@vdeolive tu peux essayer en virant l'overclock ?
Recalbox 18.04.20 > Ne boote plus
-
Bonjour,
Surprise aujourd'hui, ma recalbox ne boot plus. Aussi je m'en remets à votre expertise après avoir testé plusieurs choses.
J'ai vérifié l'alim et la carte SD tout à l'air en ordre.
La LED rouge est allumée
La LED Verte ACT s'allume puis clignote ce qui me fait penser au le problème se situe plus au niveau de l'accès aux fichiers
Sur la partition Boot j'ai bien les fichiers/overlays
/System Volume Information
.keep
bcm2710-rpi3-b.dtb
bootcode.bin
cmdline.txt
config.txt
fixup.dat
recalbox-boot.conf
start.elf
zImageLe fichier cmdline.txt donne :
dwc_otg.fiq_fix_enable=1 sdhci-bcm2708.sync_after_dma=0 dwc_otg.lpm_enable=0 console=tty3 consoleblank=0 loglevel=3 elevator=deadline vt.global_cursor_default=0 logo.nologo root=/dev/mmcblk0p2 rootwait fastboot noswap roLe fichier config.txt donne :
uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1
disable_overscan=1uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1comment to get jack audio
hdmi_drive=2
Using /etc/modules is deprecated and no longer supported on 4.4 kernel
So manually enable audio
dtparam=audio=on
config_hdmi_boost=1
force hdmi while the tv can take time before sending the signal on the hdmi output
hdmi_force_hotplug=1
uncomment for composite PAL
#sdtv_mode=2
uncomment for lirc-rpi
#dtoverlay=lirc-rpi
if you plug your tv at the same time as your rpi and that the rpi switches from the hdmi or give a low resolution because tv had no enough time to initialize it
boot_delay=3
uncomment if you don't want the rainbow at startup
disable_splash=1
default CEC name
cec_osd_name=recalbox
Overclock
gpu_mem_256=128
gpu_mem_512=256
gpu_mem_1024=512avoid_safe_mode=1
kernel=zImage
arm_freq=1300
core_freq=500
sdram_freq=575
force_turbo=0
over_voltage=4
over_voltage_sdram_p=6
over_voltage_sdram_i=4
over_voltage_sdram_c=4
gpu_freq=500
sdram_schmoo=0x02000020Je ne trouve pas de solution pour rebooter ma recalbox malgrés mes recherches.
Est-ce qu'une âme charitable pourrait m'aider svp?
En vous remerciant.
Cordialement
-
@vdeolive tu peux essayer en virant l'overclock ?
-
Bonjour,
J'ai supprimé l'overclock
uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1
disable_overscan=1
uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1comment to get jack audio
hdmi_drive=2
Using /etc/modules is deprecated and no longer supported on 4.4 kernel
So manually enable audio
dtparam=audio=on
config_hdmi_boost=1
force hdmi while the tv can take time before sending the signal on the hdmi output
hdmi_force_hotplug=1
uncomment for composite PAL
#sdtv_mode=2
uncomment for lirc-rpi
#dtoverlay=lirc-rpi
if you plug your tv at the same time as your rpi and that the rpi switches from the hdmi or give a low resolution because tv had no enough time to initialize it
boot_delay=3
uncomment if you don't want the rainbow at startup
disable_splash=1
default CEC name
cec_osd_name=recalbox
Overclock
gpu_mem_256=0
gpu_mem_512=0
gpu_mem_1024=0avoid_safe_mode=1
kernel=zImage
arm_freq=1200
core_freq=500
sdram_freq=575
force_turbo=0
over_voltage=4
over_voltage_sdram_p=6
over_voltage_sdram_i=4
over_voltage_sdram_c=4
gpu_freq=400
sdram_schmoo=0x02000020Ce qui me gêne c'est qu'il n'y a même pas d'écran noir sur la TV.
Rien ne passe vers la sortie HDMI
Le PI reste avec la LED rouge allumée et la verte qui clignote encore.Une autre idée svp?
En vous remerciant.
Cordialement
-
Ne seraient ce pas les fichiers start.elf ou zImage qui seraient corrompus?
Si oui, peut on en réinjecter de nouveaux?
En vous remerciant.
-
Je précise que la carte SD est une Sandisk Ultra 128Go
Class10 achetée sur amazon -
La manette bt se connecte ce qui signifie que le pi et le système fonctionnent
-
@vdeolive tu as accès en ssh ?
