Partie manquante config.txt

[eikichi76]

D'accord, donc pour config.txt j'ai juste à crée la ligne 1 exactement comme sur ton screen et c'est tous ? Pour le 480 entrelacé je mets simplement hdmi mode 6 ? Pour besoin de rien crée d'autre ?

[eikichi76]

bon bah apres essai sur mon crt avec config.txt et recalbox.conf modifié , je me retrouve avec simplement des couleur qui sautille , pas une seul image .. je vous post mon config.txt et recalbox.conf , si jamais vous voyez quelques que j'aurai mal fait ..

config.txt:

merci pour votre aide

[acris]

@eikichi76
essaie d'utiliser la syntaxe markdown pour le code :
https://github.com/adam-p/markdown-here/wiki/Markdown-Cheatsheet#code

#Définition de la résolution du mode custom DTM 87 HDMI pour la résolution des jeux
hdmi_cvt=1920 240 60 1 1 0 0

#Ignore la EDID de votre tv
hdmi_ignore_edid=0xa5000080

#force le mode d'encodage des pixels, 2 correspond à FULL RGB
hdmi_pixel_encoding=2

# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1

disable_overscan=1

# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=6

# Sound output. Set to 0 or comment for autodetect, 1 for DVI, 2 to force HDMI.
#hdmi_drive=2

# Using /etc/modules is deprecated and no longer supported on 4.4 kernel
# So manually enable audio
dtparam=audio=on

config_hdmi_boost=0

# force hdmi while the tv can take time before sending the signal on the hdmi output
hdmi_force_hotplug=1

# uncomment for composite PAL
#sdtv_mode=2

# uncomment for lirc-rpi
#dtoverlay=lirc-rpi

# if you plug your tv at the same time as your rpi and that the rpi switches from the hdmi or give a low resolution because tv had no enough time to initialize it
boot_delay=3

# uncomment if you don't want the rainbow at startup
disable_splash=1

# default CEC name
cec_osd_name=recalbox

# Overclock
gpu_mem_256=128
gpu_mem_512=256
gpu_mem_1024=448

avoid_safe_mode=1

kernel=zImage

# Raise the first security limit up to 70° instead of 60°
temp_soft_limit=70

recalbox.conf:

# System Variable
# You can configure your recalbox from here
# To set a variable, remove the first ; on the line



# ------------ A - System Options ----------- #
#    Uncomment the system.power.switch you use
;system.power.switch=ATX_RASPI_R2_6      # http://lowpowerlab.com/atxraspi/#installation
;system.power.switch=MAUSBERRY           # http://mausberry-circuits.myshopify.com/pages/setup
;system.power.switch=REMOTEPIBOARD_2003  # http://www.msldigital.com/pages/support-for-remotepi-board-2013
;system.power.switch=REMOTEPIBOARD_2005  # http://www.msldigital.com/pages/support-for-remotepi-board-plus-2015
;system.power.switch=WITTYPI             # http://www.uugear.com/witty-pi-realtime-clock-power-management-for-raspberry-pi
;system.power.switch=PIN56ONOFF          # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)
;system.power.switch=PIN56PUSH           # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)
;system.power.switch=PIN356ONOFFRESET    # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)
;system.power.switch=PIN356PUSHRESET     # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)

## fbcp FrameBuffer Copy Program
## For small TFT screen on GPIO and SPI
## See https://github.com/recalbox/recalbox-os/wiki/Utility---Use-of-fbcp-for-small-TFT-screen-%28EN%29 for details
## Needed for Waveshare 3.2" 3.5" TFT screen, 2.8" Adafruit screen
## See https://github.com/recalbox/recalbox-os/wiki/TFT-Screen-SPI-Bus-%28EN%29
## for support and configuration details needed by /boot/config.txt
system.fbcp.enabled=0

## Splash screen duration
## 0: Video will be played for 20 seconds (default)
## -1: All the video will be played (it won't be stopped automatically)
## >0 : Time before the video will be stopped (in seconds)
system.splash.length=0

