7.2 can no longer pair 8bitdo SN30 pro+ controllers

[lhari84]

Sorry, I was confused with the model name too. I got the SF30 Pro (non +). It seems to be technically the same as SN30 Pro (non +).
Anyway, as mentioned before, I got problem the controller pairs but is not working at all - not even in ES/menu. I'm on latest firmware 1.34. Further not tried too much changing controller mode. It worked fine in "Switch mode" with Recalbox 7.1.1 and before.

Further one nice feature is, the controller switches off automatically when shutting down Recalbox when in "Switch mode", so I won't try again other modes at all as far as it might not necessary. In worst case I will restore my backup of Recalbox 7.1.1.

Anyway, thanks to developers for new version and the hard work!

[LostOldman]

@lhari84

I am new to all of this, is there a place I can download version 7.1.1 again. I dont have a backup of it that I know of. I will for the versions in the future.

[KoCinsKy]

@erokx said in 7.2 can no longer pair 8bitdo SN30 pro+ controllers:

change driver from automatic to "system"

With this, my sn30 works.

[lhari84]

@LostOldman
As far as I know, old versions are always replaced when new ones released. I recommend to backup whole SD card with a disk imaging tool before doing an update.

[lhari84]

@KoCinsKy
Unfortunately this does not help for SF30 pro, as it pairs in general, but on the other hand Recalbox (even ES/menu) will not react in any way then.
Also controller setup will not find the controller even though it‘s paired, no button configuration possible too.

[lhari84]

Update:
After restore of Recalbox 7.1.1, my SF30 pro controller works fine again, as expected.

[LostOldman]

Update:
After a fresh install of 7.2, and my 8bitdo controllers work fine in B_Start mode in the main menu's but when I go to any game I have to turn off the controllers and then turn them on again to pair them. After that they will work in the games. The Hotkey does cycle through the shaders. I found an almost identical issue in the forums for version 7.0.1.

https://forum.recalbox.com/topic/22222/7-0-1-controller-works-in-emulationstation-but-not-in-retroarch

[lhari84]

No one else having described troubles with Pi3 B+ and SN/SF30 pro (non+ version: https://www.8bitdo.com/sn30pro-sf30pro/)? Could it be just because of updating from 7.1.1 to 7.2? May a fresh install of 7.2 help?

[Scavy]

@lhari84
Known issues with SN30 pro, SF30 pro and SN30 pro + pads. It concerns firmwares of these pads.
Here are the right firmware to use (tested et approved by beta-testers) :
Appairing in android mode START + B :
SN30 Pro -> firmware v1.33
SN30 Pro + -> firmware v4.01
SF30 Pro -> firmware v1.33
Last firmware updates don't work fine. A fix is in progress.

[lhari84]

@Scavy Thank you very much for info, great news that there's a fix coming up. Haven't seen any note in changelog, so I was not sure so far.

Do you know if controllers turn off automatically too when shutting down recalbox, when in Andtroid-mode?
Normally I always use 8bitdo controllers in Switch-mode, as I really appreciate this behaviour not having to turn off the controller separately
If not, I will wait for the RB fix and/or 8bitdo fix instead of downgrading my controllers. Everything I need is running fine in 7.1.1

[Scavy]

@lhari84 my 8bitdo controllers turns off but not when i shut down recalbox but coz of the delay : 3 ou 5 mns after no use, they shut down.

[Hurricane]

Hi,

I tried to install Firmware v1.37 (date 2021.07.16) on 8BitDo SN30PRO and it still doesn't work. Firmware version v1.33 also doesn't work for me. Can I ask for help?