Retour 7.2.2 sur XU4

loli72 · 29 Jun 2021, 15:36

@cedric-debuiselle Donc ce n'est pas le même problème puisque tu n'as pas fais les modifs du fichier config.ini qui se trouve sur la carte SD. Et il suffit de la brancher sur ton ordi pour voir les fichiers.

manitou · 29 Jun 2021, 16:38

@loli72 le probleme c'est que je n'ai pas la version 7.1.1. Je n'avais pas téléchargé le fichier de l'époque
Donc si à tout hasard tu as encore la version d'origine afin que j'installe cette version pour essayer de voir si c'est l'ecran ou non

cedric-debuiselle · 29 Jun 2021, 18:11

@loli72 j'ai fait les les modif sur recalbox.conf et config.ini , marche pas non plus j'ai reformater ma clé USB et réinstallé recalbox aucun changement
@manitou recalbox tu l'as installé sur une micro SD ou sur un eMMC?

manitou · 30 Jun 2021, 08:20

@cedric-debuiselle pour ma part l'installation est faite sur une micro SD
Franchement dommage que cette version soit vraiment délaissée car le boitier est vraiment top (quand on arrive à le faire fonctionner) et la xu4 fait vraiment le taff....

Je regrette vraiment d'avoir effectué la migration car sur ma version 6.0 tout fonctionné parfaitement...

Je pense que maintenant, je vais acheter une seconde micro SD afin de faire toute nouvelle installation sur celle-ci afin de pouvoir tester avant d’écraser une version qui fonctionne bien car la j'ai fort l'impression que je vais me retrouver avec un boitier avec un ecran sans aucune utilité....

Je vais essayer de créer un post sur notre probleme, n’hésite pas à venir te manifester dessus

loli72 · 30 Jun 2021, 13:19

@manitou J'ai tout vérifié et avec la v7.2.2, les modifs sur les fichiers indiqués suffisent. A part que l'image est très saccadée mais il y a bien une image et des vidéo qui changent en fonction du système sélectionné.
Mais en ce qui me concerne, je ne fais jamais les mises à jours automatiques mais toujours la méthode manuelle avec Etcher ou autre et je renomme mon dossier "recalbox" en "recalboxOLD" sur mon support externe pour ne rien perdre.
Une installation propre quoi. C'est peut être ça la différence, tu aurais des fichiers de l'ancienne version mélangés à la nouvelle.

manitou · 30 Jun 2021, 14:34

@loli72 Je fais egalement comme toi
Je fais jamais les mises à jours automatiques, je passe toujours par une réinstallation complète afin d'avoir une base propre donc le probleme ne vient pas de là non plus

c'est d'ailleurs la raison pour laquelle je voulais savoir si tu avais la 7.1.1 en setup pour essayer de l'installer afin de voir si le probleme est identique

loli72 · 30 Jun 2021, 15:54

@manitou Je l'ai mais elle fait plus de 800Mo et je ne vais m'inscrire à un cloud pour ça, désolé. De toute façon j'ai le même matériel que toi. Chez moi cela fonctionne en 7.2.2 et 7.1.1 donc si ça marche pas chez toi en 7.2.2 ce sera très sûrement pareil en 7.1.1.
Tu dois avoir un problème matériel ou bien un truc tellement énorme qu'on le voit pas dans tes fichiers de conf.

manitou · 1 Jul 2021, 22:24

@loli72 il est bien la le probleme, c'est que je n'ai rien de spécifique....
Même avec une installation standard à neuf en 7.2.2 sans rien changer dans les menus ou même dans les autres fichiers que les deux en question l’écran n'affiche rien ...

Donc pour être certain le fichier en 7.1.1 m'aurait bien servi...
Il y a une solution simple et très facile même avec les fichiers volumineux. C'est le lien WeTransfer
Pourrais tu me l'envoyer via cette solution stp ?
Si tu as besoin je peux t'aider à créer le lien

loli72 · 6 Jul 2021, 22:16

@manitou Non désolé , je limite mon empreinte numérique à l'indispensable.
Cela dit je je pense que tu auras le même soucis en 7.1.1 pour les raisons citées plus haut.

manitou · 2 Jul 2021, 14:37

@loli72 merci pour ton retour.
Hélas dans le lien que tu viens de me partager il n'y a que la version 7.2.2 en fichier image
De plus, je viens de réussir à faire fonctionner l’écran avec la version 6.0 ou j'ai réussi à récupérer un script pour voir juste l'image du démarrage.
Donc je suis soulagé qu'il ne s'agisse pas d'un problème de matériel mais d'un autre coté, je suis toujours dans la même situation avec la 7.2.2 impossible de faire afficher quoi que ce soit
Tout de même étrange quand même ....

loli72 · 2 Jul 2021, 20:48

@manitou Au cas où je te laisse le contenu complet de mon recalbox.conf et du config.ini en 7.2.2. Après je vois plus quoi faire.

recalbox.conf

 # System Variable
# You can configure your recalbox from here
# To set a variable, remove the first ; on the line
# NOTE ON CEC FOR REMOTES
# you've to plug the ODROID XU4 on the HDMI1 of your tv
# this is a limitation of the EXYNOS libcec adapter
 