## Recalbox Manager (http manager)
system.manager.enabled=1
## Currently, only version 2 is available
system.manager.version=2

## Recalbox security
# enforce security
# samba password required
# disable virtual gamepads
system.security.enabled=0

## Recalbox API (REST)
system.api.enabled=0

## Allow a specific resolution for ES only from the command : tvservice -m [MODE]
## Leave commented for the default usual behaviour
;system.es.videomode=CEA 6 HDMI

## EmulationStation
### menu style
### default -> default all options menu
### none -> no menu except the game search menu
### bartop -> less menu, only needed for bartops
emulationstation.menu=default
### Select a system to show on boot (use rom directory name) (string)
emulationstation.selectedsystem=favorites
### Show the gamelist of the first or selected system on boot (0,1)
emulationstation.bootongamelist=0
### Disable system view. ES will boot and show ONLY the first or selected system (0,1)
emulationstation.hidesystemview=0
### Pa**e Gamelists only. Show only games listed in gamelist.xml files (0,1)
emulationstation.gamelistonly=0
### Force basicgameList view to be displayed, even if your game systems are scraped (0,1)
emulationstation.forcebasicgamelistview=0

## Videosnaps
### Delay before videosnaps start, in millisecond. Default: 2s
;emulationstation.videosnaps.delay=2000
### Video loop times. 0 = no video. 1 or more = the video loops x times before fading out
;emulationstation.videosnaps.loop=1

## Scrapers
### ScreenScraper.fr
### Force media region - if not defined, region is taken from system.language. Default: us
;scraper.screenscraper.region=eu
### Force text language - if not defined, region is taken from system.language. Default: en
;scraper.screenscraper.language=fr
### Choose the media to download among:
### screenshot: game screenshot
### title     : game title screenshot
### box2d     : Front case
### box3d     : 3D rendered case
### mixv1     : Recalbox special mix image V1 (default)
### mixv2     : Recalbox special mix image V2
;scraper.screenscraper.media=mixv1
### ScreenScraper account
;scraper.screenscraper.user=
;scraper.screenscraper.password=

## Emulator special keys
## default -> default all special keys
## nomenu -> cannot popup the emulator menu
## none -> no special keys in emulators
system.emulators.specialkeys=default

## Show or hide kodi in emulationstation (0,1)
kodi.enabled=1
## Start kodi at launch (0,1)
kodi.atstartup=0
## set x button shortcut (0,1)
kodi.xbutton=1

## Allow a specific resolution for Kodi only from the command : tvservice -m [MODE]
## By default is using the default resolution of your screen
kodi.videomode=default

## Kodi can wait for a network component before starting
## waithost is the ip or hostname that must answer to a ping to validate the availability
## waittime is the maximum time waited when kodi boots
## if waitmode is required, kodi will not start if the component is not available
## if waitmode is wish, kodi will start if the component is not available
## if waitmode is not set or has another value, kodi will start immediately
;kodi.network.waitmode=required
;kodi.network.waittime=10
;kodi.network.waithost=192.168.0.50

## Hyperion
## Hyperion allows you to use an ambilight like led system on your recalbox
## Use hypercon to create your configuration file, and copy it in /recalbox/share/system/configs/hyperion/hyperion.config.json
hyperion.enabled=0


# ------------ B - Network ------------ #
## Set system hostname
system.hostname=RECALBOX
## Activate wifi (0,1)
wifi.enabled=1
## Set wifi region
## More info here: https://github.com/recalbox/recalbox-os/wiki/Wifi-country-code-(EN)
wifi.region=US
## Wifi SSID (string)
wifi.ssid=Livebox-E614
## Wifi KEY (string)
## after rebooting the recalbox, the "new key" is replace by a hidden value "enc:xxxxx"
## you can edit the "enc:xxxxx" value to replace by a clear value, it will be updated again at the following reboot
## Escape your special chars (# ; $) with a backslash : $ => \$
wifi.key=vYac5hcNckpPTabGNo

