Recalbox 18.04.20 > Ne boote plus



  • Bonjour,

    Surprise aujourd'hui, ma recalbox ne boot plus. Aussi je m'en remets à votre expertise après avoir testé plusieurs choses.

    J'ai vérifié l'alim et la carte SD tout à l'air en ordre.
    La LED rouge est allumée
    La LED Verte ACT s'allume puis clignote ce qui me fait penser au le problème se situe plus au niveau de l'accès aux fichiers
    Sur la partition Boot j'ai bien les fichiers

    /overlays
    /System Volume Information
    .keep
    bcm2710-rpi3-b.dtb
    bootcode.bin
    cmdline.txt
    config.txt
    fixup.dat
    recalbox-boot.conf
    start.elf
    zImage

    Le fichier cmdline.txt donne :
    dwc_otg.fiq_fix_enable=1 sdhci-bcm2708.sync_after_dma=0 dwc_otg.lpm_enable=0 console=tty3 consoleblank=0 loglevel=3 elevator=deadline vt.global_cursor_default=0 logo.nologo root=/dev/mmcblk0p2 rootwait fastboot noswap ro

    Le fichier config.txt donne :

    uncomment if you get no picture on HDMI for a default "safe" mode

    #hdmi_safe=1
    disable_overscan=1

    uncomment to force a specific HDMI mode (this will force VGA)

    #hdmi_group=1
    #hdmi_mode=1

    comment to get jack audio

    hdmi_drive=2

    Using /etc/modules is deprecated and no longer supported on 4.4 kernel

    So manually enable audio

    dtparam=audio=on

    config_hdmi_boost=1

    force hdmi while the tv can take time before sending the signal on the hdmi output

    hdmi_force_hotplug=1

    uncomment for composite PAL

    #sdtv_mode=2

    uncomment for lirc-rpi

    #dtoverlay=lirc-rpi

    if you plug your tv at the same time as your rpi and that the rpi switches from the hdmi or give a low resolution because tv had no enough time to initialize it

    boot_delay=3

    uncomment if you don't want the rainbow at startup

    disable_splash=1

    default CEC name

    cec_osd_name=recalbox

    Overclock

    gpu_mem_256=128
    gpu_mem_512=256
    gpu_mem_1024=512

    avoid_safe_mode=1

    kernel=zImage
    arm_freq=1300
    core_freq=500
    sdram_freq=575
    force_turbo=0
    over_voltage=4
    over_voltage_sdram_p=6
    over_voltage_sdram_i=4
    over_voltage_sdram_c=4
    gpu_freq=500
    sdram_schmoo=0x02000020

    Je ne trouve pas de solution pour rebooter ma recalbox malgrés mes recherches.

    Est-ce qu'une âme charitable pourrait m'aider svp?

    En vous remerciant.

    Cordialement



  • @vdeolive tu peux essayer en virant l'overclock ?



  • Bonjour,

    J'ai supprimé l'overclock

    uncomment if you get no picture on HDMI for a default "safe" mode

    #hdmi_safe=1

    disable_overscan=1

    uncomment to force a specific HDMI mode (this will force VGA)

    #hdmi_group=1
    #hdmi_mode=1

    comment to get jack audio

    hdmi_drive=2

    Using /etc/modules is deprecated and no longer supported on 4.4 kernel

    So manually enable audio

    dtparam=audio=on

    config_hdmi_boost=1

    force hdmi while the tv can take time before sending the signal on the hdmi output

    hdmi_force_hotplug=1

    uncomment for composite PAL

    #sdtv_mode=2

    uncomment for lirc-rpi

    #dtoverlay=lirc-rpi

    if you plug your tv at the same time as your rpi and that the rpi switches from the hdmi or give a low resolution because tv had no enough time to initialize it

    boot_delay=3

    uncomment if you don't want the rainbow at startup

    disable_splash=1

    default CEC name

    cec_osd_name=recalbox

    Overclock

    gpu_mem_256=0
    gpu_mem_512=0
    gpu_mem_1024=0

    avoid_safe_mode=1

    kernel=zImage
    arm_freq=1200
    core_freq=500
    sdram_freq=575
    force_turbo=0
    over_voltage=4
    over_voltage_sdram_p=6
    over_voltage_sdram_i=4
    over_voltage_sdram_c=4
    gpu_freq=400
    sdram_schmoo=0x02000020

    Ce qui me gêne c'est qu'il n'y a même pas d'écran noir sur la TV.
    Rien ne passe vers la sortie HDMI
    Le PI reste avec la LED rouge allumée et la verte qui clignote encore.

    Une autre idée svp?

    En vous remerciant.

    Cordialement



  • Ne seraient ce pas les fichiers start.elf ou zImage qui seraient corrompus?

    Si oui, peut on en réinjecter de nouveaux?