# ------------ A - System Options ----------- #
#    Uncomment the system.power.switch you use
;system.power.switch=ATX_RASPI_R2_6      # http://lowpowerlab.com/atxraspi/#installation
;system.power.switch=MAUSBERRY           # http://mausberry-circuits.myshopify.com/pages/setup
;system.power.switch=REMOTEPIBOARD_2003  # http://www.msldigital.com/pages/support-for-remotepi-board-2013
;system.power.switch=REMOTEPIBOARD_2005  # http://www.msldigital.com/pages/support-for-remotepi-board-plus-2015
;system.power.switch=WITTYPI             # http://www.uugear.com/witty-pi-realtime-clock-power-management-for-raspberry-pi
;system.power.switch=PIN56ONOFF          # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)
;system.power.switch=PIN56PUSH           # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)
;system.power.switch=PIN356ONOFFRESET    # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)
## Splash screen duration
##  0 : Video will be stopped when emulationstation is ready to start.
## -1 : All the video will be played before emulationstation start (default)
## >0 : Time the video will be played before emulationstation start (in seconds)
system.splash.length=-1
## Splash videos selection
## all: select a boot video in recalbox videos and user videos
## recalbox: select a boot video only in recalbox videos
## custom: select a boot video only in user videos
## Any invalid value means "all"
system.splash.select=all
## Recalbox Manager (http manager)
system.manager.enabled=1
## Currently, only version 2 is available
system.manager.version=2
## Recalbox security
# enforce security
# samba password required
# disable virtual gamepads
system.security.enabled=0
## Recalbox API (REST)
system.api.enabled=0
## EmulationStation
### menu style
### default -> default all options menu
### none -> no menu except the game search menu
### bartop -> less menu, only needed for bartops
emulationstation.menu=default
### Select a system to show on boot (use rom directory name) (string)
emulationstation.selectedsystem=favorites
### Show the gamelist of the first or selected system on boot (0,1)
emulationstation.bootongamelist=0
### Disable system view. ES will boot and show ONLY the first or selected system (0,1)
emulationstation.hidesystemview=0
### Pa&ast;&ast;e Gamelists only. Show only games listed in gamelist.xml files (0,1)
emulationstation.gamelistonly=0
### Force basicgameList view to be displayed, even if your game systems are scraped (0,1)
emulationstation.forcebasicgamelistview=0
### Filter out adult games
### you may use emulationstation.snes.filteradultgames=1
### to filter out adult games for the snes system or any other system
;emulationstation.filteradultgames=1
### Zipped gamelist preference
### Whatever you choose, emulationstation can read both compressed
### and uncompressed gamelist.xml or gamelist.zip
### However updated gamelist will be saved in your prefered format.
### Zipped format may save load time, especially on slow devices.
### 0 = gamelist.xml
### 1 = gamelist.zip
;emulationstation.zippedgamelist=1
## Arcade metasystem
## Activate the Arcade metasystem to group all games from piFBA, FBN (libretro), MAME and optionally Neogeo
## into a single "Arcade" system.
;emulationstation.arcade=1
## You may want to specify its position in the system list. (Default: 0)
## Negatives values may be used to tart from the end (-1 = last position)
;emulationstation.arcade.position=0
## Include NeoGeo or not (default: 1)
;emulationstation.arcade.includeneogeo=1
## Hide included system or leave them in the system list (default: 1)
;emulationstation.arcade.hideoriginals=1
## Virtual systems
### Activate a virtual system with all games available from all systems
;emulationstation.collection.allgames=1
### Activate a virtual system with all multiplayer games (players >= 2)
;emulationstation.collection.multiplayers=1
### Activate a virtual system with last played games
;emulationstation.collection.lastplayed=1
## Videosnaps
### Delay before videosnaps start, in millisecond. Default: 2s
;emulationstation.videosnaps.delay=2000
### Video loop times. 0 = no video. 1 or more = the video loops x times before fading out
;emulationstation.videosnaps.loop=1
### Enable videosnap sound/music
;emulationstation.videosnaps.sound=1
## Scrapers
### Activate this option to extract region from filename when possible
;scraper.extractregionfromfilename=1
### Select the source of game's names
### 0 = from scrapper result (default)
### 1 = from filename
### 2 = from filename undecorated (i.e: (text) and [text] removed)
;scraper.getnamefrom=0 
### ScreenScraper.fr
### Force media region - if not defined, region is taken from system.language. Default: us
;scraper.screenscraper.region=eu
### Force text language - if not defined, region is taken from system.language. Default: en
;scraper.screenscraper.language=fr
### Choose the media to download among:
### screenshot: game screenshot
### title     : game title screenshot
### box2d     : Front case
### box3d     : 3D rendered case
### mixv1     : Recalbox special mix image V1 (default)
### mixv2     : Recalbox special mix image V2
;scraper.screenscraper.media=mixv1
### ScreenScraper account
;scraper.screenscraper.user=
;scraper.screenscraper.password=
## Emulator special keys
## default -> default all special keys
## nomenu -> cannot popup the emulator menu
## none -> no special keys in emulators
system.emulators.specialkeys=default
## Show or hide kodi in emulationstation (0,1)
kodi.enabled=0
## Start kodi at launch (0,1)
kodi.atstartup=0
## set x button shortcut (0,1)
kodi.xbutton=0
## Kodi can wait for a network component before starting
## waithost is the ip or hostname that must answer to a ping to validate the availability
## waittime is the maximum time waited when kodi boots
## if waitmode is required, kodi will not start if the component is not available
## if waitmode is wish, kodi will start if the component is not available
## if waitmode is not set or has another value, kodi will start immediately
;kodi.network.waitmode=required
;kodi.network.waittime=10
;kodi.network.waithost=192.168.0.50
 
 
# ------------ B - Network ------------ #
## Set system hostname
system.hostname=RECALBOX
## Activate wifi (0,1)
wifi.enabled=0
## Set wifi region
## More info here: https://github.com/recalbox/recalbox-os/wiki/Wifi-country-code-(EN)
wifi.region=JP
## Wifi SSID (string)
;wifi.ssid=new ssid
## Wifi KEY (string)
## after rebooting the recalbox, the "new key" is replace by a hidden value "enc:xxxxx"
## you can edit the "enc:xxxxx" value to replace by a clear value, it will be updated again at the following reboot
## Escape your special chars (# ; $) with a backslash : $ => \$
;wifi.key=new key
## Wifi - static IP
## if you want a static IP address, you must set all 3 values (ip, gateway, and netmask)
## if any value is missing or all lines are commented out, it will fall back to the
## default of DHCP
;wifi.ip=manual ip address
;wifi.gateway=new gateway
;wifi.netmask=new netmask
# secondary wifi (not configurable via the user interface)
;wifi2.ssid=new ssid
;wifi2.key=new key
# third wifi (not configurable via the user interface)
;wifi3.ssid=new ssid
;wifi3.key=new key
## Samba share
system.samba.enabled=1
### Virtual Gamepads
system.virtual-gamepads.enabled=1
### SSH
system.ssh.enabled=1
 