## Wifi - static IP
## if you want a static IP address, you must set all 3 values (ip, gateway, and netmask)
## if any value is missing or all lines are commented out, it will fall back to the
## default of DHCP
;wifi.ip=manual ip address
;wifi.gateway=new gateway
;wifi.netmask=new netmask

# secondary wifi (not configurable via the user interface)
;wifi2.ssid=new ssid
;wifi2.key=new key

# third wifi (not configurable via the user interface)
;wifi3.ssid=new ssid
;wifi3.key=new key

## Samba share
system.samba.enabled=1
### Virtual Gamepads
system.virtual-gamepads.enabled=1
### SSH
system.ssh.enabled=1

# ------------ C - Audio ------------ #
## Set the audio device (auto, hdmi, jack)
audio.device=auto
## Set system volume (0..100)
audio.volume=100
## Enable or disable system sounds in ES (0,1)
audio.bgmusic=1



# -------------- D - Controllers ----------------- #
# Enable support for standard bluetooth controllers
controllers.bluetooth.enabled=1
# Enable ERTM
controllers.bluetooth.ertm=0


## Please enable only one of these
# -------------- D1 - PS3 Controllers ------------ #
##Enable PS3 controllers support
controllers.ps3.enabled=1
## Choose a driver between bluez, official and shanwan
## bluez -> bluez 5 + kernel drivers, support official and shanwan sisaxis
## official -> sixad drivers, support official and gasia sisaxis
## shanwan -> shanwan drivers, support official and shanwan sisaxis
controllers.ps3.driver=bluez


# ------------ D2 - GPIO Controllers ------------ #
## GPIO Controllers
## enable controllers on GPIO with mk_arcarde_joystick_rpi (0,1)
controllers.gpio.enabled=1
## mk_gpio arguments, map=1 for one controller, map=1,2 for 2 (map=1,map=1,2)
controllers.gpio.args=map=1,2
## Custom mk_gpio arguments,
## map=5 gpio1=Y-,Y+,X-,X+,start,select,a,b,tr,y,x,tl,hk  for one controller,
## map=5 gpio1=pin1,pin2,pin3,.....,pin12,pin13
## map=5,6 gpio1=Y-,Y+,X-,X+,start,select,a,b,tr,y,x,tl,hk gpio2=Y-,Y+,X-,X+,start,select,a,b,tr,y,x,tl,hk for 2 (map=5,map=5,6)
## map=5,6 gpio1=gpiox,gpioy,gpioz,.....,gpiou,gpiov gpio2=gpiox,gpioy,gpioz,.....,gpiou,gpiov
# where gpiox,gpioy,gpioz ... are NOT pin numbers on the connector, BUT location gpio numbered as in 
# https://www.raspberrypi-spy.co.uk/wp-content/uploads/2012/06/Raspberry-Pi-GPIO-Layout-Model-B-Plus-rotated-2700x900.png
## Set pin to -1 to disable it
# controllers.gpio.args=map=5,6 gpio=4,17,27,22,10,9,25,24,23,18,15,14,2 gpio2=11,5,6,13,19,26,21,20,16,12,7,8,3
## MCP configuration : GPIO and MCP can be used together. You can mix them.
## map=0x20,0x21 for 2 mcp23017 on i2c bus
#controllers.gpio.args=map=0x20,0x21,5,6 gpio=4,17,27,22,10,9,25,24,23,18,15,14,-1 gpio2=11,5,6,13,19,26,21,20,16,12,7,8,-1



# ------------ D3 - Steam Controllers ------------ #
## Enable steam controller service
controllers.steam.enabled=0


## DB9 Controllers
## Enable DB9 drivers for atari, megadrive, amiga controllers (0,1)
controllers.db9.enabled=0
## db9 arguments
controllers.db9.args=map=1

## Gamecon controllers
## Enable gamecon controllers, for nes, snes, psx (0,1) 
controllers.gamecon.enabled=0
## gamecon_args
controllers.gamecon.args=map=1