    En vous remerciant.



  • Je précise que la carte SD est une Sandisk Ultra 128Go
    Class10 achetée sur amazon



  • La manette bt se connecte ce qui signifie que le pi et le système fonctionnent



  • @vdeolive tu as accès en ssh ?



  • cela semble possible. La prise reseau est allumée
    J'ai utilisé cyberduck avec un cable reseau relié a mon pc
    je fais ouvrir une nouvelle connexion SSH avec root // recalboxroot
    mais la recalbox ne renvoit pas une IP valide (169.254.189.182)
    Et la connexion échoue.



  • Je viens de connecter le PI a ma box ald du PC (merci le forum) et ca marche
    Je suis connecté au PI par réseau \RECALBOX.
    J'ai accès aux repertoires Root et Share, ce qui est une bonne nouvelle car celà veut dire que le Pi n'est pas flingué et qu'au pire je peux faire un backup de mes ROMS patiemment triées et scrappées. :).

    Qu'est ce que je dois modifier désormais pour retrouver un affichage HDMI svp?

    En vous remerciant.



  • @vdeolive une archive de support stp. Tu n'as meme pas la vidoe d'intro ?



  • J'ai accès à tout via le réseau
    tout fonctionne.

    En revanche le PI n'envoit pas de signal vers l'écran.

    Quel archive de support veux tu?
    le Recalbox.conf?

    System Variable

    You can configure your recalbox from here

    To set a variable, remove the first ; on the line

    ------------ A - System Options -----------

    Uncomment the system.power.switch you use

    ;system.power.switch=ATX_RASPI_R2_6 # http://lowpowerlab.com/atxraspi/#installation
    ;system.power.switch=MAUSBERRY # http://mausberry-circuits.myshopify.com/pages/setup
    ;system.power.switch=REMOTEPIBOARD_2003 # http://www.msldigital.com/pages/support-for-remotepi-board-2013
    ;system.power.switch=REMOTEPIBOARD_2005 # http://www.msldigital.com/pages/support-for-remotepi-board-plus-2015
    ;system.power.switch=WITTYPI # http://www.uugear.com/witty-pi-realtime-clock-power-management-for-raspberry-pi
    ;system.power.switch=PIN56ONOFF # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)
    ;system.power.switch=PIN56PUSH # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)
    ;system.power.switch=PIN356ONOFFRESET # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)
    ;system.power.switch=PIN356PUSHRESET # https://github.com/recalbox/recalbox-os/wiki/Add-a-start-stop-button-to-your-recalbox-(EN)

    fbcp FrameBuffer Copy Program

    For small TFT screen on GPIO and SPI

    See https://github.com/recalbox/recalbox-os/wiki/Utility---Use-of-fbcp-for-small-TFT-screen-%28EN%29 for details

    Needed for Waveshare 3.2" 3.5" TFT screen, 2.8" Adafruit screen

    See https://github.com/recalbox/recalbox-os/wiki/TFT-Screen-SPI-Bus-(EN)

    for support and configuration details needed by /boot/config.txt

    system.fbcp.enabled=0

    Recalbox Manager (http manager)

    system.manager.enabled=1

    1 or 2, depending on the manager version you wish

    system.manager.version=2

    Recalbox security

    enforce security

    samba password required

    disable virtual gamepads

    system.security.enabled=0

    Recalbox API (REST)

    system.api.enabled=1

    Allow a specific resolution for ES only from the command : tvservice -m [MODE]

    Leave commented for the default usual behaviour

    ;system.es.videomode=CEA 4 HDMI

    EmulationStation

    menu style

    default -> default all options menu

    none -> no menu except the game search menu

    bartop -> less menu, only needed for bartops

    emulationstation.menu=default

    Select a system to show on boot (use rom directory name) (string)

    emulationstation.selectedsystem=favorites

    Show the gamelist of the first or selected system on boot (0,1)

    emulationstation.bootongamelist=0

    Disable system view ES will boot and show ONLY the first or selected system (0,1)

    emulationstation.hidesystemview=0

    Parse Gamelists only. Show only games listed in gamelist.xml files (0,1)

    emulationstation.gamelistonly=0

    Force basicgameList view to be displayed, even if your game systems are scraped (0,1)

    emulationstation.forcebasicgamelistview=0

    Emulator special keys

    default -> default all special keys

    nomenu -> cannot popup the emulator menu

    none -> no special keys in emulators

    system.emulators.specialkeys=default

    Show or hide kodi in emulationstation (0,1)

    kodi.enabled=1

    Start kodi at launch (0,1)

    kodi.atstartup=0

    set x button shortcut (0,1)

    kodi.xbutton=1

    Allow a specific resolution for Kodi only from the command : tvservice -m [MODE]

