Raspberry Pi 4

For information, Recalbox IS NOT compatible with Raspberry Pi 4 yet.
Pour information, Recalbox N'EST PAS encore compatible avec le Raspberry Pi 4.

The Recalbox Team.

February 2019 Beta Version



  • bonjour
    j ai installer la derniere beta et quand je veux lancer un jeux dreamcast , ca se bloque a la configuration de la manette que dois je faire pour contrer ce probleme ??? sinon pour la neo geo cd le bruit n est plus present


  • Global moderator
    Team

    @ViRuS-MaN reconfigure ta manette et on a pas de boule de cristal merci d etre precis.



  • J ai fait la configuration et ca fonctionne , mais je ne comprends pas ma manette etait reconnue je pouvais bouger dans les menus et lancer un jeux sur d autre systeme ca fonctionne , la j ai reconfigurer ma menette comme tu me la conseiller et ca fonctionne.
    merci



  • Bonjour !
    Merci pour le travail accompli.
    Ma config :
    Raspberry Pi 3b +
    Micro SD Sandisk 32 Go
    Config et roms sur clée USB
    recalbox.2019-02-23-beta.rpi3
    Voila mon souci ,impossible de sauvegarder mes shaders ainsi que les overlays dans retroarch .Je fais bien la sauvegarde via retroarch qui m'indique sav ok de la config puis quand je quitte le menu retroarch et que je relance une rom, il faut de nouveau reconfigurer les shaders ainsi que les overlays pour pouvoir jouer dans de bonne condition.


  • Tester

    Bonjour à tous ^^

    @Bkg2k voici les configurations pour différents pads avec la version BETA 2019.02.23 rpi3 sur un pi3b.

    La liste des pads :

    • XBOX 360 Filaire (Officiel MICROSOFT)
    • iBuffalo Classic USB Gamepad
    • 8Bitdo NES30 Arcade Stick (USB et sans fils)
    • PS4 Dualshock 4 (Officiel SONY) (USB et sans fils)
    • SNES "no name"
    • 8Bitdo SFC30 (USB et sans fils)
    • 8Bitdo SF30 PRO (USB et sans fils)

    --> Lien pastebin des configurations pad

    Le stick arcade "8Bitdo NES30" est configuré comme sur l'image en lien.

    Merci pour le travail accompli, au plaisir d'aider...

    PS : C'est normal que le pad 8Bitdo SF30 PRO utilisé directement en mode "filaire USB" soit détecté avec le nom "Microsoft X-Box 360 pad" (Ce n'est pas une erreur, j'ai vérifié plusieurs fois ^^) ?


  • Local Moderator
    Tester

    @Bkg2k
    Ordre pour appairer deux manettes BT.
    Board : RPI3B
    Image : 2019-02-24

    Y a t il un ordre pour appairer 2 manettes en Bluetooth ?
    Je suis en D-input mode (Start+B)

    Depuis une fresh installe, Micro SD uniquement, pas de WIFi, Rj-45 uniquement, pas de theme.

    Il m'est impossible d'appairer 2 manettes BT dans l'ordre suivant.
    1- Demarrage recalbox ; fresh installe
    2- Suppression de tous les liens BT
    3- reset BT manette 8bitdo SF30 Pro
    4- détection BT manette 8bitdo SF30 Pro
    5- demande de connection BT manette 8bitdo SF30 Pro = ok
    6- reset BT manette 8bitdo SN30 Pro
    7- détection BT manette 8bitdo SN30 Pro
    8- demande de connection BT manette 8bitdo SN30 Pro = impossible à appairer (cette manette se trouve en 2ieme position dans la liste)
    Dans la liste j'ai
    a) Mac SF30
    b) Mac SN30--> je clique OK ici

    Par contre en changeant l'odre ce fonctionne
    1- Demarrage recalbox ; fresh installe
    2- Suppression de tous les liens BT
    3- reset BT manette 8bitdo SN30 Pro
    4- détection BT manette 8bitdo SN30 Pro
    5- demande de connection BT manette 8bitdo SN30 Pro = ok
    6- reset BT manette 8bitdo SF30 Pro
    7- détection BT manette 8bitdo SF30 Pro
    8- demande de connection BT manette 8bitdo SF30 Pro = OK ca marche (cette manette se trouve en 1ere position dans la liste)
    a) Mac SF30 --> je clique OK ici
    b) Mac SN30

    Question : Y a t il une préférence des adresse MAC de détection BT pour appairer les manettes BT ?
    J'ai l'impression que lorsque la manette que l'on veut appairer se trouver en 2ieme position, on arrive sur "failed to pair" alors que si la 2ieme manette à appairer est lister en première position, ca fonctionne.
    Est-ce possible ?



  • @ddpiksen said in February 2019 Beta Version:

    Bonjour !
    Merci pour le travail accompli.
    Ma config :
    Raspberry Pi 3b +
    Micro SD Sandisk 32 Go
    Config et roms sur clée USB
    recalbox.2019-02-23-beta.rpi3
    Voila mon souci ,impossible de sauvegarder mes shaders ainsi que les overlays dans retroarch .Je fais bien la sauvegarde via retroarch qui m'indique sav ok de la config puis quand je quitte le menu retroarch et que je relance une rom, il faut de nouveau reconfigurer les shaders ainsi que les overlays pour pouvoir jouer dans de bonne condition.