## XGaming's XArcade Tankstik and other compatible devices
controllers.xarcade.enabled=1



# ------------ F - Language and keyboard ------------ #
## Set the language of the system (fr_FR,en_US,en_GB,de_DE,pt_BR,es_ES,it_IT,eu_ES,tr_TR,zh_CN)
system.language=fr_FR
## set the keyboard layout (fr,en,de,us,es)
system.kblayout=fr
## Set you local time
## Select your timezone from : ls /usr/share/zoneinfo/ (string)
;system.timezone=Europe/Paris



# ------------ G - UPDATES ------------ #
## Automatically check for updates at start (0,1)
updates.enabled=0
# Update type : default to stable
updates.type=stable


# ------------ H - HERE IT IS - GLOBAL EMULATOR CONFIGURATION ------------ #
## The global value will be used for all emulators, except if the value
## is redefined in the emulator

## Set game resolution for emulators
## select your mode from the command : tvservice -m [MODE]
## CEA 5 HDMI : 1920x1080 @ 60Hz 16:9, clock:74MHz interlaced 
## CEA 4 HDMI : 1280x720 @ 60Hz 16:9, clock:74MHz progressive
## use 'default' for using the default resolution
## use 'auto' : switches to CEA 4 HDMI if supported, else keep the current resolution
## (string)
global.videomode=DMT 87 HDMI

## Shader set 
## Automatically select shaders for all systems
## (none, retro, scanlines)
global.shaderset=none

## Once enabled, your screen will be cropped, and you will have a pixel perfect image (0,1)
global.integerscale=0

## Set gpslp shader for all emulators (prefer shadersets above). Absolute path (string)
global.shaders=

## Set ratio for all emulators (auto,4/3,16/9,16/10,custom)
global.ratio=custom

## Set smooth for all emulators (0,1)
global.smooth=1

## Set rewind for all emulators (0,1)
global.rewind=1

## Set autosave/load savestate for all emulators (0,1)
global.autosave=0

## Enable retroarchievements (0,1)
## Set your www.retroachievements.org username/password
## Escape your special chars (# ; $) with a backslash : $ => \$
global.retroachievements=0
global.retroachievements.hardcore=0
global.retroachievements.username=
global.retroachievements.password=

## Set retroarch input driver (auto, udev, sdl2)
## If you don't have issues with your controllers, let auto
global.inputdriver=auto

## If you do not want recalboxOS to generate the configuration for all emulators (string)
;global.configfile=/path/to/my/configfile.cfg

## Demo screensaver parameters
## Set the system list from which ES will run random games.
## Empty list or unexisting key means all available systems
global.demo.systemlist=atari2600,atari5200,atari7800,fba_libretro,fds,gamegear,gba,lynx,mame,mastersystem,megadrive,neogeo,nes,pcengine,sega32x,sg1000,snes
## Default demo game sessions last 90s. Change this value if you want shorter or longer sessions
;global.demo.duration=90
## Default game info screen duration lasts 6s. Change this value if you want shorter or longer info screens.
;global.demo.infoscreenduration=6

## Retroarch AI Translation service
## Comment out or set to 0 the following key if you don't want the AI service
global.translate=1
## Set the source and the target languages.
## Allowed language list: EN, ES, FR, IT, DE, JP, NL, CS, DA, SV, HR, KO, ZH_CN, ZH_TW, CA, BG, BN, EU, AZ, AR, SQ,
##                        AF, EO, ET, TL, FI, GL, KA, EL, GU, HT, IW, HI, HU, IS, ID, GA, KN, LA, LV, LT, MK, MS,
##                        MT, NO, FA, PL, PT, RO, RU, SR, SK, SL, SW, TA, TE, TH, TR, UK, UR, VI, CY, YI
## Setting the translate.from key to a specified language may speed up or give more accurate results
## If translate.to key is commented, the default value is extracted from system.language or, if system.language is
## undefined, set to auto (=EN).
global.translate.from=auto
global.translate.to=auto
## zTranslate API Key
## go to https://ztranslate.net and create an account.
## validate your account, then log in and go to the settngs page
## Look for the API Key at the bottom of the page, then uncomment the following key and paste your API Key:
;global.translate.apikey=YOUR_API_KEY_HERE
## Other translation service
## If you want to use another translation service or a custom API call, use this key to
## specify the url to call. If the key is not empty, it is used instead of zTranslation's API Key
;global.translate.url=