    By default is using the default resolution of your screen

    kodi.videomode=default

    Kodi can wait for a network component before starting

    waithost is the ip or hostname that must answer to a ping to validate the availability

    waittime is the maximum time waited when kodi boots

    if waitmode is required, kodi will not start if the component is not available

    if waitmode is wish, kodi will start if the component is not available

    if waitmode is not set or has another value, kodi will start immediately

    ;kodi.network.waitmode=required
    ;kodi.network.waittime=10
    ;kodi.network.waithost=192.168.0.50

    Hyperion

    Hyperion allows you to use an ambilight like led system on your recalbox

    Use hypercon to create your configuration file, and copy it in /recalbox/share/system/configs/hyperion/hyperion.config.json

    hyperion.enabled=0

    ------------ B - Network ------------

    Set system hostname

    system.hostname=RECALBOX

    Activate wifi (0,1)

    wifi.enabled=1

    Wifi SSID (string)

    wifi.ssid=Freebox-647D38

    Wifi KEY (string)

    after rebooting the recalbox, the "new key" is replace by a hidden value "enc:xxxxx"

    you can edit the "enc:xxxxx" value to replace by a clear value, it will be updated again at the following reboot

    Escape your special chars (# ; $) with a backslash : $ => $

    xxxxxxxxx

    secondary wifi (not configurable via the user interface)

    ;wifi2.ssid=new ssid
    ;wifi2.key=new key

    third wifi (not configurable via the user interface)

    ;wifi3.ssid=new ssid
    ;wifi3.key=new key

    Samba share

    system.samba.enabled=1

    Virtual Gamepads

    system.virtual-gamepads.enabled=1

    SSH

    system.ssh.enabled=1

    ------------ C - Audio ------------

    Set the audio device (auto, hdmi, jack)

    audio.device=auto

    Set system volume (0..100)

    audio.volume=97

    Enable or disable system sounds in ES (0,1)

    audio.bgmusic=1

    -------------- D - Controllers -----------------

    Enable support for standard bluetooth controllers

    controllers.bluetooth.enabled=1

    Please enable only one of these

    -------------- D1 - PS3 Controllers ------------

    ##Enable PS3 controllers support
    controllers.ps3.enabled=1

    Choose a driver between bluez, official and shanwan

    bluez -> bluez 5 + kernel drivers, support official and shanwan sisaxis

    official -> sixad drivers, support official and gasia sisaxis

    shanwan -> shanwan drivers, support official and shanwan sisaxis

    controllers.ps3.driver=bluez

    ------------ D2 - GPIO Controllers ------------

    GPIO Controllers

    enable controllers on GPIO with mk_arcarde_joystick_rpi (0,1)

    controllers.gpio.enabled=0

    mk_gpio arguments, map=1 for one controller, map=1,2 for 2 (map=1,map=1,2)

    controllers.gpio.args=map=1,2

    ------------ D3 - Steam Controllers ------------

    Enable steam controller service

    controllers.steam.enabled=0

    DB9 Controllers

    Enable DB9 drivers for atari, megadrive, amiga controllers (0,1)

    controllers.db9.enabled=0

    db9 arguments

    controllers.db9.args=map=1

    Gamecon controllers

    Enable gamecon controllers, for nes, snes psx (0,1)

    controllers.gamecon.enabled=0

    gamecon_args

    controllers.gamecon.args=map=1

    XGaming's XArcade Tankstik and other compatible devices

    controllers.xarcade.enabled=1

    ------------ F - Language and keyboard ------------

    Set the language of the system (fr_FR,en_US,en_GB,de_DE,pt_BR,es_ES,it_IT,eu_ES,tr_TR,zh_CN)

    system.language=fr_FR

    set the keyboard layout (fr,en,de,us,es)

    system.kblayout=us

    Set you local time

    Select your timezone from : ls /usr/share/zoneinfo/ (string)

    system.timezone=Europe/Paris

    ------------ G - UPDATES ------------

    Automatically check for updates at start (0,1)

    updates.enabled=1

    Update type : default to stable

    updates.type=stable

    ------------ H - HERE IT IS - GLOBAL EMULATOR CONFIGURATION ------------

    The global value will be used for all emulators, except if the value

    is redefined in the emulator

    Set game resolution for emulators

    select your mode from the command : tvservice -m [MODE]

    CEA 5 HDMI : 1920x1080 @ 60Hz 16:9, clock:74MHz interlaced

    CEA 4 HDMI : 1280x720 @ 60Hz 16:9, clock:74MHz progressive

    use 'default' for using the default resolution

    use 'auto' : switches to CEA 4 HDMI if supported, else keep the current resolution