-
cela semble possible. La prise reseau est allumée
J'ai utilisé cyberduck avec un cable reseau relié a mon pc
je fais ouvrir une nouvelle connexion SSH avec root // recalboxroot
mais la recalbox ne renvoit pas une IP valide (169.254.189.182)
Et la connexion échoue. -
Je viens de connecter le PI a ma box ald du PC (merci le forum) et ca marche
Je suis connecté au PI par réseau \RECALBOX.
J'ai accès aux repertoires Root et Share, ce qui est une bonne nouvelle car celà veut dire que le Pi n'est pas flingué et qu'au pire je peux faire un backup de mes ROMS patiemment triées et scrappées. :).Qu'est ce que je dois modifier désormais pour retrouver un affichage HDMI svp?
En vous remerciant.
-
@vdeolive une archive de support stp. Tu n'as meme pas la vidoe d'intro ?
-
J'ai accès à tout via le réseau
tout fonctionne.En revanche le PI n'envoit pas de signal vers l'écran.
Quel archive de support veux tu?
le Recalbox.conf?System Variable
You can configure your recalbox from here
To set a variable, remove the first ; on the line
------------ A - System Options -----------
Uncomment the system.power.switch you use
;system.power.switch=ATX_RASPI_R2_6 # http://lowpowerlab.com/atxraspi/#installation
;system.power.switch=MAUSBERRY # http://mausberry-circuits.myshopify.com/pages/setup
;system.power.switch=REMOTEPIBOARD_2003 # http://www.msldigital.com/pages/support-for-remotepi-board-2013
;system.power.switch=REMOTEPIBOARD_2005 # http://www.msldigital.com/pages/support-for-remotepi-board-plus-2015
;system.power.switch=WITTYPI # http://www.uugear.com/witty-pi-realtime-clock-power-management-for-raspberry-pi
;system.power.switch=PIN56ONOFF # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)
;system.power.switch=PIN56PUSH # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)
;system.power.switch=PIN356ONOFFRESET # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)
;system.power.switch=PIN356PUSHRESET # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)fbcp FrameBuffer Copy Program
For small TFT screen on GPIO and SPI
See https://github.com/recalbox/recalbox-os/wiki/Utility---Use-of-fbcp-for-small-TFT-screen-(EN) for details
Needed for Waveshare 3.2" 3.5" TFT screen, 2.8" Adafruit screen
See https://github.com/recalbox/recalbox-os/wiki/TFT-Screen-SPI-Bus-(EN)
for support and configuration details needed by /boot/config.txt
system.fbcp.enabled=0
Recalbox Manager (http manager)
system.manager.enabled=1
1 or 2, depending on the manager version you wish
system.manager.version=2
Recalbox security
enforce security
samba password required
disable virtual gamepads
system.security.enabled=0
Recalbox API (REST)
system.api.enabled=1
Allow a specific resolution for ES only from the command : tvservice -m [MODE]
Leave commented for the default usual behaviour
;system.es.videomode=CEA 4 HDMI
EmulationStation
menu style
default -> default all options menu
none -> no menu except the game search menu
bartop -> less menu, only needed for bartops
emulationstation.menu=default
Select a system to show on boot (use rom directory name) (string)
emulationstation.selectedsystem=favorites
Show the gamelist of the first or selected system on boot (0,1)
emulationstation.bootongamelist=0
Disable system view ES will boot and show ONLY the first or selected system (0,1)
emulationstation.hidesystemview=0
Pa**e Gamelists only. Show only games listed in gamelist.xml files (0,1)
emulationstation.gamelistonly=0
Force basicgameList view to be displayed, even if your game systems are scraped (0,1)
emulationstation.forcebasicgamelistview=0
Emulator special keys
default -> default all special keys
nomenu -> cannot popup the emulator menu
none -> no special keys in emulators
system.emulators.specialkeys=default
Show or hide kodi in emulationstation (0,1)
kodi.enabled=1
Start kodi at launch (0,1)
kodi.atstartup=0
set x button shortcut (0,1)
kodi.xbutton=1
Allow a specific resolution for Kodi only from the command : tvservice -m [MODE]
By default is using the default resolution of your screen