    Hello friends! I noticed exactly the same problem. I have pretty much the same configuration except for my microSD card which has 128Gb and my roms are internal. In no one retroarch emulator I can save configurations of shaders. In the previous version (13.07.18) with R pi 3B this was possible. Thanks.



  • I'm not sure if this is a recalbox issue or hardware issue but sometimes when I restart my pi 3b+ the flash drive is no longer recognized and the internal storage is used. After reboot, it goes back to using the flash drive. Also on occasion the wifi doesn't auto connect on boot up, I have to turn wifi off and then back on. I'm also still having an off issue that even though I did a fresh install on an SD card of the latest beta and a black SD card, the 3 NES games that I tried using before won't but, all new games do boot. It's almost as if there is something residual Stoll there even after formatting. It's frustrating because the roms were working and then they just stopped. I will try a total format on next release and hopefully that fixes the issue. Also the scraper can't find certain games even thought I know they are in the database. Most likely not a recalbox problem.



  • the new beta-version is really great
    the most of all works great. i use pi3+ with 4gb sd for booting, and 128gb stick for system and roms data and a x360 controler.

    but...
    is it possible to change the dreamcast language from french to a other language?
    all eu images plays french, but i need german.
    when I go to the dreamcast menu with x + y + a + b and then start, i can select the language in the configuration, but saving is not possible - only black screen when i will start the game

    one more question:

    I use a 4:3 tube tv (for more 80s feeling) over a hdmi2av Adapter. The most emulators works great and in full screen, and its amazing. But amiga an daphne will not works perfect. black boarders left and right. Is it possible to change the aspect ratio for this emulators somehow?

    THX and THX for the hard work on Recalbox!!

    4_1551196396961_IMG_7900.jpg 3_1551196396961_IMG_7899.jpg 2_1551196396961_IMG_7897.jpg 1_1551196396961_IMG_7896.jpg 0_1551196396960_IMG_7893.jpg



  • is it possible to change the dreamcast language from french to a other language?
    all eu images plays french, thats not so good for me.
    when I go to the dreamcast menu with x + y + a + b and then start, i can select the language in the configuration, but saving is not possible - only black screen when i will start the game

    Your bios file is french. Install bios coresponding to your language of choice



  • I have tested two USB joysticks:

    	<inputConfig type="joystick" deviceName="BSGPAC02 Series" deviceGUID="03000000d81d00000e00000010010000" deviceNbAxes="4" deviceNbHats="1" deviceNbButtons="13">
    		<input name="a" type="button" id="1" value="1" code="305" />
    		<input name="b" type="button" id="0" value="1" code="304" />
    		<input name="down" type="axis" id="1" value="1" code="1" />
    		<input name="hotkey" type="button" id="8" value="1" code="312" />
    		<input name="l2" type="button" id="7" value="1" code="311" />
    		<input name="l3" type="button" id="10" value="1" code="314" />
    		<input name="left" type="axis" id="0" value="-1" code="0" />
    		<input name="pagedown" type="button" id="2" value="1" code="306" />
    		<input name="pageup" type="button" id="6" value="1" code="310" />
    		<input name="r2" type="button" id="3" value="1" code="307" />
    		<input name="r3" type="button" id="11" value="1" code="315" />
    		<input name="right" type="axis" id="0" value="1" code="0" />
    		<input name="select" type="button" id="8" value="1" code="312" />
    		<input name="start" type="button" id="9" value="1" code="313" />
    		<input name="up" type="axis" id="1" value="-1" code="1" />
    		<input name="x" type="button" id="5" value="1" code="309" />
    		<input name="y" type="button" id="4" value="1" code="308" />
    	</inputConfig>
    
    <inputConfig type="joystick" deviceName="PS3/PC Gamepad" deviceGUID="03000000100800000300000010010000" deviceNbAxes="5" deviceNbHats="1" deviceNbButtons="12">
    		<input name="a" type="button" id="2" value="1" code="290" />
    		<input name="b" type="button" id="6" value="1" code="294" />
    		<input name="down" type="axis" id="1" value="1" code="1" />
    		<input name="hotkey" type="button" id="8" value="1" code="296" />
    		<input name="l2" type="button" id="5" value="1" code="293" />
    		<input name="left" type="axis" id="0" value="-1" code="0" />
    		<input name="pagedown" type="button" id="1" value="1" code="289" />
    		<input name="pageup" type="button" id="0" value="1" code="288" />
    		<input name="r2" type="button" id="7" value="1" code="295" />
    		<input name="right" type="axis" id="0" value="1" code="0" />
    		<input name="select" type="button" id="8" value="1" code="296" />
    		<input name="start" type="button" id="9" value="1" code="297" />
    		<input name="up" type="axis" id="1" value="-1" code="1" />
    		<input name="x" type="button" id="3" value="1" code="291" />
    		<input name="y" type="button" id="4" value="1" code="292" />
    	</inputConfig> 
    

    with this last joystick, select + start doesn't exit on amiberry emulator.