 
# ------------ C - Audio ------------ #
## Set the audio device (auto, hdmi, jack)
audio.device=alsa_card.0:hdmi-output-0
## Set system volume (0..100)
audio.volume=90
## Enable or disable system sounds in ES (0,1)
audio.bgmusic=1
 
 
# -------------- D - Controllers ----------------- #
# Enable support for standard bluetooth controllers
controllers.bluetooth.enabled=1
# Enable ERTM
controllers.bluetooth.ertm=1
 
## Please enable only one of these
# -------------- D1 - PS3 Controllers ------------ #
##Enable PS3 controllers support
controllers.ps3.enabled=1
## Choose a driver between bluez, official and shanwan
## bluez -> bluez 5 + kernel drivers, support official and shanwan sisaxis
## official -> sixad drivers, support official and gasia sisaxis
## shanwan -> shanwan drivers, support official and shanwan sisaxis
controllers.ps3.driver=bluez
 
# ------------ D2 - GPIO Controllers ------------ #
## GPIO Controllers
## enable controllers on GPIO with mk_arcarde_joystick_rpi (0,1)
controllers.gpio.enabled=0
## mk_gpio arguments, map=1 for one controller, map=1,2 for 2 (map=1,map=1,2)
controllers.gpio.args=map=1,2
 
## DB9 Controllers
## Enable DB9 drivers for atari, megadrive, amiga controllers (0,1)
controllers.db9.enabled=0
## db9 arguments
controllers.db9.args=map=1
## Gamecon controllers
## Enable gamecon controllers, for nes, snes, psx (0,1) 
controllers.gamecon.enabled=0
## gamecon_args
controllers.gamecon.args=map=1
## XGaming's XArcade Tankstik and other compatible devices
controllers.xarcade.enabled=1
# ------------ D3 - Joycon Controllers ------------ #
controllers.joycond.enabled=1
 
# ------------ E - Language and keyboard ------------ #
## Set the language of the system (fr_FR,en_US,en_GB,de_DE,pt_BR,es_ES,it_IT,eu_ES,tr_TR,zh_CN)
system.language=fr_FR
## set the keyboard layout (fr,en,de,us,es)
system.kblayout=fr
## Set you local time
## Select your timezone from : ls /usr/share/zoneinfo/ (string)
;system.timezone=Europe/Paris
 
 
# ------------ F - UPDATES ------------ #
## Automatically check for updates at start (0,1)
updates.enabled=1
# Update type : default to stable
updates.type=stable
 
 
# ------------ G - HERE IT IS - GLOBAL EMULATOR CONFIGURATION ------------ #
## The global value will be used for all emulators, except if the value
## is redefined in the emulator
## Set game resolution for emulators
## Please don't modify this setting
## This arch does not support the video mode switch
## (string)
global.videomode=default
## Shader set 
## Automatically select shaders for all systems
## (none, retro, scanlines)
global.shaderset=none
## Once enabled, your screen will be cropped, and you will have a pixel perfect image (0,1)
global.integerscale=0
## Set gpslp shader for all emulators (prefer shadersets above). Absolute path (string)
global.shaders=
## Set ratio for all emulators (auto,4/3,16/9,16/10,custom)
global.ratio=auto
## Set smooth for all emulators (0,1)
global.smooth=1
## Set rewind for all emulators (0,1)
global.rewind=1
## Set autosave/load savestate for all emulators (0,1)
global.autosave=0
## Enable retroarchievements (0,1)
## Set your www.retroachievements.org username/password
## Escape your special chars (# ; $) with a backslash : $ => \$
global.retroachievements=0
global.retroachievements.hardcore=0
global.retroachievements.username=
global.retroachievements.password=
## Set retroarch input driver (auto, udev, sdl2)
## If you don't have issues with your controllers, let auto
global.inputdriver=auto
## If you do not want recalboxOS to generate the configuration for all emulators (string)
;global.configfile=/path/to/my/configfile.cfg
## Demo screensaver parameters
## Set the system list from which ES will run random games
## Empty list or unexisting key means all available systems
global.demo.systemlist=3do,amigacd32,atari2600,atari5200,atari7800,daphne,fbneo,fds,gamegear,gba,lynx,mame,mastersystem,megadrive,neogeo,nes,ngpc,pcengine,sega32x,sg1000,snes
## Default demo game sessions last 90s. Change this value if you want shorter or longer sessions
;global.demo.duration=90
## Default game info screen duration lasts 6s. Change this value if you want shorter or longer info screens.
;global.demo.infoscreenduration=6
## Retroarch AI Translation service
## Comment out or set to 0 the following key if you don't want the AI service
global.translate=1
## Set the source and the target languages.
## Allowed language list: EN, ES, FR, IT, DE, JP, NL, CS, DA, SV, HR, KO, ZH_CN, ZH_TW, CA, BG, BN, EU, AZ, AR, SQ,
##                        AF, EO, ET, TL, FI, GL, KA, EL, GU, HT, IW, HI, HU, IS, ID, GA, KN, LA, LV, LT, MK, MS,
##                        MT, NO, FA, PL, PT, RO, RU, SR, SK, SL, SW, TA, TE, TH, TR, UK, UR, VI, CY, YI
## Setting the translate.from key to a specified language may speed up or give more accurate results
## If translate.to key is commented, the default value is extracted from system.language or, if system.language is
## undefined, set to auto (=EN).
global.translate.from=auto
global.translate.to=auto
## zTranslate API Key
## go to https://ztranslate.net and create an account.
## validate your account, then log in and go to the settngs page
## Look for the API Key at the bottom of the page, then uncomment the following key and paste your API Key:
;global.translate.apikey=RECALBOX
## Other translation service
## If you want to use another translation service or a custom API call, use this key to
## specify the url to call. If the key is not empty, it is used instead of zTranslation's API Key
;global.translate.url=
 