    (string)

    global.videomode=CEA 4 HDMI

    Shader set

    Automatically select shaders for all systems

    ## (none, retro, scanlines)
    global.shaderset=none

    Once enabled, your screen will be cropped, and you will have a pixel perfect image (0,1)

    global.integerscale=0

    Set gpslp shader for all emulators (prefer shadersets above). Absolute path (string)

    global.shaders=hq2x

    Set ratio for all emulators (auto,4/3,16/9,16/10,custom)

    global.ratio=16/9

    Set smooth for all emulators (0,1)

    global.smooth=1

    Set rewind for all emulators (0,1)

    global.rewind=0

    Set autosave/load savestate for all emulators (0,1)

    global.autosave=0

    Enable retroarchievements (0,1)

    Set your www.retroachievements.org username/password

    Escape your special chars (# ; $) with a backslash : $ => $

    global.retroachievements=1
    global.retroachievements.hardcore=0
    global.retroachievements.username=
    global.retroachievements.password=

    Set retroarch input driver (auto, udev, sdl2)

    If you don't have issues with your controllers, let auto

    global.inputdriver=auto

    If you do not want recalboxOS to generate the configuration for all emulators (string)

    ;global.configfile=/path/to/my/configfile.cfg

    ------------ I - EMULATORS CHOICES -----------

    You can override the global configuration here

    Here is the snes example

    ;snes.videomode=CEA 4 HDMI
    snes.core=snes9x_next
    ;snes.shaders=/recalbox/share/shaders/shaders_glsl/mysnesshader.gplsp
    ;snes.ratio=16/9
    ;snes.smooth=0
    ;snes.rewind=1
    ;snes.autosave=0
    snes.emulator=libretro
    ;snes.integerscale=0

    If you do not want recalboxOS to generate the configuration for the emulator :

    ;snes.configfile=/path/to/my/configfile.cfg

    Default cores for RPi3

    snes.core=snes9x_next
    gba.core=mgba
    mame.core=default
    nes.core=default

    NeoGeo emulator

    You can use pifba or a libretro core (fba2x,libretro)

    neogeo.emulator=libretro

    If you set libretro as neogeo.emulator, the line below sets the retroarch core (fba,imame4all)

    neogeo.core=fba

    N64 emulator is configured to display a screen with a 640x480 resolution (native n64 resolution)

    So you must use one of these video modes (DMT 4 HDMI,CEA 1 HDMI).

    If your screen is not compatible with one of these video modes, please check the recalbox's wiki.

    n64.videomode=DMT 4 HDMI

    If you are using a CRT screen, please change the setting above with this one :

    n64.videomode=default

    Dreamcast emulator

    Like N64, such a CPU intensive emulator needs a small resolution

    Consider DMT 4 HDMI (640480) or DMT 9 HDMI (800600). If you have a black screen on dreamcast, try DMT 9 HDMI here

    dreamcast.videomode=DMT 4 HDMI

    Configurations generated by Recalbox

    psx.emulator=libretro
    psx.core=pcsx_rearmed
    psx.ratio=auto
    scummvm.ratio=16/9
    n64.emulator=default
    prboom.emulator=libretro
    scummvm.emulator=default
    n64.core=default
    nes.emulator=default
    pcenginecd.emulator=default
    mame.emulator=default
    megadrive.emulator=default
    segacd.emulator=libretro
    segacd.core=genesisplusgx
    prboom.core=prboom



  • @vdeolive pitié ne pas mettre de copier/coller de fichiers de config ... Tu vas sur http://recalbox/help tu génères l'archive de support et tu me donnes le lien produit





  • Désolé. Voici l'archive support.
    Merci pour ton aide



  • J'ai bidouillé tout ce que j'ai pu mais rien a changer.
    Le Pi ne renvoie toujours pas d'image vers la sortie HDMI.

    Une autre idée svp?



  • @vdeolive vire l'overclock



  • Bonjour,

    J'ai supprimé toute la partie overclock du fichier Config.txt sur la carte SD.
    Rien n'y fait, il n'y a toujours rien à l'écran malheureusement.

    Une autre idée stp?

    En te remerciant



  • Le PI semble fonctionner c'est juste qu'il n'affiche rien sur la sortie HDMI.
    Avant lorsque l'on allumait, le PI envoyait un signal a la TV et prenait le contrôle de l'affichage même sans selectionner la chaine source sur HDMI 1
    Aujourd'hui c'est plus le cas. Plus de son plus d'image.



  • @vdeolive tu as testé sur quels écrans ? Parce qu'effectivement le Pi ne trouve pas d'écran



  • Sur mes 2 TVs sur lesquelles je joue habituellement.
    Une samsung 49'' et une LG 22".


Log in to reply
 

Want to support us ?

Join us on :

231
Online

31182
Users

15132
Topics

113838
Posts

Looks like your connection to Recalbox Forum was lost, please wait while we try to reconnect.