  • @dh04000 is there a bios file for french and a other for german?
    I thought the bios is anyway region-free


  • Developer
    Global moderator
    Team

    @asirome Thanks for your configuration files



  • @virtualhours said in February 2019 Beta Version:

    is it possible to change the dreamcast language from french to a other language?
    all eu images plays french, but i need german.
    when I go to the dreamcast menu with x + y + a + b and then start, i can select the language in the configuration, but saving is not possible - only black screen when i will start the game

    I solved in this way:

    1. Go internal dreamcast menu (x + y + a + b and then start)
    2. Adjust date/time and select your language
    3. Erase the two memory card (Only first time)
    4. DO NOT GO back to "game", simply exit from menu with hotkey button on your pad.

    Ok. Next game start will be in your language! 😉
    If you don't want lost your save games, you can manually save files vmu_save_A1.bin and vmu_save_A2.bin from share/saves/dreamcast/reicast and restore after the above procedure.

    These are my bios:
    e10c53c2f8b90bab96ead2d368858623 dc_boot.bin
    0a93f7940c455905bea6e392dfde92a4 dc_flash.bin



  • Hello everybody!
    Today I made a fresh install of latest beta (feb 24), but can not start Kodi, after pressing launch button, immediately returned to main Recalbox screen.

    Wifi is working fine, roms are working fine. Gamepads are configured and working fine.

    With previous Beta, Kodi was working without problems.

    System:
    Rasp 3b+
    Micro SD 32gb Kingston for OS
    USB 32gb Kingston for Roms
    Generic USB gamepad PS2 style.

    Tried with the usb and without the usb.

    Edit: if I start Recalbox only with a keyboard connected, I can start Kodi. Then plugged the USB gamepad, and configured buttons inside Kodi, but when restarting only with gamepad connected, same problem: can not start Kodi.



  • @maxmoro77 said in February 2019 Beta Version:

    @virtualhours said in February 2019 Beta Version:

    is it possible to change the dreamcast language from french to a other language?
    all eu images plays french, but i need german.
    when I go to the dreamcast menu with x + y + a + b and then start, i can select the language in the configuration, but saving is not possible - only black screen when i will start the game

    I solved in this way:

    1. Go internal dreamcast menu (x + y + a + b and then start)
    2. Adjust date/time and select your language
    3. Erase the two memory card (Only first time)
    4. DO NOT GO back to "game", simply exit from menu with hotkey button on your pad.

    Ok. Next game start will be in your language! 😉
    If you don't want lost your save games, you can manually save files vmu_save_A1.bin and vmu_save_A2.bin from share/saves/dreamcast/reicast and restore after the above procedure.

    These are my bios:
    e10c53c2f8b90bab96ead2d368858623 dc_boot.bin
    0a93f7940c455905bea6e392dfde92a4 dc_flash.bin

    PERFECT! It works great! THX


  • Developer
    Global moderator
    Team

    @jorgemagana Did you remap your pad in EmulationStation?


  • Tester

    @Bkg2k @jorgemagana

    Hello sirs,

    I can confirm the bug with Kodi. After a fresh install of the last beta (2019-02-23), launching Kodi leads back to ES. Remapping the pad (Shanwan PS3 BT for me) doesn't change anything, same behavior : back to ES.

    The workaround I've found is to start Kodi by default when I turn On the Raspberry : Kodi launch automatically, I can use the PS3 pad and watch movies as usual (without remapping). When I quit Kodi, I'm back to ES and can play games, no problem with pad (no remapping needed). BUT, when I try to restart Kodi, same behavior : back to ES. I need to restart the Raspberry to reach Kodi.

    A link to a support archive done after a fresh install and the abort of Kodi's launch : https://file.ac/r7K_NgpMG9c/

    My setup for this test : RPI3B (no B+), Sandisk card, one Shanwan PS3 pad on external BT dongle, fresh install, default roms and default setup.

    The previous release did not behave this way.

    Thanks to all of the devs for all the job you do and withstand the pressure put on you.



  • @bkg2k said in February 2019 Beta Version:

    @jorgemagana Did you remap your pad in EmulationStation?

    Yes. First thing I did.



  • System: Rpi 3B+ & Sandisk 32Go & Recalbox February 2019 Bêta Version
    Stockage: clé usb sandisk 128go
    Réseau: Filaire

    Bonjour, je rencontre une difficulté avec la nouvelle Beta de février. jusqu'alors en beta de noel tout fonctionnait impec, à présent je n'arrive plus à remplir convenablement mon écran avec les jeux. Si j'effectue les mêmes réglages dans le .conf qu'auparavant, à savoir globalvideomode: default et ratio à 5/4 je me retrouve avec un écran de jeux minuscule rectangulaire au milieu...
    J'ai tenté bien des combinaisons dans le videomode et le rato..en vain. le mieux que j'obtiens c'est une bande haute et basse noire résiduel, en ratio auto.
    Merci à vous !



Want to support us ?

311
Online

77.2k
Users

19.4k
Topics

144.0k
Posts