 
# ------------ H - EMULATORS CHOICES ----------- #
## You can override the global configurations here
## Here is the snes example
;snes.core=snes9x2010
;snes.shaders=/recalbox/share/shaders/shaders_glsl/mysnesshader.gplsp
;snes.ratio=16/9
;snes.smooth=0
;snes.rewind=1
;snes.autosave=0
;snes.emulator=libretro
;snes.integerscale=0
## If you do not want recalboxOS to generate the configuration for the emulator: 
;snes.configfile=/path/to/my/configfile.cfg
## Default cores for Odroid XU4
;snes.core=snes9x
n64.core=gliden64
## NeoGeo emulator 
## You can use pifba or a libretro core (fba2x,libretro)
neogeo.emulator=libretro
## If you set libretro as neogeo.emulator, the line below sets the retroarch core (fbneo, mame2000)
neogeo.core=fbneo
## Demo screensaver parameters
## Include or exclude a particular system from the demo screensaver
## You may change the global.demo.systemlist key or include/exclude every single system
;snes.demo.include=0
## Set the session duration for a particular system
;snes.demo.duration=90
 
 
# ------------ J - TFT SECONDARY SCREEN ----------- #
#Second miniTFT screen as marquee to display scrapes and videos
#Enable it with system.secondMiniTFT.enabled=1, disable with system.secondMiniTFT.enabled=0
#this configuration is REQUIRED 
system.secondminitft.enabled=1
 
#Type of mini TFT : OGST, unknown
#Most of spi tft screen are enabled thanks to overlays in /boot/config.txt in rpi and /boot/config.ini on odroidxu4
#please check the specific configuration of your screen
#Some examples are available on the page .....
# values are :
# - overlay : screen configured through overlays in /boot/config.txt or /boot/config.ini (odroidxu4/ogst)
# - default : the rest of the world
#this configuration is REQUIRED if system.secondminitft.enabled=1
system.secondminitft.type=overlay
 
#Choose the resolution of your screen
#miniTFT resolution  320x240 -> 240p, 480x320 -> 320p
#this configuration is REQUIRED if system.secondminitft.enabled=1
system.secondminitft.resolution=240p
#Scraped image aspect on tft screen : fbv display option
# options available : stretch, ignore-aspect, enlarge.
# stretch : Strech (using a simple resizing routine) the image to fit onto screen if necessary
# alpha : use the alpha channel (if applicable)
# ignore-aspect : Ignore the image aspect while resizing
# enlarge : Enlarge the image to fit the whole screen if necessary
# 1 = enabled, 0 = disabled
#this configuration is REQUIRED if system.secondminitft.enabled=1
system.secondminitft.imagestretchenabled=1
system.secondminitft.imageenlargeenabled=0
system.secondminitft.imagealphaenabled=1
system.secondminitft.imageignoreaspectenabled=1
#When activating the second TFT screen, you may want to display
#game scraped video only on the second screen. This variable
#allows you to disable scraped video playing in ES during game browsing
#system.secondminitft.disablevideoines=1 disable video playing in ES
#system.secondminitft.disablevideoines=0 enable video playing in ES
#this configuration is OPTIONAL if system.secondminitft.enabled=1
system.secondminitft.disablevideoines=1
#if the backlight of your your screen can be manage by PWM, 
#indicates the  GPIO value of your PWM control
#WiringPi and its gpio program will be used to control the backlight
#when RB goes in SLEEP mode, and when it wakes up.
#On raspberry pi, PWMs cannot be used simultaneously with Jack sound output.
#If your are using HDMI or a Audio hat you can use backlight PWM control for the second screen
#If you are using Jack output please leave commented.
#The Screen will be switch down in Sleep mode, and switch on when it wakes up.
#On OGST, only this mode is available.
#this configuration is OPTIONAL if system.secondminitft.enabled=1
;system.secondminitft.backlightcontrol=18
# system.secondminitft.usemarquee variabla allows you to display a different
# image during running game. just creat a directory named "marquees" in media
# aside videos and images and put new images with the same name as in images
# example :
#   - /recalbox/share/roms/neogeo/media/marquees/alpham2.png
#   - /recalbox/share/roms/neogeo/media/images/alpham2.png
# if set to 1, in game the marquee images will be displayed
# if set to 0, in game the scraped images will be displayed
;system.secondminitft.usemarquee=0 
#system.secondminitft.sleepenabled allows you to enable/disable
#sleep mode for the second TFT. If set to 1 sleep mode is enabled and 
#backlight of the screen will be OFF. If set to 0, sleep mode is
#disabled and the backlight of the screen will be always On
 
;system.secondminitft.sleepenabled=0
# ------------ I - NETPLAY PARAMETERS ----------- #
## All these values are handled by Recalbox itself
global.netplay=1
global.netplay.nickname=
global.netplay.port=55435
global.netplay.relay=
global.netplay.systems=fbneo,mame,mastersystem,megadrive,neogeo,nes,pcengine,sega32x,sg1000,snes,supergrafx,atari2600,pcenginecd,pcfx,fds,tic80,segacd,mrboom,colecovision
global.netplay.lobby=http://lobby.libretro.com/list/
## Configurations generated by Recalbox
emulationstation.theme.recalbox-next.colorset=1-light blue colors
emulationstation.theme.recalbox-next.gameclipview=0 - DEFAULT
emulationstation.theme.recalbox-next.gamelistview=1-standard gamelist
emulationstation.theme.recalbox-next.region=us
emulationstation.theme.recalbox-next.iconset=1-standard icons
emulationstation.theme.recalbox-next.menuset=1-light blue icons
emulationstation.theme.recalbox-next.systemview=1-vertical left
system.firsttimeuse=0
emulationstation.pad1=030000005e0400008e02000020010000:Xbox 360 Controller
emulationstation.pad0=030000005e0400008e02000014010000:Xbox 360 Controller

config.ini

 [generic]
; Device Tree Overlay
overlay_resize=16384
; uncomment next line to enable Odroid XU4 OGST
overlay_profile=hktft_cs_ogst
overlays="spi0 i2c0 i2c1 uart0"
 
