Bouton ON / OFF / Reboot

antipode-x-alex

Salutations à tous, je vous contacte car j'aurais besoins d'aide sur un script ! J'achetais ce matériel qui permet d'avoir un bouton "on off reboot" : * https://github.com/LowPowerLab/ATX-Raspi Mais probleme le script ne marche pas sur recalbox, du coup si vous avez une idée ? En retirant tous les sudo le script passe sauf qu'il ne trouve pas le dossier /etc/rc.local

echo '#!/bin/bash

#This is GPIO 7 (pin 26 on the pinout diagram).
#This is an input from ATXRaspi to the Pi.
#When button is held for ~3 seconds, this pin will become HIGH signalling to this script to poweroff the Pi.
SHUTDOWN=7
REBOOTPULSEMINIMUM=200      #reboot pulse signal should be at least this long
REBOOTPULSEMAXIMUM=600      #reboot pulse signal should be at most this long
echo "$SHUTDOWN" > /sys/class/gpio/export
echo "in" > /sys/class/gpio/gpio$SHUTDOWN/direction

#Added reboot feature (with ATXRaspi R2.6 (or ATXRaspi 2.5 with blue dot on chip)
#Hold ATXRaspi button for at least 500ms but no more than 2000ms and a reboot HIGH pulse of 500ms length will be issued

#This is GPIO 8 (pin 24 on the pinout diagram).
#This is an output from Pi to ATXRaspi and signals that the Pi has booted.
#This pin is asserted HIGH as soon as this script runs (by writing "1" to /sys/class/gpio/gpio8/value)
BOOT=8
echo "$BOOT" > /sys/class/gpio/export
echo "out" > /sys/class/gpio/gpio$BOOT/direction
echo "1" > /sys/class/gpio/gpio$BOOT/value

echo "ATXRaspi shutdown script started: asserted pins ($SHUTDOWN=input,LOW; $BOOT=output,HIGH). Waiting for GPIO$SHUTDOWN to become HIGH..."

#This loop continuously checks if the shutdown button was pressed on ATXRaspi (GPIO7 to become HIGH), and issues a shutdown when that happens.
#It sleeps as long as that has not happened.
while [ 1 ]; do
  shutdownSignal=$(cat /sys/class/gpio/gpio$SHUTDOWN/value)
  if [ $shutdownSignal = 0 ]; then
    /bin/sleep 0.2
  else  
    pulseStart=$(date +%s%N | cut -b1-13) # mark the time when Shutoff signal went HIGH (milliseconds since epoch)
    while [ $shutdownSignal = 1 ]; do
      /bin/sleep 0.02
      if [ $(($(date +%s%N | cut -b1-13)-$pulseStart)) -gt $REBOOTPULSEMAXIMUM ]; then
        echo "ATXRaspi triggered a shutdown signal, halting Rpi ... "
        sudo poweroff
        exit
      fi
      shutdownSignal=$(cat /sys/class/gpio/gpio$SHUTDOWN/value)
    done
    #pulse went LOW, check if it was long enough, and trigger reboot
    if [ $(($(date +%s%N | cut -b1-13)-$pulseStart)) -gt $REBOOTPULSEMINIMUM ]; then 
      echo "ATXRaspi triggered a reboot signal, recycling Rpi ... "
      sudo reboot
      exit
    fi
  fi
done' > /etc/shutdowncheck.sh
sudo chmod 755 /etc/shutdowncheck.sh
sudo sed -i '$ i /etc/shutdowncheck.sh &' /etc/rc.local

acris

Bonjour /etc/rc.localn'existe pas sous recalbox. essaie en plaçant ton script au démarrage du pc dans /etc/init.d/ Lire : https://github.com/digitalLumberjack/recalbox-os/wiki/Ajouter-votre-propre-script-au-demarrage-(FR)

antipode-x-alex

Merci l'ami, j'essaie sa ce soir.

colwyn1978

Moi j'ai juste connecté un bouton (le même que sur les bornes d'arcade) sur 2 pins du gpio et je peux allumer sans problème et rebooter mon pi2. Pour l’éteindre je le fais par le menu, c'est bien plus simple et aucun besoin de trifouiller dans des lignes de codes.

antipode-x-alex

Bon pas reussis mais j'abandonne pas... Error :