kodi.videomode=default
Kodi can wait for a network component before starting
waithost is the ip or hostname that must answer to a ping to validate the availability
waittime is the maximum time waited when kodi boots
if waitmode is required, kodi will not start if the component is not available
if waitmode is wish, kodi will start if the component is not available
if waitmode is not set or has another value, kodi will start immediately
;kodi.network.waitmode=required
;kodi.network.waittime=10
;kodi.network.waithost=192.168.0.50Hyperion
Hyperion allows you to use an ambilight like led system on your recalbox
Use hypercon to create your configuration file, and copy it in /recalbox/share/system/configs/hyperion/hyperion.config.json
hyperion.enabled=0
------------ B - Network ------------
Set system hostname
system.hostname=RECALBOX
Activate wifi (0,1)
wifi.enabled=1
Wifi SSID (string)
wifi.ssid=Freebox-647D38
Wifi KEY (string)
after rebooting the recalbox, the "new key" is replace by a hidden value "enc:xxxxx"
you can edit the "enc:xxxxx" value to replace by a clear value, it will be updated again at the following reboot
Escape your special chars (# ; $) with a backslash : $ => $
xxxxxxxxx
secondary wifi (not configurable via the user interface)
;wifi2.ssid=new ssid
;wifi2.key=new keythird wifi (not configurable via the user interface)
;wifi3.ssid=new ssid
;wifi3.key=new keySamba share
system.samba.enabled=1
Virtual Gamepads
system.virtual-gamepads.enabled=1
SSH
system.ssh.enabled=1
------------ C - Audio ------------
Set the audio device (auto, hdmi, jack)
audio.device=auto
Set system volume (0..100)
audio.volume=97
Enable or disable system sounds in ES (0,1)
audio.bgmusic=1
-------------- D - Controllers -----------------
Enable support for standard bluetooth controllers
controllers.bluetooth.enabled=1
Please enable only one of these
-------------- D1 - PS3 Controllers ------------
##Enable PS3 controllers support
controllers.ps3.enabled=1Choose a driver between bluez, official and shanwan
bluez -> bluez 5 + kernel drivers, support official and shanwan sisaxis
official -> sixad drivers, support official and gasia sisaxis
shanwan -> shanwan drivers, support official and shanwan sisaxis
controllers.ps3.driver=bluez
------------ D2 - GPIO Controllers ------------
GPIO Controllers
enable controllers on GPIO with mk_arcarde_joystick_rpi (0,1)
controllers.gpio.enabled=0
mk_gpio arguments, map=1 for one controller, map=1,2 for 2 (map=1,map=1,2)
controllers.gpio.args=map=1,2
------------ D3 - Steam Controllers ------------
Enable steam controller service
controllers.steam.enabled=0
DB9 Controllers
Enable DB9 drivers for atari, megadrive, amiga controllers (0,1)
controllers.db9.enabled=0
db9 arguments
controllers.db9.args=map=1
Gamecon controllers
Enable gamecon controllers, for nes, snes psx (0,1)
controllers.gamecon.enabled=0
gamecon_args
controllers.gamecon.args=map=1
XGaming's XArcade Tankstik and other compatible devices
controllers.xarcade.enabled=1
------------ F - Language and keyboard ------------
Set the language of the system (fr_FR,en_US,en_GB,de_DE,pt_BR,es_ES,it_IT,eu_ES,tr_TR,zh_CN)
system.language=fr_FR
set the keyboard layout (fr,en,de,us,es)
system.kblayout=us
Set you local time
Select your timezone from : ls /usr/share/zoneinfo/ (string)
system.timezone=Europe/Paris
------------ G - UPDATES ------------
Automatically check for updates at start (0,1)
updates.enabled=1
Update type : default to stable
updates.type=stable
------------ H - HERE IT IS - GLOBAL EMULATOR CONFIGURATION ------------
The global value will be used for all emulators, except if the value
is redefined in the emulator
Set game resolution for emulators
select your mode from the command : tvservice -m [MODE]
CEA 5 HDMI : 1920x1080 @ 60Hz 16:9, clock:74MHz interlaced
CEA 4 HDMI : 1280x720 @ 60Hz 16:9, clock:74MHz progressive
use 'default' for using the default resolution
use 'auto' : switches to CEA 4 HDMI if supported, else keep the current resolution