[overlay_hktft_cs_ogst]
overlays="hktft-cs-ogst i2c0"

manitou · 3 Jul 2021, 07:45

@loli72 merci beaucoup
Quel logiciel utilises tu pour avoir ce type d'affichage ?

loli72 · 4 Jul 2021, 16:12

@manitou
Tu veux dire le fond gris ?
Aucun, c'est là une option de l'éditeur de texte de ce forum , l'option code "</>".
Mais tu peux utiliser notepad++ pour faire ressortir les lignes importantes en couleur en jouant sur le menu "langage".

manitou · 5 Jul 2021, 06:22

@loli72 ah oui en effet ^^
Néanmoins, vraiment étrange car même avec un copier coller de ton contenu toujours aucun affichage sur l’écran.
La je comprends vraiment pas car je suis certain que l’écran marche ....
Je suis entrain de me demander si cela ne peut pas provenir d'un probleme de compatibilité de la version de la carte ou de la carte SD avec la 7.2.2
En plus je pense que nous devons plus être beaucoup sur le XU4 d’où surement la raison pour laquelle je n'ai eu aucun retour sur mon poste.

ViRuS-MaN · 5 Jul 2021, 14:58

bonjour
le fichier config.ini il est ou exactement sur la carte sd ???

flaker38 · 5 Jul 2021, 19:11

@manitou Salut,
J'ai ressorti mon XU4 pour tester cette version de Recalbox et je trouve que cette 7.2.2 marche plutôt bien sur le XU4 (pour la N64 du moins).
Concernant l'écran OGST, pas de problème pour le faire fonctionner, comme @loli72 .
Par rapport à la 7.0, il faut bien mettre system.secondminitft.type=overlay dans \\recalbox\share\system\recalbox.conf et surtout enlever le ";" sur la ligne overlay_profile=hktft_cs_ogst du fichier config.ini à la racine de la partition Recalbox

@manitou As-tu utilisé notepad++ pour éditer tes fichiers ? (le notepad de base ne gère pas bien les caractères de fin de ligne).

manitou · 5 Jul 2021, 22:10

@flaker38 Merci pour ton retour
Je viens de refaire une installation complète en utilisant notepad++ pour éditer les 2 fichiers et toujours même problème.... la franchement je commence à désespérer car je ne vois vraiment pas d’où peut provenir le problème tellement cela est simple....

Même si je pense que le problème n'est pas lié, je viens de m'apercevoir que si j'effectue un copier coller du contenu partagé par loli72, je ne me retrouve pas avec le même nombre de ligne dans mon document. Sur le fichier config.ini qui doit faire 9 lignes, quand j'effectue un copier coller dans mon fichier, je me retrouve à 18 lignes.
Néanmoins quand j'ai édité les fichiers je n'ai pas eu le problème , le nombre de ligne n'avait pas changé

@ViRuS-MaN le fichier config.ini est à la la racine de la partition Recalbox sur la carte SD

manitou · 6 Jul 2021, 15:49

@manitou petite précision, je viens d'utiliser le fichier image que XXXX a créer sous la version 7.1.1 est mon écran fonctionne ...

LA DISTRIBUTION DE LIENS VERS DU CONTENU SOUS DROIT D'AUTEUR EST INTERDITE.

Néanmoins il a déjà modifié le fichier recalbox.conf pour faire fonctionner l'ecran

@flaker38 a tout hasard tu n'as pas une sauvegarde du setup 7.1.1 d'origine afin que je procède à un essai pour voir si cela provient uniquement de la version 7.2.2 chez moi ?

ViRuS-MaN · 6 Jul 2021, 08:08

j ai bien un fichier config.ini.sample a la racine mais pas de fichier config.ini

loli72 · 6 Jul 2021, 14:07

@flaker38 Et, sur l'écran OGST
, les vidéos ne sont pas saccadées par rapport aux versions précédentes ?

Retour 7.2.2 sur XU4

Want to support us ?

74
Online

98.0k
Users

28.0k
Topics

186.9k
Posts

	# System Variable
	# You can configure your recalbox from here
	# To set a variable, remove the first ; on the line

	# NOTE ON CEC FOR REMOTES
	# you've to plug the ODROID XU4 on the HDMI1 of your tv
	# this is a limitation of the EXYNOS libcec adapter


	# ------------ A - System Options ----------- #
	# Uncomment the system.power.switch you use
	;system.power.switch=ATX_RASPI_R2_6 # http://lowpowerlab.com/atxraspi/#installation
	;system.power.switch=MAUSBERRY # http://mausberry-circuits.myshopify.com/pages/setup
	;system.power.switch=REMOTEPIBOARD_2003 # http://www.msldigital.com/pages/support-for-remotepi-board-2013
	;system.power.switch=REMOTEPIBOARD_2005 # http://www.msldigital.com/pages/support-for-remotepi-board-plus-2015
	;system.power.switch=WITTYPI # http://www.uugear.com/witty-pi-realtime-clock-power-management-for-raspberry-pi
	;system.power.switch=PIN56ONOFF # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)
	;system.power.switch=PIN56PUSH # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)
	;system.power.switch=PIN356ONOFFRESET # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)

	## Splash screen duration
	## 0 : Video will be stopped when emulationstation is ready to start.
	## -1 : All the video will be played before emulationstation start (default)
	## >0 : Time the video will be played before emulationstation start (in seconds)
	system.splash.length=-1
	## Splash videos selection
	## all: select a boot video in recalbox videos and user videos
	## recalbox: select a boot video only in recalbox videos
	## custom: select a boot video only in user videos
	## Any invalid value means "all"
	system.splash.select=all

	## Recalbox Manager (http manager)
	system.manager.enabled=1
	## Currently, only version 2 is available
	system.manager.version=2

	## Recalbox security
	# enforce security
	# samba password required
	# disable virtual gamepads
	system.security.enabled=0