ATXRaspi shutdown script started: asserted pins (7=input,LOW; 8=output,HIGH). Waiting for GPIO7 to become HIGH...
sleep: invalid number '0.02'
/etc/init.d/shutdowncheck.sh: line 35: 1427321809%N-1427321809%N: division by 0 (error token is "N-1427321809%N")

acris

Bonjour J'ai modifié la fin de ton script et j'ai ajouté un script pour que ça tourne en "service" je ne sais pas si ça te sera utile. J'ai supprimé aussi la commande sudo car tu es déjà en root dans recalbox J'ai supprimé la derniere ligne du sed ne sachant pas vraiement à quoi elle sert. essaie ceci : shutdowncheck.sh

echo '#!/bin/bash

#This is GPIO 7 (pin 26 on the pinout diagram).
#This is an input from ATXRaspi to the Pi.
#When button is held for ~3 seconds, this pin will become HIGH signalling to this script to poweroff the Pi.
SHUTDOWN=7
REBOOTPULSEMINIMUM=200      #reboot pulse signal should be at least this long
REBOOTPULSEMAXIMUM=600      #reboot pulse signal should be at most this long
echo "$SHUTDOWN" > /sys/class/gpio/export
echo "in" > /sys/class/gpio/gpio$SHUTDOWN/direction

#Added reboot feature (with ATXRaspi R2.6 (or ATXRaspi 2.5 with blue dot on chip)
#Hold ATXRaspi button for at least 500ms but no more than 2000ms and a reboot HIGH pulse of 500ms length will be issued

#This is GPIO 8 (pin 24 on the pinout diagram).
#This is an output from Pi to ATXRaspi and signals that the Pi has booted.
#This pin is asserted HIGH as soon as this script runs (by writing "1" to /sys/class/gpio/gpio8/value)
BOOT=8
echo "$BOOT" > /sys/class/gpio/export
echo "out" > /sys/class/gpio/gpio$BOOT/direction
echo "1" > /sys/class/gpio/gpio$BOOT/value

echo "ATXRaspi shutdown script started: asserted pins ($SHUTDOWN=input,LOW; $BOOT=output,HIGH). Waiting for GPIO$SHUTDOWN to become HIGH..."

#This loop continuously checks if the shutdown button was pressed on ATXRaspi (GPIO7 to become HIGH), and issues a shutdown when that happens.
#It sleeps as long as that has not happened.
while [ 1 ]; do
  shutdownSignal=$(cat /sys/class/gpio/gpio$SHUTDOWN/value)
  if [ $shutdownSignal = 0 ]; then
    /bin/sleep 0.2
  else  
    pulseStart=$(date +%s%N | cut -b1-13) # mark the time when Shutoff signal went HIGH (milliseconds since epoch)
    while [ $shutdownSignal = 1 ]; do
      /bin/sleep 0.02
      if [ $(($(date +%s%N | cut -b1-13)-$pulseStart)) -gt $REBOOTPULSEMAXIMUM ]; then
        echo "ATXRaspi triggered a shutdown signal, halting Rpi ... "
        poweroff
        exit
      fi
      shutdownSignal=$(cat /sys/class/gpio/gpio$SHUTDOWN/value)
    done
    #pulse went LOW, check if it was long enough, and trigger reboot
    if [ $(($(date +%s%N | cut -b1-13)-$pulseStart)) -gt $REBOOTPULSEMINIMUM ]; then 
      echo "ATXRaspi triggered a reboot signal, recycling Rpi ... "
      reboot
      exit
    fi
  fi
done' > /recalbox/scripts/shutdowncheck.sh
chmod 775 /recalbox/scripts/shutdowncheck.sh

Création du service à nommer S92shutdownService et à placer dans /etc/init.d/

#!/bin/bash
### BEGIN INIT INFO
# Provides: shutdowncheck.sh
# Required-Start: $network $local_fs $remote_fs
# Required-Stop: $network $local_fs $remote_fs
# Default-Start: 2 3 4 5
# Default-Stop: 0 1 6
# Short-Description: switch init script.
# Description: Starts and stops shutdowndeamon service.
### END INIT INFO

#VAR
RUN="/recalbox/scripts/shutdowncheck.sh"
BTD_PID=$(ps -eo pid,command | grep "/bin/bash $RUN" | grep -v grep | awk '{print $1}')

serviceStatus() {
   if [ ! -z "$BTD_PID" ]; then
      echo -e '33[0mservice shutdowncheck.sh ['$BTD_PID'] [33[33;32m OK 33[0m]'
   else
      echo -e '33[0mservice shutdowncheck.sh [33[33;31m KO 33[0m]'
   fi
}