## Arcade metasystem
## Activate the Arcade metasystem to group all games from piFBA, FBN (libretro), MAME and optionally Neogeo
## into a single "Arcade" system.
;global.arcade=1
## You may want to specify its position in the system list. (Default: 0)
## Negatives values may be used to tart from the end (-1 = last position)
;global.arcade.position=0
## Include NeoGeo or not (default: 1)
;global.arcade.includeneogeo=1
## Hide included system or leave them in the system list (default: 1)
;global.arcade.hideoriginals=1


# ------------ I - EMULATORS CHOICES ----------- #
## You can override the global configurations here
## Here is the snes example
;snes.videomode=CEA 4 HDMI
snes.core=snes9x2010
;snes.shaders=/recalbox/share/shaders/shaders_glsl/mysnesshader.gplsp
;snes.ratio=16/9
;snes.smooth=0
;snes.rewind=1
;snes.autosave=0
;snes.emulator=libretro
;snes.integerscale=0
## If you do not want recalboxOS to generate the configuration for the emulator: 
;snes.configfile=/path/to/my/configfile.cfg

## Default cores for RPi3
snes.core=snes9x2010

## NeoGeo emulator 
## You can use pifba or a libretro core (fba2x,libretro)
neogeo.emulator=libretro
## If you set libretro as neogeo.emulator, the line below sets the retroarch core (fbneo, mame2000)
neogeo.core=fbneo

## N64 emulator is configured to display a screen with a 640x480 resolution (native n64 resolution)
## So you must use one of these video modes (DMT 4 HDMI,CEA 1 HDMI).
## If your screen is not compatible with one of these video modes, please check the recalbox's wiki.
n64.videomode=DMT 4 HDMI
## If you are using a CRT screen, please change the setting above with this one : 
# n64.videomode=default

## Dreamcast emulator
## Like N64, such a CPU intensive emulator needs a small resolution
## Consider DMT 4 HDMI (640*480) or DMT 9 HDMI (800*600). If you have a black screen on dreamcast, try DMT 9 HDMI here
dreamcast.videomode=DMT 4 HDMI

## Demo screensaver parameters
## Include or exclude a particular system from the demo screensaver
## You may change the global.demo.systemlist key or include/exclude every single system
;snes.demo.include=0
## Set the session duration for a particular system
;snes.demo.duration=90

# ------------ J - NETPLAY PARAMETERS ----------- #
## All these values are handled by Recalbox itself
global.netplay=1
global.netplay.nickname=
global.netplay.port=55435
global.netplay.relay=
global.netplay.systems=fba_libretro,mame,mastersystem,megadrive,neogeo,nes,pcengine,sega32x,sg1000,snes,supergrafx
global.netplay.lobby=http://lobby.libretro.com/list/

## Configurations generated by Recalbox
amiga600.flatfolder=0
amiga600.sort=0
amiga1200.flatfolder=0
amiga1200.sort=0
atari5200.flatfolder=0
atari5200.sort=0
atari800.flatfolder=0
atari800.sort=0
global.quitpresstwice=0
gba.flatfolder=0
gba.sort=0
psp.flatfolder=0
psp.sort=0
psx.flatfolder=0
psx.sort=0
n64.flatfolder=0
n64.sort=0
imageviewer.flatfolder=0
imageviewer.sort=0
colecovision.flatfolder=0
colecovision.sort=0
channelf.flatfolder=0
channelf.sort=0
c64.flatfolder=0
c64.sort=0
atarist.flatfolder=0
atarist.sort=0
msx2.flatfolder=0
msx2.sort=0
ngpc.flatfolder=0
ngpc.sort=0
ngp.flatfolder=0
ngp.sort=0

[eikichi76]

@acris c'est à dire ? Désolé ça devient compliqué la .. est-ce que j'ai faite des erreurs pour les lignes que j'ai édité ?