	## Recalbox API (REST)
	system.api.enabled=0

	## EmulationStation
	### menu style
	### default -> default all options menu
	### none -> no menu except the game search menu
	### bartop -> less menu, only needed for bartops
	emulationstation.menu=default
	### Select a system to show on boot (use rom directory name) (string)
	emulationstation.selectedsystem=favorites
	### Show the gamelist of the first or selected system on boot (0,1)
	emulationstation.bootongamelist=0
	### Disable system view. ES will boot and show ONLY the first or selected system (0,1)
	emulationstation.hidesystemview=0
	### Pa&ast;&ast;e Gamelists only. Show only games listed in gamelist.xml files (0,1)
	emulationstation.gamelistonly=0
	### Force basicgameList view to be displayed, even if your game systems are scraped (0,1)
	emulationstation.forcebasicgamelistview=0
	### Filter out adult games
	### you may use emulationstation.snes.filteradultgames=1
	### to filter out adult games for the snes system or any other system
	;emulationstation.filteradultgames=1
	### Zipped gamelist preference
	### Whatever you choose, emulationstation can read both compressed
	### and uncompressed gamelist.xml or gamelist.zip
	### However updated gamelist will be saved in your prefered format.
	### Zipped format may save load time, especially on slow devices.
	### 0 = gamelist.xml
	### 1 = gamelist.zip
	;emulationstation.zippedgamelist=1

	## Arcade metasystem
	## Activate the Arcade metasystem to group all games from piFBA, FBN (libretro), MAME and optionally Neogeo
	## into a single "Arcade" system.
	;emulationstation.arcade=1
	## You may want to specify its position in the system list. (Default: 0)
	## Negatives values may be used to tart from the end (-1 = last position)
	;emulationstation.arcade.position=0
	## Include NeoGeo or not (default: 1)
	;emulationstation.arcade.includeneogeo=1
	## Hide included system or leave them in the system list (default: 1)
	;emulationstation.arcade.hideoriginals=1

	## Virtual systems
	### Activate a virtual system with all games available from all systems
	;emulationstation.collection.allgames=1
	### Activate a virtual system with all multiplayer games (players >= 2)
	;emulationstation.collection.multiplayers=1
	### Activate a virtual system with last played games
	;emulationstation.collection.lastplayed=1

	## Videosnaps
	### Delay before videosnaps start, in millisecond. Default: 2s
	;emulationstation.videosnaps.delay=2000
	### Video loop times. 0 = no video. 1 or more = the video loops x times before fading out
	;emulationstation.videosnaps.loop=1
	### Enable videosnap sound/music
	;emulationstation.videosnaps.sound=1

	## Scrapers
	### Activate this option to extract region from filename when possible
	;scraper.extractregionfromfilename=1
	### Select the source of game's names
	### 0 = from scrapper result (default)
	### 1 = from filename
	### 2 = from filename undecorated (i.e: (text) and [text] removed)
	;scraper.getnamefrom=0
	### ScreenScraper.fr
	### Force media region - if not defined, region is taken from system.language. Default: us
	;scraper.screenscraper.region=eu
	### Force text language - if not defined, region is taken from system.language. Default: en
	;scraper.screenscraper.language=fr
	### Choose the media to download among:
	### screenshot: game screenshot
	### title : game title screenshot
	### box2d : Front case
	### box3d : 3D rendered case
	### mixv1 : Recalbox special mix image V1 (default)
	### mixv2 : Recalbox special mix image V2
	;scraper.screenscraper.media=mixv1
	### ScreenScraper account
	;scraper.screenscraper.user=
	;scraper.screenscraper.password=

	## Emulator special keys
	## default -> default all special keys
	## nomenu -> cannot popup the emulator menu
	## none -> no special keys in emulators
	system.emulators.specialkeys=default

	## Show or hide kodi in emulationstation (0,1)
	kodi.enabled=0
	## Start kodi at launch (0,1)
	kodi.atstartup=0
	## set x button shortcut (0,1)
	kodi.xbutton=0

	## Kodi can wait for a network component before starting
	## waithost is the ip or hostname that must answer to a ping to validate the availability
	## waittime is the maximum time waited when kodi boots
	## if waitmode is required, kodi will not start if the component is not available
	## if waitmode is wish, kodi will start if the component is not available
	## if waitmode is not set or has another value, kodi will start immediately
	;kodi.network.waitmode=required
	;kodi.network.waittime=10
	;kodi.network.waithost=192.168.0.50



	# ------------ B - Network ------------ #
	## Set system hostname
	system.hostname=RECALBOX
	## Activate wifi (0,1)
	wifi.enabled=0
	## Set wifi region
	## More info here: https://github.com/recalbox/recalbox-os/wiki/Wifi-country-code-(EN)
	wifi.region=JP
	## Wifi SSID (string)
	;wifi.ssid=new ssid
	## Wifi KEY (string)
	## after rebooting the recalbox, the "new key" is replace by a hidden value "enc:xxxxx"
	## you can edit the "enc:xxxxx" value to replace by a clear value, it will be updated again at the following reboot
	## Escape your special chars (# ; $) with a backslash : $ => \$
	;wifi.key=new key

	## Wifi - static IP
	## if you want a static IP address, you must set all 3 values (ip, gateway, and netmask)
	## if any value is missing or all lines are commented out, it will fall back to the
	## default of DHCP
	;wifi.ip=manual ip address
	;wifi.gateway=new gateway
	;wifi.netmask=new netmask

	# secondary wifi (not configurable via the user interface)
	;wifi2.ssid=new ssid
	;wifi2.key=new key

	# third wifi (not configurable via the user interface)
	;wifi3.ssid=new ssid
	;wifi3.key=new key

	## Samba share
	system.samba.enabled=1
	### Virtual Gamepads
	system.virtual-gamepads.enabled=1
	### SSH
	system.ssh.enabled=1



	# ------------ C - Audio ------------ #
	## Set the audio device (auto, hdmi, jack)
	audio.device=alsa_card.0:hdmi-output-0
	## Set system volume (0..100)
	audio.volume=90
	## Enable or disable system sounds in ES (0,1)
	audio.bgmusic=1



	# -------------- D - Controllers ----------------- #
	# Enable support for standard bluetooth controllers
	controllers.bluetooth.enabled=1
	# Enable ERTM
	controllers.bluetooth.ertm=1


