Recalbox 6.0 is OUT! Codename: Dragonblaze
@recalmanc try flashing your sd card again and wait patiently when booting up recalbox the first time until you reach ES. Otherwise partitions won’t be created properly.
@paradadf Thanks for the reply - I have done this several times. It completes and the larger drive is there; I get it loaded up with ROMS and then randomly it looses that partition and goes back to basic settings.
I'm running this on a 240gb SSD, i7 with 4GB RAM.
@recalmanc can you give me the output of
Filesystem Size Used Available Use% Mounted on
none 1.9G 0 1.9G 0% /dev
/dev/sda2 1.9G 1.6G 206.6M 89% /
tmpfs 1.9G 0 1.9G 0% /dev/shm
tmpfs 1.9G 12.0K 1.9G 0% /tmp
tmpfs 1.9G 5.1M 1.9G 0% /var
tmpfs 1.9G 300.0K 1.9G 0% /run
/dev/sda1 63.0M 10.0M 53.0M 16% /boot
/dev/sda3 217.0G 39.5G 166.5G 19% /recalbox/share
/dev/sda3 217.0G 39.5G 166.5G 19% /media/usb0
@recalmanc it looks good to me. Sadly, I don’t know what’s happening.
@recalmanc , this also happened to me several times.
I think, it may happened because you don't shutdown recalbox properly.
Do not shutdown using the PC power ON/Off button, but use software "Shutdown" in the recalbox menu instead. If you not shutdown properly, the "share" partition will not be unmounted properly, and recalbox will not be able to mount it again at the next boot because the partition will have errors.
If it happened, unplug your hard disk and plug it under a linux system, then use "fsck" command to repair the faulty partition, it worked for me.
@garmadon That makes sense as I just noticed that the "Skraper" app I was using was restarting my recalbox machine after each system was complete. I guess it doesn't shut it down correctly. I have stopped using it and I've been stable for a lot longer than I have so far.
Thank you for your help.
@paradadf No worries, I think I worked it out (see below). Thanks for trying to assist though! :)
@recalmanc , yes i think you're right. Skraper may be responsible.
It happened to me just yesterday at the end of a scrap using the same software.
Skraper reboot the whole operating system after each scrap. It should restart only "emulation station".
@garmadon :) At least I wasn't going insane :) Now all I have to do is work out how to make this all work with my x-Arcade Dual joystick and put it all in my cabinet and I'm good to go!
Thanks for everyones help.
My Wifi isn't working until I re enter the password everytime even without any special characters. Is there a solution for this?
Hello, first of all Recalbox is one of the finest thing out there.Thx for all the good work.
Is there some new informations about x86 x64_84 installation/startup issues. I used to have 18.7.13 which was great.
But I never got any update for dragonblaze, which from what I found out on this forum doesn t work. You need to install a fresh copy.
So I made a backup, at least stuff is secured. Used Balenea to install the dragonbalze on my Ssd. Installation stars at least screens shows booting recalbox. After a while the ES interface appears shows which music is playing then goes back to the black screen with booting recalbox. I waited at least 30 min but nothing happend.I am able to acces web interface from the recalbox, from there I restart ES the interface shows up a then dissapears after 5 sec again. This is the issue with x86. On the 64 version interface seems to work a bit better but when I try to pair a bluetooth controller, it also crahes the interface and I m again on the booting recalbox screen. From the webinterface I can also restart Es interface but pairing seems not to work well.
I decided to install the beta version from santa claus and febuary from the forum. The issues is exactly the same.
Cloud it be that the 6 builds version have some hardware compatibility issues?
My config is the following.
Intel Core 2 Duo E8400
Ssd 500G Adata Spx900.
Is there a way to download the 18.7.13 x86 again ?