[eikichi76]

@eikichi76 said in Partie manquante config.txt:

@acris c'est à dire ? Désolé ça devient compliqué la .. est-ce que j'ai fait des erreurs pour les lignes que j'ai édité ?

[acris]

faut invoquer @ian57 il pourra mieux te guider et contrôler.

[eikichi76]

J'espère qu'il va pouvoir m'aider, c'est la dernière ligne droite pour que la borne que j'ai construite fonctionne enfin .. 1 ans que je suis dessus Snif..

[eikichi76]

Je viens de me rendre compte que cette ligne que j'ai édité " hdmi_cvt=1920 240 60 1 1 0 0 " signifie que le signal est de 60 htz ? Les crt chez nous c'est pas du 50 htz ? Ma tv est une Philips blackline , c'est peut-être pour cela que je n'ai pas d'image non ?

[ian57]

@eikichi76 tu mélange /boot/config.txt et recalbox.conf, lis attentivement la doc

Dans le /boot/config.txt il faut ajouter toutes ces lignes à la fin du fichier

hdmi_cvt=1920 240 60 1 1 0 0
hdmi_disable_edid=0xa5000080 #Enables the ignoring of EDID/display data if your display doesn't have an accurate EDID.
​
hdmi_pixel_encoding=2 #Force the pixel encoding mode. By default it will use the mode requested from edid so shouldn't need changing. 
avoid_safe_mode=1
disable_overscan=0 #oversan enabled
hdmi_drive=2
hdmi_group=1
hdmi_mode=6
hdmi_force=1

ensuite dans le recalbox.conf il faut modifier :

system.es.videomode=CEA 6 HDMI

global.videomode=DMT 87 HDMI

ensuite sur ton câble branche bien la molex pour avoir du 12v sur la broche de la péritel qui te fait passer la TV en mode AV. sinon tu seras oblilger de le faire à la main avec le panel de la tv ou la lélécommande

[eikichi76]

La molex était bien branché, pour recalbox.conf j'en ai 3 l'un sous l'autre. Recalbox.conf et deux recalbox.conf6.1.1 . J'édite bien que le recalbox.conf normal ?

[eikichi76]

bon , j'ai emulstation qui fonctionne sur le crt , mais avec une genre de neige vert et rouge , pas tres jolie .. en revanche j'ai aucune image des que je lance un jeux , juste le son c'est tout . je te post mon config.txt . dit moi stp si quelque chose cloche .

uncomment if you get no picture on HDMI for a default "safe" mode

#hdmi_safe=1

disable_overscan=0

uncomment to force a specific HDMI mode (this will force VGA)

#hdmi_group=1
#hdmi_mode=6

Sound output. Set to 0 or comment for autodetect, 1 for DVI, 2 to force HDMI.

#hdmi_drive=2

Using /etc/modules is deprecated and no longer supported on 4.4 kernel

So manually enable audio

dtparam=audio=on

config_hdmi_boost=4

force hdmi while the tv can take time before sending the signal on the hdmi output

hdmi_force_hotplug=1

uncomment for composite PAL

#sdtv_mode=2

uncomment for lirc-rpi

#dtoverlay=lirc-rpi

if you plug your tv at the same time as your rpi and that the rpi switches from the hdmi or give a low resolution because tv had no enough time to initialize it

boot_delay=3

uncomment if you don't want the rainbow at startup

disable_splash=1

default CEC name

cec_osd_name=recalbox

Overclock

gpu_mem_256=128
gpu_mem_512=256
gpu_mem_1024=448

avoid_safe_mode=1

kernel=zImage

Raise the first security limit up to 70° instead of 60°

temp_soft_limit=70

hdmi_cvt=1920 240 60 1 1 0 0
hdmi_disable_edid=0xa5000080 #Enables the ignoring of EDID/display data if your display doesn't have an accurate EDID.

hdmi_pixel_encoding=2 #Force the pixel encoding mode. By default it will use the mode requested from edid so shouldn't need changing.
avoid_safe_mode=1
disable_overscan=0 #overscan enabled
hdmi_drive=2
hdmi_group=1
hdmi_mode=6
hdmi_force=1

[eikichi76]

Cest bon !! emulationstation fonctionne a la perfection sur mon crt et j'ai enfin les jeux qui fonctionne mais l'image et toute rétrécie au centre de la tv . Comment régler cela ?