	## Please enable only one of these
	# -------------- D1 - PS3 Controllers ------------ #
	##Enable PS3 controllers support
	controllers.ps3.enabled=1
	## Choose a driver between bluez, official and shanwan
	## bluez -> bluez 5 + kernel drivers, support official and shanwan sisaxis
	## official -> sixad drivers, support official and gasia sisaxis
	## shanwan -> shanwan drivers, support official and shanwan sisaxis
	controllers.ps3.driver=bluez


	# ------------ D2 - GPIO Controllers ------------ #
	## GPIO Controllers
	## enable controllers on GPIO with mk_arcarde_joystick_rpi (0,1)
	controllers.gpio.enabled=0
	## mk_gpio arguments, map=1 for one controller, map=1,2 for 2 (map=1,map=1,2)
	controllers.gpio.args=map=1,2


	## DB9 Controllers
	## Enable DB9 drivers for atari, megadrive, amiga controllers (0,1)
	controllers.db9.enabled=0
	## db9 arguments
	controllers.db9.args=map=1

	## Gamecon controllers
	## Enable gamecon controllers, for nes, snes, psx (0,1)
	controllers.gamecon.enabled=0
	## gamecon_args
	controllers.gamecon.args=map=1

	## XGaming's XArcade Tankstik and other compatible devices
	controllers.xarcade.enabled=1

	# ------------ D3 - Joycon Controllers ------------ #
	controllers.joycond.enabled=1


	# ------------ E - Language and keyboard ------------ #
	## Set the language of the system (fr_FR,en_US,en_GB,de_DE,pt_BR,es_ES,it_IT,eu_ES,tr_TR,zh_CN)
	system.language=fr_FR
	## set the keyboard layout (fr,en,de,us,es)
	system.kblayout=fr
	## Set you local time
	## Select your timezone from : ls /usr/share/zoneinfo/ (string)
	;system.timezone=Europe/Paris



	# ------------ F - UPDATES ------------ #
	## Automatically check for updates at start (0,1)
	updates.enabled=1
	# Update type : default to stable
	updates.type=stable



	# ------------ G - HERE IT IS - GLOBAL EMULATOR CONFIGURATION ------------ #
	## The global value will be used for all emulators, except if the value
	## is redefined in the emulator

	## Set game resolution for emulators
	## Please don't modify this setting
	## This arch does not support the video mode switch
	## (string)
	global.videomode=default

	## Shader set
	## Automatically select shaders for all systems
	## (none, retro, scanlines)
	global.shaderset=none

	## Once enabled, your screen will be cropped, and you will have a pixel perfect image (0,1)
	global.integerscale=0

	## Set gpslp shader for all emulators (prefer shadersets above). Absolute path (string)
	global.shaders=

	## Set ratio for all emulators (auto,4/3,16/9,16/10,custom)
	global.ratio=auto

	## Set smooth for all emulators (0,1)
	global.smooth=1

	## Set rewind for all emulators (0,1)
	global.rewind=1

	## Set autosave/load savestate for all emulators (0,1)
	global.autosave=0

	## Enable retroarchievements (0,1)
	## Set your www.retroachievements.org username/password
	## Escape your special chars (# ; $) with a backslash : $ => \$
	global.retroachievements=0
	global.retroachievements.hardcore=0
	global.retroachievements.username=
	global.retroachievements.password=

	## Set retroarch input driver (auto, udev, sdl2)
	## If you don't have issues with your controllers, let auto
	global.inputdriver=auto

	## If you do not want recalboxOS to generate the configuration for all emulators (string)
	;global.configfile=/path/to/my/configfile.cfg

	## Demo screensaver parameters
	## Set the system list from which ES will run random games
	## Empty list or unexisting key means all available systems
	global.demo.systemlist=3do,amigacd32,atari2600,atari5200,atari7800,daphne,fbneo,fds,gamegear,gba,lynx,mame,mastersystem,megadrive,neogeo,nes,ngpc,pcengine,sega32x,sg1000,snes
	## Default demo game sessions last 90s. Change this value if you want shorter or longer sessions
	;global.demo.duration=90
	## Default game info screen duration lasts 6s. Change this value if you want shorter or longer info screens.
	;global.demo.infoscreenduration=6

	## Retroarch AI Translation service
	## Comment out or set to 0 the following key if you don't want the AI service
	global.translate=1
	## Set the source and the target languages.
	## Allowed language list: EN, ES, FR, IT, DE, JP, NL, CS, DA, SV, HR, KO, ZH_CN, ZH_TW, CA, BG, BN, EU, AZ, AR, SQ,
	## AF, EO, ET, TL, FI, GL, KA, EL, GU, HT, IW, HI, HU, IS, ID, GA, KN, LA, LV, LT, MK, MS,
	## MT, NO, FA, PL, PT, RO, RU, SR, SK, SL, SW, TA, TE, TH, TR, UK, UR, VI, CY, YI
	## Setting the translate.from key to a specified language may speed up or give more accurate results
	## If translate.to key is commented, the default value is extracted from system.language or, if system.language is
	## undefined, set to auto (=EN).
	global.translate.from=auto
	global.translate.to=auto
	## zTranslate API Key
	## go to https://ztranslate.net and create an account.
	## validate your account, then log in and go to the settngs page
	## Look for the API Key at the bottom of the page, then uncomment the following key and paste your API Key:
	;global.translate.apikey=RECALBOX
	## Other translation service
	## If you want to use another translation service or a custom API call, use this key to
	## specify the url to call. If the key is not empty, it is used instead of zTranslation's API Key
	;global.translate.url=



	# ------------ H - EMULATORS CHOICES ----------- #
	## You can override the global configurations here
	## Here is the snes example
	;snes.core=snes9x2010
	;snes.shaders=/recalbox/share/shaders/shaders_glsl/mysnesshader.gplsp
	;snes.ratio=16/9
	;snes.smooth=0
	;snes.rewind=1
	;snes.autosave=0
	;snes.emulator=libretro
	;snes.integerscale=0
	## If you do not want recalboxOS to generate the configuration for the emulator:
	;snes.configfile=/path/to/my/configfile.cfg

