... are NOT pin numbers on the connector, BUT location gpio numbered as in

https://www.raspberrypi-spy.co.uk/wp-content/uploads/2012/06/Raspberry-Pi-GPIO-Layout-Model-B-Plus-rotated-2700x900.png

Set pin to -1 to disable it

controllers.gpio.args=map=5 gpio=11,7,13,15,19,21,22,18,16,12,-1,-1,3

MCP configuration : GPIO and MCP can be used together. You can mix them.

map=0x20,0x21 for 2 mcp23017 on i2c bus

#controllers.gpio.args=map=0x20,0x21,5,6 gpio=4,17,27,22,10,9,25,24,23,18,15,14,-1 gpio2=11,5,6,13,19,26,21,20,16,12,7,8,-1

It just doesn't work at all.
Any ideas?
Thank you!
Christian

AHA - ich glaube mittlerweile ich bin lediglich zu doof um die Syntax der
recalbox.conf
zu verstehen.
Vielleicht kann mir da einer unter die Arme greifen.

Das Board ist dieses hier:
http://arcadeforge.net/download/Installationshinweise_PiJamma.pdf

Merci!
Christian

Hallo allerseits,
bin jetzt seit 24 Stunden auf Fehlersuche und bekomme meinen Bartop nicht zum laufen. 1 Joystick und 9 Tasten an einem PiJamma Board über ein Flachbandkabel am GPIO eines Raspberry 1.
Controller Unterstützung für GPIO ist aktiviert. MAP=1.
Alles mehrfach durchgepiept.
KEINE (NULL) Reaktion. An keiner Taste.
Hat jemand noch eine Idee?

Grüße
Raketenmann