The Controller now Works

also i have connected the second one´.

And Yes i only use N64 Controller, as that is the main thing i want to use.

But the buttons dosent work as the buttons thei should. i found out which button is whitch one with jstest but where can i give them in at muppen64 plus.

as shown in the manual:

3.2 Testing the pads

See Test your joystick with jstest mini how-to
3.3 Calibrating the axis of N64 analog pad

jscal -s 4,1,0,0,0,6972137,6972137,1,0,0,0,6547006,6468127,1,0,0,0,536854528,536854528,1,0,0,0,536854528,536854528 /dev/input/jsX

for each N64 controller

so i Think i have to put it in the config file or somwhrer but i dont know exactly

Link to the manual

I did it.

It was just a stupid failur the ground and power pin was switched.

stupid me

but there is one final question:

Where do i have to input the folloing?:
jscal -s 4,1,0,0,0,6972137,6972137,1,0,0,0,6547006,6468127,1,0,0,0,536854528,536854528,1,0,0,0,536854528,536854528 /dev/input/jsX

jsX is the numer of controller, or is it? but where to add these lines

now i have tested the connection (maybe i dit somthing wrong with wireing)
but no all lines are working.
also i have installed version recalbox 4.0.0-beta4 and edited the config file as u sugested subs but that also didnt helpd.
is there somone that got it to work? so i can test the image on my system?

with hope BA

Thanx Subs for your help.

I have tried it as you said but still no connection.

with both lines (0,0,6,0,0 and 0,0,6,0) but nothing workd so far.

also with 0,6,0,0 and the data pin on pin 5.

maybe the gamecon driver dosent work but i have no idea how to test it

Hello Volks,

as noticed above i try to connect a n64 controller with GPIO on a Raspberry. Schamefull nothing happens.
My build in short words:
Raspberry pi 3 with original power (2,5A)
N64 controller (original not with USB)
recalbox 4.0.0-beta5

the edited recalbox.conf (edited with n++ )

Gamecon controllers

Enable gamecon controllers, for nes, snes psx (0,1)

controllers.gamecon.enabled=1

gamecon_args

controllers.gamecon.args=map=0,6,0,0

Data pin is Pin #2
Pinconection:

now when i try to move the joystick or push the buttons nothing happens, also tested with jstest.

i tried sevrel pin connections, all from the manual.
i hope some of you have a idee what i am doing wrong

P.S. The Controller is tested with the console from a friend of mine.

Sry for the bad english

Hy Leute,

wie oben beschrieben versuche ich den N64 Controller per GPIO anschließen. Leider wird nichts erkannt.
Kurz zu meinem aufbau:
Raspberry pi 3 mit original Netzteil (2,5A)
N64 controller (original nicht mit USB)
recalbox 4.0.0-beta5

meine angepasste recalbox.conf (mit n++ angepasst)

## Gamecon controllers
## Enable gamecon controllers, for nes, snes psx (0,1) 
controllers.gamecon.enabled=1
## gamecon_args
controllers.gamecon.args=map=0,6,0,0

daten pin ist pin 2

wen ich jetzt versuche den controller mit jstest zu testen bekomme ich keine veränderung.

hab schon alle pins versucht die belegt sein könnten laut anleitung.
hoffe von euch hat jemand ne idee wo ich den fehler habe

P.S. controller habe ich bei einem freund getestet er hat noch einen n64.