# Carry out specific functions when asked to by the system
case "$1" in
   start)
      echo "Starting script $RUN ..."
      if [ -z "$BTD_PID" ]; then
         nice -n 19 $RUN&

         if [ $? -eq 0 ]; then
            echo -e "33[0mscript $RUN [33[33;32m STARTED 33[0m]"
         fi
      else
         echo "script $RUN already started ['$BTD_PID']!"
      fi
      #serviceStatus
   ;;
   stop)
      echo "Stopping script $RUN ..."
      if [ ! -z "$BTD_PID" ]; then
         kill $BTD_PID

         if [ $? -eq 0 ]; then
            echo -e "33[0mscript $RUN [33[33;31m STOPPED 33[0m]"
         fi
      fi
      #serviceStatus
   ;;
   status)
      serviceStatus
   ;;
   *)
      echo "Usage: /etc/init.d/S92shutdownService {start | stop | status}"
      exit 1
   ;;
esac

exit 0

chmod 777 /etc/init.d/S92shutdownService Ensuite tester :

/etc/init.d/S92shutdownService start
/etc/init.d/S92shutdownService stop
/etc/init.d/S92shutdownService status

Tiens nous au courant

mth-richer

Bonjour, Du coup cette méthode fonctionne correctement ? Merci.

antipode-x-alex

Désolé j'ai pas eu le temps de tester, j'ai refait entièrement ma salle à manger et cuisine. N'était plutôt hard que soft lol. Je mis remet cet semaine je pense.

mth-richer

Bonjour, D'accord bah tiens nous au courant dès que tu as fait ça. de mon côté si j'ai le temps je vais essayé aussi. Merci.

antipode-x-alex

Salut Acris encore desole du temp de reponse, gros travaux chez moi... Donc je viens de faire laisser cela marche tres bien juste une corrections dans ton script .

Tu as mis : done' > /recalbox/script/shutdowncheck.sh chmod 755 /recalbox/script/shutdowncheck.sh Et il fallait : done' > /recalbox/scripts/shutdowncheck.sh chmod 755 /recalbox/scripts/shutdowncheck.sh

De plus le shutdown ne se fait pas à 3 seconde mais à 7 et le reboot à 8 ! Bizarre je regarderais plus tard.

acris

Bonjour dans le script il est noté en haut : et si j ai bien compris le reboot se fait entre 3 et 10 secondes non ?

#When button is held for ~3 seconds, this pin will become HIGH signalling to this script to poweroff the Pi.
SHUTDOWN=7
REBOOTPULSEMINIMUM=200      #reboot pulse signal should be at least this long
REBOOTPULSEMAXIMUM=600      #reboot pulse signal should be at most this long
echo "$SHUTDOWN" > /sys/class/gpio/export
echo "in" > /sys/class/gpio/gpio$SHUTDOWN/direction

Pour les autres, j ai uploadé les scripts Via putty in SSH : login (root) / password (recalboxroot)

wget https://app.box.com/s/79104q7bwlzdvgjt1fjlsf9h7ktmsp3g
bash setup.sh
wget https://app.box.com/s/uz3sp9ya0ls2e6w825w26slpspeqno0m
cp ~/S92shutdownService  /etc/init.d/
chmod 775 /etc/init.d/S92shutdownService
reboot

betobcampos

<pre id="tw-target-text" class="tw-data-text vk_txt tw-ta tw-text-small" dir="ltr" style="unicode-bidi: isolate; font-family: inherit; border: none; padding: 0px 0.14em 0px 0px; position: relative; margin-top: 0px; margin-bottom: 0px; resize: none; overflow: hidden; width: 237.5px; white-space: pre-wrap; word-wrap: break-word; color: #212121; height: 288px;" data-placeholder="Tradução" data-fulltext=""><span lang="en">Hello personal , okay ? Unfortunately i do not speak French . Me parece que managed you create script To turn the rasp . Could provide OS Files paragraph download? I could not understand abcos**tamente Nothing Francisca . Thank you and sorry for the inconvenience . Beto .</span>

Bouton ON / OFF / Reboot

Want to support us ?

70
Online

99.6k
Users

28.1k
Topics

187.1k
Posts

Bouton ON / OFF / Reboot

Want to support us ?

70Online

99.6kUsers

28.1kTopics

187.1kPosts

70
Online

99.6k
Users

28.1k
Topics

187.1k
Posts