[eikichi76]

Set ratio for all emulators (auto,4/3,16/9,16/10,custom)

global.ratio=custom

Est ce que cette ligne doit être sur custom pour prendre en compte le cvt 1900 240 que j'ai créé pour les émulateurs ?

[eikichi76]

Personne pour m'aider ?

[ian57]

@eikichi76

je veux bien t'aider mais il faut que tu mettes un minimum du tien... pour les jeux/émulateurs il faut configurer chaque emulateur libretro (àa marchera pas pour les emu standalon)e avec son fichier de config comme indiquer sur https://recalbox.gitbook.io/tutorials/video/connect-your-recalbox-to-a-crt-with-hdmi-and-scart

then you have to tell libretro for each emulator to use part of the 1920x240 window, for that you have to create a config file for each emu: cf https://forum.recalbox.com/topic/18927/recalbox-6-1-on-screen-crt/9 to place in /share/system/configs/retroarch
For example my megadrive.cfg file

aspect_ratio_index = "23"
custom_viewport_width = "1792"
custom_viewport_height = "224"
custom_viewport_x = "104"
custom_viewport_y = "16"

the last 4 lines must be adapted according to the geometry of your screen. It is possible to find the values by adjusting from the retroarch menu.

et si c'est l'anglais le soucis ... ya google trad ou encore deepL

Parfois on se demande à quoi ça sert de s'embêter à faire de la doc, si les gens lisent pas!

Par ailleurs ce serait sympa pour tout le monde de dire comment tu a réglé ton PB d'image, le partage c'est la base du forum.

[eikichi76]

Mais je mets du mien , j'ai réussi à faire fonctionné parfaitement ES en bidouillant un peu . Mais je comprenais pas pourquoi tous les jeux s'affichaient dans une colonne de quelques centimètres , genre 1/5 de l'écran .. je vais suivre à la lettre ton dernier message en espérant que cela fonctionne .. je suis pas blonde pourtant 🤨 ! Je devrais y arrivé .
Juste une dernière question , mon raspberry est alimenté par secteur et par hdmi en même temp , sûrement à cause de la Péritel acheter sur retrocables qui est alimenté par molex et mon convertisseur hdmi > vga alimenté lui aussi par secteur , c'est pas dangereux pour le matériel ?

[eikichi76]

Bon j'abandonne , j'ai suivi à la lettre tous les tuto imaginable , essayer je ne sais pas combien de resolution avec les fichiers cfg ! Le résultat est toujours le même , l'image du jeux tiens sur 1/4 au centre de l'écran. Je ne sais plus quoi faire du tout. Peut-être un soucis avec la tv je ne sais pas . En tous cas merci pour votre aide

[ian57]

@eikichi76 non ce n'est pas normal. tu as quel version de rb?

[eikichi76]

Version 6.1.1

[eikichi76]

Je remonte mon sujet pour une petite question à propos des resolutions. Quand je crée mon fichier cfg avec les resolutions de chaque emulateur, pour la megadrive par exemple , quand je passe en 1920x224 , l'image sort un peu de mon écran sur les côtés, quand je passe en 1792x224 j'ai bien toute l'image, mais au détriment de petites bandes noires sur les côtés. En modifiant en jeu la résolution pour épouser parfaitement mon ecran au pixel près , ça me donne des resolutions bizarres genre 1877x224 . Comme j avais lu qu il fallait utiliser des resolutions divisibles genre 1920 , 1792 , 1680 , 1536 ex .. je préfèrerais avoir votre avis pour savoir si cela avait un impact sur les jeux ?