Testers wanted: major system upgrade (Pi3b+, KODI 17 and much more ...)

[crash2393]

Hello. I'm new.

I offer my best help to test image throughly, however i would need image for XU4 board. Probably i could build one from repos on my own, but it could bias the tests with bugs of my own compilation origin.

I work professionally with embeded linux systems so i hope i could contribute to great work recalbox is.

[Gaetan]

Hi @crash2393, any help is welcome
Do you own a rpi3b too ?

[crash2393]

Unfortunately no, just XU4 and quite a few A10 and A20 based SoC's but they're kinda useless for retrogaming.

[chadi]

@fry_4tf1v Thank You!!!

[Neibaf41]

Bonjour,

Installation de la beta 2 sur mon rpi3b+
Mes manettes Xbox 360 Wireless sont reconnues mais aucunes roms ne se lancent (testé SNES, CPC).
Merci et bravo pour votre travail

---

Hi,
Beta2 on my rpi3b+
Wireless Xbox 360 pad work fine but any roms boot (tested on SNES and CPC roms).
Thanks and congrats for your job

[olivierdroid92]

@Fabien-Dugué
Try to map again your pad before.
Tu dois remapper tes pads avant de joueur

[Gaetan]

@fabien-dugué you need to remap your controller first.
@olivierdroid92 ce n'est pas possible de t'envoyer un mp, tu pourrais m'en envoyer un ?
Ce serait a propos d'un test pi3b/pi3b+

[Neibaf41]

@olivierdroid92 said in Testers wanted: major system upgrade (Pi3b+, KODI 17 and much more ...):

@Fabien-Dugué
Try to map again your pad before.
Tu dois remapper tes pads avant de joueur

Merci, c'est nickel

[lafureur]

Hello, there is no valid download link ... Can you help me?

[Fry_4TF1V]

@lafureur Look my post above

[Franc-Boisier]

@fry_4tf1v Thank you !

[wally007uk]

@fry_4tf1v I used your download, when loaded up it wanted to update, did update and get lighting bolt now

[Franc-Boisier]

@wally007uk

Did U edit your recalbox.conf and set updates.type to:

https://review-507-b*mp-b-0jn0c0-archive-review-prod.recalbox.com

?

[wally007uk]

@franc-boisier said in Testers wanted: major system upgrade (Pi3b+, KODI 17 and much more ...):

https://review-507-b*mp-b-0jn0c0-archive-review-prod.recalbox.com

Yes, all that was good, when i try and run Mario Kart 64 it just goes back to game list!?

[Gaetan]

@wally007uk you need to remap your controller

[Franc-Boisier]

Hi all,

My pads are recognized, but when i launch a game, they are no longer ...
I must restart RB ...

I've tryed to reinstal, but it's always the same .

[Gaetan]

@franc-boisier Did you remap your controller ?

[Franc-Boisier]

@gaetan Yes, of course .

[VoSed]

Hello. Yesterday I installed the beta version of Recalbox, following the instructions. After some time of use, it happened strange - after clicking on "Update Game List" EmulationStation is closed. After that, I checked the file system, and it turned out that there were errors on the root partition (probably because when Recalbox hung during the transfer of games through Recalbox Manager, I turned off the RP3 from the socket). After fsck -fy, the file system errors were fixed, and I decided to install the update (root.tar.xz) again. But the problem with closing the EmultationStation was not solved. Can I solve this problem without reinstalling Recalbox?

[VoSed]

Maybe I need to unzip/untar root.tar.xz to root directory?