(string)
global.videomode=CEA 4 HDMI
Shader set
Automatically select shaders for all systems
##Â (none, retro, scanlines)
global.shaderset=noneOnce enabled, your screen will be cropped, and you will have a pixel perfect image (0,1)
global.integerscale=0
Set gpslp shader for all emulators (prefer shadersets above). Absolute path (string)
global.shaders=hq2x
Set ratio for all emulators (auto,4/3,16/9,16/10,custom)
global.ratio=16/9
Set smooth for all emulators (0,1)
global.smooth=1
Set rewind for all emulators (0,1)
global.rewind=0
Set autosave/load savestate for all emulators (0,1)
global.autosave=0
Enable retroarchievements (0,1)
Set your www.retroachievements.org username/password
Escape your special chars (# ; $) with a backslash : $ => $
global.retroachievements=1
global.retroachievements.hardcore=0
global.retroachievements.username=
global.retroachievements.password=Set retroarch input driver (auto, udev, sdl2)
If you don't have issues with your controllers, let auto
global.inputdriver=auto
If you do not want recalboxOS to generate the configuration for all emulators (string)
;global.configfile=/path/to/my/configfile.cfg
------------ I - EMULATORS CHOICES -----------
You can override the global configuration here
Here is the snes example
;snes.videomode=CEA 4 HDMI
snes.core=snes9x_next
;snes.shaders=/recalbox/share/shaders/shaders_glsl/mysnesshader.gplsp
;snes.ratio=16/9
;snes.smooth=0
;snes.rewind=1
;snes.autosave=0
snes.emulator=libretro
;snes.integerscale=0If you do not want recalboxOS to generate the configuration for the emulator :
;snes.configfile=/path/to/my/configfile.cfg
Default cores for RPi3
snes.core=snes9x_next
gba.core=mgba
mame.core=default
nes.core=defaultNeoGeo emulator
You can use pifba or a libretro core (fba2x,libretro)
neogeo.emulator=libretro
If you set libretro as neogeo.emulator, the line below sets the retroarch core (fba,imame4all)
neogeo.core=fba
N64 emulator is configured to display a screen with a 640x480 resolution (native n64 resolution)
So you must use one of these video modes (DMT 4 HDMI,CEA 1 HDMI).
If your screen is not compatible with one of these video modes, please check the recalbox's wiki.
n64.videomode=DMT 4 HDMI
If you are using a CRT screen, please change the setting above with this one :
n64.videomode=default
Dreamcast emulator
Like N64, such a CPU intensive emulator needs a small resolution
Consider DMT 4 HDMI (640480) or DMT 9 HDMI (800600). If you have a black screen on dreamcast, try DMT 9 HDMI here
dreamcast.videomode=DMT 4 HDMI
Configurations generated by Recalbox
psx.emulator=libretro
psx.core=pcsx_rearmed
psx.ratio=auto
scummvm.ratio=16/9
n64.emulator=default
prboom.emulator=libretro
scummvm.emulator=default
n64.core=default
nes.emulator=default
pcenginecd.emulator=default
mame.emulator=default
megadrive.emulator=default
segacd.emulator=libretro
segacd.core=genesisplusgx
prboom.core=prboom -
@vdeolive pitié ne pas mettre de copier/coller de fichiers de config ... Tu vas sur http://recalbox/help tu génères l'archive de support et tu me donnes le lien produit
-
-
Désolé. Voici l'archive support.
Merci pour ton aide -
J'ai bidouillé tout ce que j'ai pu mais rien a changer.
Le Pi ne renvoie toujours pas d'image vers la sortie HDMI.Une autre idée svp?
-
@vdeolive vire l'overclock
-
Bonjour,
J'ai supprimé toute la partie overclock du fichier Config.txt sur la carte SD.
Rien n'y fait, il n'y a toujours rien à l'écran malheureusement.Une autre idée stp?
En te remerciant
-
Le PI semble fonctionner c'est juste qu'il n'affiche rien sur la sortie HDMI.
Avant lorsque l'on allumait, le PI envoyait un signal a la TV et prenait le contrôle de l'affichage même sans selectionner la chaine source sur HDMI 1
Aujourd'hui c'est plus le cas. Plus de son plus d'image. -
@vdeolive tu as testé sur quels écrans ? Parce qu'effectivement le Pi ne trouve pas d'écran
-
Sur mes 2 TVs sur lesquelles je joue habituellement.
Une samsung 49'' et une LG 22".