<![CDATA[RetroTINK-Ultimates no image]]>So I bought this hat to output to vga and use some custom hdmi_timings. But I just can't get an image. At all.

I use the configuration file found here http://eightvirtues.com/?page_id=418 but I guess that was not made with vga in mind.

]]>https://forum.recalbox.com/topic/12588/retrotink-ultimates-no-imageRSS for NodeWed, 13 May 2026 00:20:44 GMTSat, 03 Feb 2018 07:10:01 GMT60<![CDATA[Reply to RetroTINK-Ultimates no image on Sun, 04 Feb 2018 12:19:05 GMT]]>@mr-karmeck the sh are made for retropie, it's gonna need quite some customisations to make them work on recalbox. If you're fine with linux, then go ahead. If not, i don't have time to spend on that.

Note that hisresolution.ini is for mame 0.184, which has quite soe differences with mame 0.78 (and probably mame 2010)

]]>https://forum.recalbox.com/post/88796https://forum.recalbox.com/post/88796Sun, 04 Feb 2018 12:19:05 GMT<![CDATA[Reply to RetroTINK-Ultimates no image on Sun, 04 Feb 2018 10:42:31 GMT]]>And we have progress. Mike Chi mailed me back with a working config file. Now hdmi timings it came with was out of range for me so I used

hdmi_timings=2048 1 180 202 300 240 1 3 5 14 0 0 0 120 0 85909090 1

From his website.

Now I have thees sh files found here https://drive.google.com/drive/folders/0B8uZtHByEHyBMkNRRmk4T2E1ZUk to make emulation not stretch so much. Were do I put them to have the same effect as with retropie.
hdmi_timings=450 1 50 30 90 270 1 1 1 30 0 0 0 50 0 9600000 1
display_rotate=0

audio_pwm_mode=2
disable_audio_dither=1

disable_overscan=1

hdmi_drive=2

config_hdmi_boost=0

hdmi_force_hotplug=1

boot_delay=3

disable_splash=1

Overclock

gpu_mem_256=128
gpu_mem_512=256
gpu_mem_1024=512

avoid_safe_mode=1

dtoverlay=pi3-disable-bt-overlay

dtparam=audio=on
#dtoverlay=pwm-2chan,pin=18,func=2,pin2=19,func2=2

dtoverlay=dpi24
enable_dpi_lcd=1
display_default_lcd=1
dpi_output_format=519
dpi_group=2
dpi_mode=87

kernel=zImage
overscan_scale=0
�����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������

]]>https://forum.recalbox.com/post/88788https://forum.recalbox.com/post/88788Sun, 04 Feb 2018 10:42:31 GMT<![CDATA[Reply to RetroTINK-Ultimates no image on Sat, 03 Feb 2018 10:43:27 GMT]]>Using the lakka img I do get image, 120hz 240p also working. So nothing wrong on the hardware side.

]]>https://forum.recalbox.com/post/88673https://forum.recalbox.com/post/88673Sat, 03 Feb 2018 10:43:27 GMT<![CDATA[Reply to RetroTINK-Ultimates no image on Sat, 03 Feb 2018 10:08:28 GMT]]>I'm now trying the pre made lakka img to know everything is working.

]]>https://forum.recalbox.com/post/88669https://forum.recalbox.com/post/88669Sat, 03 Feb 2018 10:08:28 GMT<![CDATA[Reply to RetroTINK-Ultimates no image on Sat, 03 Feb 2018 09:59:38 GMT]]>@substring

I use overlays for scanlines? But I guess you're meant somthing else.

I have now tried without hdmi timings. I also tried dpi_group 2 and dpi_mode 4 to no success.

No image whatsoever. My crt monitor does notice when I plugg the vga in and out.

]]>https://forum.recalbox.com/post/88667https://forum.recalbox.com/post/88667Sat, 03 Feb 2018 09:59:38 GMT<![CDATA[Reply to RetroTINK-Ultimates no image on Sat, 03 Feb 2018 09:49:34 GMT]]>@mr-karmeck does ut need a particular overlay ?

]]>https://forum.recalbox.com/post/88663https://forum.recalbox.com/post/88663Sat, 03 Feb 2018 09:49:34 GMT<![CDATA[Reply to RetroTINK-Ultimates no image on Sat, 03 Feb 2018 09:06:22 GMT]]>@substring I do not, no image. I'm yet to test without any hdmi_timings though, will test to use only dpi_group=2 dpi_mode=87 when I get home.

]]>https://forum.recalbox.com/post/88655https://forum.recalbox.com/post/88655Sat, 03 Feb 2018 09:06:22 GMT<![CDATA[Reply to RetroTINK-Ultimates no image on Sat, 03 Feb 2018 08:39:11 GMT]]>@mr-karmeck the settings are for retroarch mostly, but you must edit your config.txt first of all. Have you done so ? Do you see emulationstation at least ?

]]>https://forum.recalbox.com/post/88652https://forum.recalbox.com/post/88652Sat, 03 Feb 2018 08:39:11 GMT