	## Default cores for Odroid XU4
	;snes.core=snes9x
	n64.core=gliden64

	## NeoGeo emulator
	## You can use pifba or a libretro core (fba2x,libretro)
	neogeo.emulator=libretro
	## If you set libretro as neogeo.emulator, the line below sets the retroarch core (fbneo, mame2000)
	neogeo.core=fbneo

	## Demo screensaver parameters
	## Include or exclude a particular system from the demo screensaver
	## You may change the global.demo.systemlist key or include/exclude every single system
	;snes.demo.include=0
	## Set the session duration for a particular system
	;snes.demo.duration=90



	# ------------ J - TFT SECONDARY SCREEN ----------- #
	#Second miniTFT screen as marquee to display scrapes and videos
	#Enable it with system.secondMiniTFT.enabled=1, disable with system.secondMiniTFT.enabled=0

	#this configuration is REQUIRED
	system.secondminitft.enabled=1

	#Type of mini TFT : OGST, unknown
	#Most of spi tft screen are enabled thanks to overlays in /boot/config.txt in rpi and /boot/config.ini on odroidxu4
	#please check the specific configuration of your screen
	#Some examples are available on the page .....
	# values are :
	# - overlay : screen configured through overlays in /boot/config.txt or /boot/config.ini (odroidxu4/ogst)
	# - default : the rest of the world
	#this configuration is REQUIRED if system.secondminitft.enabled=1
	system.secondminitft.type=overlay

	#Choose the resolution of your screen
	#miniTFT resolution 320x240 -> 240p, 480x320 -> 320p

	#this configuration is REQUIRED if system.secondminitft.enabled=1
	system.secondminitft.resolution=240p

	#Scraped image aspect on tft screen : fbv display option
	# options available : stretch, ignore-aspect, enlarge.
	# stretch : Strech (using a simple resizing routine) the image to fit onto screen if necessary
	# alpha : use the alpha channel (if applicable)
	# ignore-aspect : Ignore the image aspect while resizing
	# enlarge : Enlarge the image to fit the whole screen if necessary

	# 1 = enabled, 0 = disabled

	#this configuration is REQUIRED if system.secondminitft.enabled=1
	system.secondminitft.imagestretchenabled=1
	system.secondminitft.imageenlargeenabled=0
	system.secondminitft.imagealphaenabled=1
	system.secondminitft.imageignoreaspectenabled=1

	#When activating the second TFT screen, you may want to display
	#game scraped video only on the second screen. This variable
	#allows you to disable scraped video playing in ES during game browsing
	#system.secondminitft.disablevideoines=1 disable video playing in ES
	#system.secondminitft.disablevideoines=0 enable video playing in ES

	#this configuration is OPTIONAL if system.secondminitft.enabled=1
	system.secondminitft.disablevideoines=1

	#if the backlight of your your screen can be manage by PWM,
	#indicates the GPIO value of your PWM control
	#WiringPi and its gpio program will be used to control the backlight
	#when RB goes in SLEEP mode, and when it wakes up.
	#On raspberry pi, PWMs cannot be used simultaneously with Jack sound output.
	#If your are using HDMI or a Audio hat you can use backlight PWM control for the second screen
	#If you are using Jack output please leave commented.
	#The Screen will be switch down in Sleep mode, and switch on when it wakes up.
	#On OGST, only this mode is available.

	#this configuration is OPTIONAL if system.secondminitft.enabled=1
	;system.secondminitft.backlightcontrol=18

	# system.secondminitft.usemarquee variabla allows you to display a different
	# image during running game. just creat a directory named "marquees" in media
	# aside videos and images and put new images with the same name as in images
	# example :
	# - /recalbox/share/roms/neogeo/media/marquees/alpham2.png
	# - /recalbox/share/roms/neogeo/media/images/alpham2.png
	# if set to 1, in game the marquee images will be displayed
	# if set to 0, in game the scraped images will be displayed
	;system.secondminitft.usemarquee=0

	#system.secondminitft.sleepenabled allows you to enable/disable
	#sleep mode for the second TFT. If set to 1 sleep mode is enabled and
	#backlight of the screen will be OFF. If set to 0, sleep mode is
	#disabled and the backlight of the screen will be always On

	;system.secondminitft.sleepenabled=0

	# ------------ I - NETPLAY PARAMETERS ----------- #
	## All these values are handled by Recalbox itself
	global.netplay=1
	global.netplay.nickname=
	global.netplay.port=55435
	global.netplay.relay=
	global.netplay.systems=fbneo,mame,mastersystem,megadrive,neogeo,nes,pcengine,sega32x,sg1000,snes,supergrafx,atari2600,pcenginecd,pcfx,fds,tic80,segacd,mrboom,colecovision
	global.netplay.lobby=http://lobby.libretro.com/list/

	## Configurations generated by Recalbox
	emulationstation.theme.recalbox-next.colorset=1-light blue colors
	emulationstation.theme.recalbox-next.gameclipview=0 - DEFAULT
	emulationstation.theme.recalbox-next.gamelistview=1-standard gamelist
	emulationstation.theme.recalbox-next.region=us
	emulationstation.theme.recalbox-next.iconset=1-standard icons
	emulationstation.theme.recalbox-next.menuset=1-light blue icons
	emulationstation.theme.recalbox-next.systemview=1-vertical left
	system.firsttimeuse=0
	emulationstation.pad1=030000005e0400008e02000020010000:Xbox 360 Controller
	emulationstation.pad0=030000005e0400008e02000014010000:Xbox 360 Controller

	[generic]
	; Device Tree Overlay
	overlay_resize=16384
	; uncomment next line to enable Odroid XU4 OGST
	overlay_profile=hktft_cs_ogst
	overlays="spi0 i2c0 i2c1 uart0"

	[overlay_hktft_cs_ogst]
	overlays="hktft-cs-ogst i2c0"

Retour 7.2.2 sur XU4

Want to support us ?

74Online

98.0kUsers

28.0kTopics

186.9kPosts

74
Online

98.0k
Users

28.0k
Topics

186.9k
Posts